There is no LED lighting up when plugging it into the PC.
Latest posts made by Davidcgoodwin01
-
RE: Paneldue 5i Blown?
-
RE: Any Unused features?
Cool Thanks, I have Pressure advance, but I'm not using it now. the rest Ill give it a try.
-
Any Unused features?
Hi,
I am doing the frimware for my Core XY 300300360 printer. This is my complete firmware any one think that I am not using all the features at my disposal. I am using a duet 3 I just dont want a filament runout.
; Configuration file for Duet 3 (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.2 on Mon Feb 01 2021 21:18:26 GMT+0200 (South Africa Standard Time); General preferences
G90 ; Send absolute coordinates
M83 ; Relative extruder moves
M550 P"Viking" ; Set printer name to Viking
M669 K1 ; Select CoreXY mode
G21 ; Set to milimeters
M111 S0 ; Debugging off; Network
M552 P192.168.8.176 S1 ; enable network and acquire dynamic address via DHCP
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet; Drives
M569 P0.0 S1 ; physical drive 0.0 goes forwards
M569 P0.1 S1 ; physical drive 0.1 goes forwards
M569 P0.2 S1 ; physical drive 0.2 goes backwards
M569 P0.3 S0 ; physical drive 0.3 goes forwards
M584 X0.1 Y0.0 Z0.2 E0.3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z3204 E1004.00 ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E500 ; set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z360.00 E3000.00 ; set maximum speeds (mm/min)
M201 X3000.00 Y3000.00 Z360.00 E3000.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z1000 E1200 ; set motor currents (mA) and motor idle factor in per cent
;M84 S30 ; Set idle timeout; Axis Limits
M208 X-5 Y0 Z0 S1 ; set axis minima
M208 X300 Y300 Z360 S0 ; set axis maxima; Endstops
M574 X1 S3 ; configure sensorless endstop for high end on X
M574 Y2 S3 ; configure sensorless endstop for high end on Y
M574 Z1 S2 ; configure Z-probe endstop for low end on Z;Stall Detection
M915 X Y S3 R0 ; Stall detection on the X and Y axis With sensitivity set by S and Action set by R ("Take3 No Action");Pressure/Linear Advance
;M572 D0 S0.075 ; Pressure/Linear advance enabled with D selecting tool and S selecting value.; Z-Probe
M950 S0 C"io7.out" ; create servo pin 0 for BLTouch
M558 P9 C"^io7.in" H5 F360 T6000 A1 B0.2 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X-71 Y-42 Z3.0632 ; set Z probe trigger value, offset and trigger height
M557 X15:215 Y15:195 S40 ; define mesh grid; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"temp1" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin temp1
M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S270 ; set temperature limit for heater 1 to 270C; Fans
M950 F0 C"out7" Q500 ; create fan 0 on pin out4 and set its frequency - Cooling Fan
M106 P0 S1 H1 T45 ; set fan 0 value. Thermostatic control is turned on
M950 F1 C"out8" Q0 ; create fan 1 on pin out5 and set its frequency - Parts Cooling Fan
M106 P1 S0 H-1 ; set fan 1 value. Thermostatic control is turned off; Tools
M563 P0 D0 H1 F0:1 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C; Custom settings are not defined
; Miscellaneous
M575 P1 S1 B57600 ; enable support for PanelDue - io_0
M501 ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss -
RE: Paneldue 5i Blown?
I intentionally hit the erase button a couple of times, but BOSSA cant see the comport.
-
Paneldue 5i Blown?
I connected the screen on a Duet 2 Wifi board and it worked perfectly. Now connecting it to the Duet 3 on the io_0 port with cable adjustments as needed and firmware I think correct the screen does not turn on as in no power. Connecting to the PC via USB is the same result...but there had been no incidents so I am at a loss for why it is doing what it is doing.
M575 P1 S1 B57600 ; enable support for PanelDue - io_0 is what I am using . -
RE: Duet 2 Wifi - Sensorless Homing Working Without M915.
But I'm guessing that is way it was that unreliable?
-
RE: Duet 2 Wifi - Sensorless Homing Working Without M915.
But I mean in the config file there is no other stall detection setting than the one disabled by the ";" and that I did not use untill now.
-
Duet 2 Wifi - Sensorless Homing Working Without M915.
Hi Everyone,
This is my first time posting. I have now done 2 duet 2 wifi boards. I have used the Configuration toll to configure only the second board. both work with sensorless homing.
Weird thing is, though my sensorless homing works straight out of the configuration tool(That is set to sensorless homing) which it should not. What could be the reason for that?
It works exactly as is:
; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.2 on Mon Jan 25 2021 14:03:35 GMT+0200 (South Africa Standard Time); General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"D01" ; set printer name
M669 K1 ; select CoreXY mode; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet; Drives
M569 P0 S0 ; physical drive 0 goes forwards
M569 P1 S0 ; physical drive 1 goes forwards
M569 P2 S0 ; physical drive 2 goes backwards
M569 P3 S1 ; physical drive 3 goes forwards
M584 X1 Y0 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E452 ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E400.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z360 E3000 ; set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z10.00 E250.00 ; set accelerations (mm/s^2)
M906 X700 Y700 Z1200 E800 I45 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X211 Y207.5 Z200 S0 ; set axis maxima; Endstops
M574 X2 S3 ; configure sensorless endstop for high end on X
M574 Y2 S3 ; configure sensorless endstop for high end on Y
M574 Z1 S2 ; configure Z-probe endstop for low end on Z;M915 X Y S0 R2
;Linear/Pressure Advance
M572 D0 S0.45; Z-Probe
M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H5 F360 T6000 R0.2 A2 B1 ; set Z probe type to bltouch and the dive height + speeds
G31 P25 X-37 Y18.5 Z1.780 ; set Z probe trigger value, offset and trigger height
M557 X30:180 Y70:208 S60 ; define mesh grid; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S270 ; set temperature limit for heater 1 to 270C; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C; Custom settings
; Filament Runout
M591 P2 C"e0_stop" S1 D0 ; filament runout simple sensor (high signal when filament present)M501
And the the sensorless homing stopped, now I know it is because the M915 is uncommented, but it worked without it as well.
Any Toughts?
Very Cool board btw!