Thank you very much, that fixed my problem.
Thanks again
Thank you very much, that fixed my problem.
Thanks again
Hi, I currently have a Duet 3 mini 5+ alongside a Raspberry Pi 3b + and for some time now I have been receiving the following message when turning on my printer: "Warning: Incompatible firmware, please upgrade as soon as possible". Of course I tried to update the firmware using the package manager on the Raspberry, but it tells me that I have installed the latest firmware (3.3.0) being that DWC reports that I am using version 3.2.2.
This is what I get when running an M112:
M122
=== Diagnostics ===
RepRapFirmware for Duet 3 Mini 5+ version 3.2.2 running on Duet 3 Mini5plus Ethernet (SBC mode)
Board ID: LUR9T-W096U-D65J0-40KMS-1803Z-7MXNN
Used output buffers: 1 of 40 (11 max)
=== RTOS ===
Static ram: 98732
Dynamic ram: 94468 of which 44 recycled
Never used RAM 51972, free system stack 200 words
Tasks: Linux(blocked,105) HEAT(blocked,315) CanReceiv(blocked,947) CanSender(blocked,372) CanClock(blocked,363) TMC(blocked,106) MAIN(running,519) IDLE(ready,20) AIN(blocked,269)
Owned mutexes: HTTP(MAIN)
=== Platform ===
Last reset 00:16:07 ago, cause: power up
Last software reset at 2021-08-01 22:22, reason: User, GCodes spinning, available RAM 51972, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00430000 BFAR 0xe000ed38 SP 0x00000000 Task Linu Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Aux1 errors 0,0,0
Supply voltage: min 0.0, current 23.2, max 23.3, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 11, reads 62381, writes 11, timeouts 0, DMA errors 0
Driver 1: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 13, reads 62379, writes 13, timeouts 0, DMA errors 0
Driver 2: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 13, reads 62378, writes 13, timeouts 0, DMA errors 0
Driver 3: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 13, reads 62378, writes 13, timeouts 0, DMA errors 0
Driver 4: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 13, reads 62379, writes 13, timeouts 0, DMA errors 0
Driver 5: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 13, reads 62379, writes 13, timeouts 0, DMA errors 0
Driver 6: position 0, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 13, reads 62378, writes 13, timeouts 0, DMA errors 0
Date/time: 2021-08-02 19:23:11
Cache data hit count 2299187756
Slowest loop: 1.23ms; fastest: 0.08ms
=== Storage ===
Free file entries: 10
SD card 0 not detected, interface speed: 0.0MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1, chamberHeaters = -1 -1
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP* is doing "M122" in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== CAN ===
Messages queued 8696, send timeouts 8694, received 0, lost 0, longest wait 0ms for reply type 0, free buffers 16
=== SBC interface ===
State: 4, failed transfers: 1
Last transfer: 4ms ago
RX/TX seq numbers: 33930/33930
SPI underruns 0, overruns 0
Number of disconnects: 0, IAP RAM available 0x113e0
Buffer RX/TX: 0/0-0
=== Duet Control Server ===
Duet Control Server v3.3.0
Code buffer space: 4096
Configured SPI speed: 8000000Hz
Full transfers per second: 35.11, max wait times: 14.8ms/0.0ms
Codes per second: 0.07
Maximum length of RX/TX data transfers: 3424/984
And this is what I get when trying to update via apt:
sudo apt-get upgrade duetsoftwareframework
Reading package lists... Done
Building dependency tree
Reading state information... Done
duetsoftwareframework is already the newest version (3.3.0).
Calculating upgrade... Done
0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded.
It is nothing that prevents me from printing, in fact I have been with this problem for about a month, but I would like to solve it ... I hope you can help me