Posts made by hartmannjan

@phaedrux
Thank you really much for the help.
I updated the firmware and the web control and now everything works fine.

Kind Regards
Jan

Hello,
I have a Duet Wifi Board with a Duex 5 installed.
When I try to upload any G-Code, I get this error message:

I tried the following without any results:

• Change Browser and Clean Cache

• Backup all Files from the SD Card and run SD Card Formatter

• Change SD Cards

• Different PC to upload files

I make my G-Code Files with Simplify 3D.

My M122 report is here:

=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.0(RTOS) running on Duet WiFi 1.02 or later + DueX5
Board ID: 08DGM-9T6BU-FG3SN-6J1FG-3SJ6Q-KBWZG
Used output buffers: 1 of 20 (6 max)
=== RTOS ===
Static ram: 28380
Dynamic ram: 95772 of which 0 recycled
Exception stack ram used: 332
Never used ram: 6588
Task NETWORK ready, free stack 396
Task HEAT blocked, free stack 1256
Task MAIN running, free stack 3568
=== Platform ===
Last reset 00:00:14 ago, cause: software
Last software reset at 2018-11-08 20:35, reason: User, spinning module GCodes, available RAM 6508 bytes (slot 3)
Software reset code 0x0003 HFSR 0x00000000, CFSR 0x00000000, ICSR 0x0441f000, BFAR 0xe000ed38, SP 0xffffffff
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms
MCU temperature: min 19.0, current 19.2, max 19.4
Supply voltage: min 11.8, current 11.9, max 11.9, under voltage events: 0, over voltage events: 0
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Driver 5: standstill, SG min/max not available
Driver 6: standstill, SG min/max not available
Driver 7: standstill, SG min/max not available
Driver 8: standstill, SG min/max not available
Driver 9: standstill, SG min/max not available
Expansion motor(s) stall indication: no
Date/time: 2018-11-08 20:36:02
Slowest loop: 4.28ms; fastest: 0.07ms
=== Move ===
Hiccups: 0, StepErrors: 0, LaErrors: 0, FreeDm: 240, MinFreeDm 240, MaxWait: 0ms, Underruns: 0, 0
Scheduled moves: 0, completed moves: 0
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heaters = -1 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 14.14ms; fastest: 0.01ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8

• WiFi -
  Network state is running
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 0
  WiFi firmware version 1.21
  WiFi MAC address 84:f3:eb:83:2b:08
  WiFi Vcc 3.43, reset reason Power on
  WiFi flash size 4194304, free heap 17696
  WiFi IP address 192.168.178.88
  WiFi signal strength -69dBm, reconnections 0, sleep mode modem
  Socket states: 0 0 0 0 0 0 0 0
  === Expansion ===
  DueX I2C errors 0

Thankyou for your help

Kind Regards
Jan