Apologies: I must have missed your message.
Config.g for you to peruse:
; Configurat; Configuration file for Duet WiFi / Ethernet
; executed by the firmware on start-up
; General preferences
M111 S0 ; Debugging off
G21 ; Work in millimetres
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves
M555 P2 ; Set firmware compatibility to look like Marlin
; Network
M550 P"ToolChanger" ; Set machine name
;M587 S"ssid" P"password" ; WiFi Settings
;M552 S1 P"ssid" ; Enable WiFi Networking
M552 S1 ; Enable Networking
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet
M667 S1 ; Select CoreXY mode
; Endstops
;M574 X1 Y1 S3 ; Set X / Y endstop stall detection (edit out for physical switches - JS 01/11/2019)
M574 X1 Y1 S1 ; Set physical end-stops
M574 Z1 S2 ; Set Z endstop probe
M558 P7 X0 Y0 Z2 H3 F360 I0 T20000 ; Set Z probe type to switch, the axes for which it is used and the dive height + speeds
G31 P200 X0 Y0 Z0 ; Set Z probe trigger value, offset and trigger height
M557 X10:290 Y20:180 S40 ; Define mesh grid
; Drive direction
M569 P0 S0 ; Drive 0 X
M569 P1 S0 ; Drive 1 Y
M569 P2 S1 ; Drive 2 Z
M569 P3 S1 ; Drive 3 E0
M569 P4 S0 ; Drive 4 E1
M569 P5 S1 ; Drive 5 E2
M569 P6 S1 ; Drive 6 E3
M569 P7 S0 ; Drive 7 COUPLER
M569 P8 S0 ; Drive 8 UNUSED
M569 P9 S0 ; Drive 9 UNUSED
M584 X0 Y1 Z2 C7 E3:4:5:6 ; Apply custom drive mapping
M208 X-35:328.5 Y-49:243 Z0:300 C0:500 S0 ; Set axis maxima & minima
M350 E16:8:16:16 C8 I0 ; Configure microstepping without interpolation
M350 X16 Y16 Z16 I1 ; Configure microstepping with interpolation
M92 X100 Y100 Z1600 C100 E830:415:409:830 ; Set steps per mm
M566 X500 Y500 Z45 C2 E180:180:800:200 ; Set maximum instantaneous speed changes (mm/min) (800)
M203 X35000 Y35000 Z1200 C5000 E3600:3600:5000:3600 ; Set maximum speeds (mm/min) (6000)
M201 X5000 Y5000 Z400 C500 E2000:2000:2500:2500 ; Set accelerations (mm/s^2)
M906 X1500 Y1500 Z1200 C500 E1100:1000:1100:1100 I30 ; Set motor currents (mA) and motor idle factor in percent
M84 S120 ; Set idle timeout
;Stall Detection
M915 C S6 F0 H200 R4700 ; Coupler
;Stall Detection
M915 X Y S2 F0 H400 R4700 ; X / Y Axes
; Heaters
M305 S"Bed Temperature" P0 T100000 B4138 C0 ; Set thermistor
M143 H0 S225 ; Set temperature limit for heater 0 to 225C
;M305 S"T0" P1 R4700 T100000 B4388 ; Set thermistor, old E3D Config
M305 S"T0" P1 X200 ; Set therminstor, to PT100 input 1 on Duet mainboard (200)
M143 H1 S375 ; Set temperature limit for heater 1 to 375C (hardened 0.25mm nozzle, copper block)
;M305 S"T1" P2 R4700 T100000 B4388 ; Set thermistor, old E3D Config
M305 S"T1" P2 X201 ; Set thermistor, to PT100 input 2 on Duet mainboard (201)
M143 H2 S400 ; Set temperature limit for heater 2 to 375C (nozzle-x 0.4mm nozzle, copper block)
;M305 S"T2" P3 R4700 T100000 B4388 ; Set thermistor, old E3D Config
M305 S"T2" P3 X204 ; Set thermistor, to PT100 input 1 on Duex board (204)
M143 H3 S375 ; Set temperature limit for heater 3 to 400C (coated copper 0.4mm nozzle, copper block)
;M305 S"T3" P4 R4700 T100000 B4388 ; Set thermistor, old E3D Config
M305 S"T3" P4 X205 ; Set thermistor, to PT100 input 1 on Duex board (205)
M143 H4 S375 ; Set temperature limit for heater 1 to 375C (hardened 0.8mm nozzle, copper volcano block)
M305 S"Chamber temp" P5 T100000 B4725 C7.060000e-8 X1 ; Case temp 100k semtek on E0 thermistor input (R4700 deleted)
M141 H5 ; Chamber heater configured so shows up in UI
; Tools
M563 P0 S"T0" D0 H1 F2 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Reset tool 0 axis offsets
G10 P0 R0 S0 ; Reset initial tool 0 active and standby temperatures to 0C
M563 P1 S"T1" D1 H2 F4 ; Define tool 1
G10 P1 X0 Y0 Z0 ; Reset tool 1 axis offsets
G10 P1 R0 S0 ; Reset initial tool 1 active and standby temperatures to 0C
M563 P2 S"T2" D2 H3 F6 ; Define tool 2
G10 P2 X0 Y0 Z0 ; Reset tool 2 axis offsets
G10 P2 R0 S0 ; Reset initial tool 2 active and standby temperatures to 0C
M563 P3 S"T3" D3 H4 F8 ; Define tool 3
G10 P3 X0 Y0 Z0 ; Reset tool 3 axis offsets
G10 P3 R0 S0 ; Reset initial tool 3 active and standby temperatures to 0C
; Fans
M106 P0 S0 ; UNUSED
M106 P1 S255 H1 T70 ; T0 HE
M106 P2 S0 ; T0 PCF
M106 P3 S255 H2 T70 ; T1 HE
M106 P4 S0 ; T1 PCF
M106 P5 S255 H3 T70 ; T2 HE
M106 P6 S0 ; T2 PCF
M106 P7 S255 H4 T70 ; T3 HE
M106 P8 S0 ; T3 PCF
M593 F50 ; cancel ringing at 50Hz
;M376 H15 ; bed compensation taper
;tool offsets
G10 P0 X1 Y39 Z-3.78 ; T0
G10 P1 X1 Y39 Z-3.58 ; T1
G10 P2 X21 Y44 Z-5.72 ; T2
G10 P3 X1 Y39 Z-12.24 ; T3 (volcano)
;deselect tools
T-1
They are a little bit all over the place as I have been tweaking and fiddling to get things to work. The E3D config has everything ramped up to the max with the intention the user tunes to their needs.
Jai