Sure. Here you go
; Configurat; Configuration file for Duet WiFi / Ethernet
; executed by the firmware on start-up
; General preferences
M111 S0 ; Debugging off
G21 ; Work in millimetres
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves
M555 P2 ; Set firmware compatibility to look like Marlin
; Network
; Read https://duet3d.dozuki.com/Wiki/Gcode#Section_M587_Add_WiFi_host_network_to_remembered_list_or_list_remembered_networks
M550 P"ToolChanger" ; Set machine name
M552 S1 ; Enable Networking
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
;M586 P2 S0 ; Disable Telnet
M586 P2 S1 T0 ; enable telnet
M575 P1 S1 B57600 ; Paneldue
M667 S1 ; Select CoreXY mode
; Endstops
M574 X1 S3 ; Set X endstop stall detection
M574 Y1 S3 ; Set Y endstop stall detection
M574 Z0 P"nil";
M558 P5 C"zstop" H3 F150 T20000
M574 C1 S3 ; Stall detect coupler at low end of its range
G31 P200 X0 Y0 Z0 ; Set Z probe trigger value, offset and trigger height
M557 X10:290 Y20:180 S40 ; Define mesh grid
; Drive direction
M569 P0 S0 ; Drive 0 X
M569 P1 S0 ; Drive 1 Y
M569 P2 S1 ; Drive 2 Z
M569 P3 S0 ; Drive 3 E0
M569 P4 S0 ; Drive 4 E1
M569 P5 S1 ; Drive 5 E2
M569 P6 S1 ; Drive 6 E3
M569 P7 S0 ; Drive 7 COUPLER
M569 P8 S0 ; Drive 8 UNUSED
M569 P9 S0 ; Drive 9 UNUSED
M584 X0 Y1 Z2 C7 E3:4:5:6 ; Apply custom drive mapping
M208 X-35:328.5 Y-49:243 Z0:300 C0:260 S0 ; Set axis maxima & minima
M350 E16:16:16:16 C8 I0 ; Configure microstepping without interpolation
M350 X16 Y16 Z16 I1 ; Configure microstepping with interpolation
M92 X100.2 Y100.2 Z1600 C100 E740:740:740:375 ; Set steps per mm
M566 X400 Y400 Z8 C2 E2:2:2:2 ; Set maximum instantaneous speed changes (mm/min)
M203 X35000 Y35000 Z1200 C5000 E5000:5000:5000:5000 ; Set maximum speeds (mm/min)
M201 X6000 Y6000 Z400 C400 E2500:2500:2500:2500 ; Set accelerations (mm/s^2)
M906 X2000 Y2000 Z1330 C400 E1680:1680:1680:1000 I30 ; Set motor currents (mA) and motor idle factor in percent
M84 S120 ; Set idle timeout
;Stall Detection
M915 C S5 F0 H200 ; Coupler
;Stall Detection
M915 X Y S5 F0 H400 ; X / Y Axes
; Heaters
; Bed
M308 S0 P"bed_temp" Y"thermistor" A"Bed" T100000 B4725 C7.06e-8 ; define bed temperature sensor
M950 H0 C"bed_heat" T0 ; heater 0 uses the bed_heat pin, sensor 0
M140 H0 ; the bed heater is heater 0
M143 H0 S225 ; Set temperature limit for heater 0 to 225C
; Tool 0
M308 S1 P"e0temp" Y"thermistor" A"T0" T100000 B4725 C7.06e-8 ; Set thermistor
M950 H1 C"e0heat" T1 ; Extruder 0 heater
M143 H1 S300 ; Set temperature limit for heater 1 to 300C
M563 P0 S"Titan/V6 0.4" D0 H1 F2 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Reset tool 0 axis offsets
G10 P0 R0 S0 ; Reset initial tool 0 active and standby temperatures to 0C
M950 F1 C"fan1"
M950 F2 C"fan2"
M106 P1 S255 H1 T70 ; T0 HE
M106 P2 S0 ; T0 PCF
; Tool 1
M308 S2 P"e1temp" Y"thermistor" A"T1" T100000 B4725 C7.06e-8 ; Set thermistor
M950 H2 C"e1heat" T2 ; Extruder 0 heater
M143 H2 S300 ; Set temperature limit for heater 2 to 300C
M563 P1 S"Titan/V6 0.4" D1 H2 F4 ; Define tool 1
G10 P1 X0 Y0 Z0 ; Reset tool 1 axis offsets
G10 P1 R0 S0 ; Reset initial tool 1 active and standby temperatures to 0C
M950 F3 C"duex.fan3"
M950 F4 C"duex.fan4"
M106 P3 S255 H2 T70 ; T1 HE
M106 P4 S0 ; T1 PCF
; Tool 2 Volcano
M308 S3 P"e2temp" Y"thermistor" A"T2" T100000 B4725 C7.06e-8 ; Set thermistor
M950 H3 C"duex.e2heat" T3 ; Extruder 0 heater
M143 H3 S300
M563 P2 S"Titan/Volcano 0.8" D2 H3 F6 ; Define tool 2
G10 P2 X0 Y0 Z0 ; Reset tool 2 axis offsets
G10 P2 R0 S0 ; Reset initial tool 2 active and standby temperatures to 0C
M950 F5 C"duex.fan5"
M950 F6 C"duex.fan6"
M106 P5 S255 H3 T70 ; T2 HE
M106 P6 S0 ; T2 PCF
; Tool 3 Hemera
M308 S4 P"e3temp" Y"thermistor" A"T3" T100000 B4725 C7.06e-8 ; Set thermistor
M950 H4 C"duex.e3heat" T4 ; Extruder 0 heater
M143 H4 S300
M563 P3 S"Hemera 0.4" D3 H4 F8 ; Define tool 3
G10 P3 X0 Y0 Z0 ; Reset tool 3 axis offsets
G10 P3 R0 S0 ; Reset initial tool 3 active and standby temperatures to 0C
M950 F7 C"duex.fan7"
M950 F8 C"duex.fan8"
M106 P7 S255 H4 T70 ; T3 HE
M106 P8 S0
; Fans
M950 F0 C"fan0"
M106 P0 S0 ; Enclosure LEDs
M593 F50 ; cancel ringing at 50Hz (https://forum.e3d-online.com/threads/accelerometer-and-resonance-measurements-of-the-motion-system.3445/)
;tool offsets
G10 P0 X-9 Y39 Z-5.6 ; T0 seems to be .1ish mm taller than T1
G10 P1 X-9 Y39 Z-5.6 ; T1
G10 P2 X-9 Y39 Z-14.5
G10 P3 X23 Y41 Z-6.3 ; T3 Hemera
;deselect tools
T-1
;M572 D0 S0.5 ; pressure advance T0
;M572 D1 S0.5 ; pressure advance T1
;M572 D2 S0.5 ; pressure advance T2
;M572 D3 S0.0315 ; pressure advance T3
; Pid Tuning
; M307 H0 R1.475 C373.5 D2.60 S1.00 ; Disabled as causes issues with heating up from very cold
M307 H1 R2.602 C169.9 D6.11 S1.00 V24.2
M307 H2 R2.668 C185.0 D5.80 S1.00 V24.2
M307 H3 R2.072 C248.8 D6.16 S1.00 V24.2
M307 H4 R2.769 C203.5 D5.69 S1.00 V24.3
;M501; load config-override.g