@Phaedrux
Hallo, i have create a new config.g File with the Config Tool and now it runs well
Best posts made by H2SO4
-
RE: G28 Bad Dommand
Latest posts made by H2SO4
-
RE: G28 Bad Dommand
@Phaedrux
Hallo, i have create a new config.g File with the Config Tool and now it runs well -
RE: G28 Bad Dommand
@Phaedrux
Hallo, I try this, but it don't work
the Board shows the same G28 Bad Command
for Z-Probe i use a npn inductive sensor from ChinaThank You
-
RE: G28 Bad Dommand
Sorry,
i'm new with this themes
was i mean are the settings for the Hotend, also P0
it is a E3D lite -
RE: G28 Bad Dommand
Hallo,
after some read i've found this Setting:
M305 P1 B4725 C7.060000e-8
it that o.k.?
Thank You -
RE: G28 Bad Dommand
@Veti said in G28 Bad Dommand:
B4138 is the default and wrong for your thermistors
Thank You,
when B4138 is the wrong setting, what is the correct value? -
RE: G28 Bad Dommand
@dc42
no, the deployprobe.g and retractprobe.g files in /sys are not on the SD card -
RE: G28 Bad Dommand
With the "Home ALL Button" in Web Control, but it is the same when i use G28 in Slicr Startcode
-
G28 Bad Dommand
Hallo,
since a few Weeks I used the Duet 2 Wifi Board in my Prínter, and it works very good.
Only one little Problem is there:
When I start "homing all axes", the Board shows "G28 Bad Command"
The homing procedure runs well.
Does anyone have experience with this problem, I would be very grateful for advice?Here are the files config.g and homeall.g
; Configuration file for Duet WiFi (firmware version 2.03) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v2.1.4 on Sun Dec 22 2019 16:22:28 GMT+0100 (Mitteleuropäische Normalzeit) ; General preferences G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"Printer" ; set printer name M667 S1 ; select CoreXY mode ; Network M552 S1 ; enable network M586 P0 S1 ; enable HTTP M586 P1 S0 ; disable FTP M586 P2 S0 ; disable Telnet ; Drives M569 P0 S1 ; physical drive 0 goes forwards M569 P1 S1 ; physical drive 1 goes forwards M569 P2 S0 ; physical drive 2 goes backwards M569 P3 S1 ; physical drive 3 goes forwards M584 X0 Y1 Z2 E3 ; set drive mapping M350 X128 Y128 Z128 E128 I0 ; configure microstepping without interpolation M92 X640.00 Y640.00 Z12800 E761.60 ; set steps per mm M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min) M203 X6000.00 Y6000.00 Z250 E1200.00 ; set maximum speeds (mm/min) M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2) M906 X1200 Y1200 Z1500 E1800 I30 ; set motor currents (mA) and motor idle factor in per cent M84 S10 ; Set idle timeout ; Axis Limits M208 X0 Y0 Z0 S1 ; set axis minima M208 X240 Y240 Z200 S0 ; set axis maxima ; Endstops M574 X1 Y1 S0 ; set endstops controlled by motor stall detection M574 Z1 S2 ; set endstops controlled by probe ; Z-Probe M558 P5 H5 I1 F120 T4800 ; set Z probe type to switch and the dive height + speeds G31 P500 X0 Y0 Z0.55 ; set Z probe trigger value, offset and trigger height M557 X2:220 Y2:220 S110 ; define mesh grid ; Heaters M305 P0 T100000 B4138 R4700 ; set thermistor + ADC parameters for heater 0 M143 H0 S70 ; set temperature limit for heater 0 to 70C M305 P1 T100000 B4138 R4700 ; set thermistor + ADC parameters for heater 1 M143 H1 S250 ; set temperature limit for heater 1 to 250C ; Fans M106 P0 S0 I0 F500 H-1 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off M106 P1 S1 I0 F500 H-1 ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off ; Tools M563 P0 D0 H1 F0 ; define tool 0 ;G10 P0 X0 Y0 Z0.0 ; set tool 0 axis offsets ;G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C ; Custom settings are not defined M915 X Y S5 R0 ; Configure motor stall detection M106 P0 F25 ; Set Fan0 Freq to 25 Hz M501 ; Read stored parameters
; homeall.g ; called to home all axes ; ; generated by RepRapFirmware Configuration Tool v2.1.4 on Sun Dec 22 2019 16:22:28 GMT+0100 (Mitteleuropäische Normalzeit) G91 ; relative positioning G1 H2 Z5 F1500 ; lift Z relative to current position ;G1 H1 X-250 Y-250 F100 ; move quickly to X or Y endstop and stop there (first pass) G1 H1 Y-250 ; home Y axis G1 H1 X-250 ; home X axis G1 X5 F1500 ; go back a few mm G1 H1 X-250 F360 ; move slowly to X axis endstop once more (second pass) G1 Y5 F1500 ; go back a few mm G1 H1 Y-250 F360 ; then move slowly to Y axis endstop G90 ; absolute positioning G1 X120 Y120 F1500 ; go to first bed probe point and home Z G30 ; home Z by probing the bed G1 Z5 F1500 ; go back a few mm ; Uncomment the following lines to lift Z after probing ;G91 ; relative positioning ;G1 S2 Z5 F80 ; lift Z relative to current position ;G90 ; absolute positioning