Posts made by Kryckan
-
RE: Not loading macro from G-code
@dc42
Turns out I don't have a Start.g in the file system. ... and the cancel.g is just a bunch of HTML? Just got a load of errors when canceling the job.Strange because I just flashed the Duet a week ago. Think I need to go over the file system.
Is the Start.g supposed to be in the system folder? -
RE: Not loading macro from G-code
@dc42
Damn! You are so fast at answering in the forum! I just love it!Ahh, so the start.g would be a better place to set the macro then. I will try that.
Thanks. -
RE: Not loading macro from G-code
Okay, so I think the error is not in Duet.
I was trying to start the print from my Repetier Server attached to the Duet. Seems like there is something getting wrong in the fransfer.
I think it removes the colon and maybe the quotes?
When I upload the G-code directly to the duet, it runs fine. -
Not loading macro from G-code
I hope I just missed something here.
I have made a macro for the start of the print.; Ready printer and calibrate bed M83 ; Set extruder to relative moves G21 ; set mm units G90 ; set absolute coordinates G28 ; Home Machine M561 ; Clear any bed transform G1 X140 Y117 F8000 ; Go to center of bed G1 Z10 F8000 ; Go to 10mm over bed G30 ; Probe bed and set Z-height G29 ; Run mesh compensation M593 F80. ; Set Dynamic Acceleration Adjustment to 80Hz ; Extrude anchor M703 ; Set filament parameters G1 X0 Y0 F5000 ; Go to home origo G92 E0. ; Zero exreuder G1 Z0.6 ; Move nossle down G1 E45. F500 ; Extrude anchor G92 E0. ; Zero extruder G1 E-1.3 F25 ; Retract filament G1 Z10.0 F300 ; Move platform down 5mm G1 Y20. F3000 ; Move away from the anchor M99 ; Go back to main program
Wen I run this in console, the macro starts.
M98 P"0:/macros/start_of_print.g"
But when I have the same command in a program:
.... G90 M83 M106 S0 M140 S60 M190 S60 M104 S215 T0 M109 S215 T0 M98 P"0:/macros/start_of_print.g" ; process Process1 ; layer 1, Z = 0.300 T0 ; feature skirt ; tool H0.300 W0.480 G1 Z0.300 F120 .....
The duet returns:
Warning: Macro file 0 /macros/start_of_print.g not found
Any ideas?
Board: Duet WiFi 1.02 or later
Firmware: RepRapFirmware for Duet 2 WiFi/Ethernet 3.01-RC4 (2020-03-16b1)
Duet WiFi Server Version: 1.23 -
RE: Wait for chamber temp without heater?
Works like a charm!
For anyone that want to use this, put this in your macro:
*while sensors.analog[2].lastReading < 50 G4 S1 M99*
And your startup script:
*M98 P"0:/macros/Chamber temp/chamber_temp_50.g"*
And of course name it to what you want and set the correct sensor number and temperature. And be sure to use RRF 3.01-RC4 or later.
Thank you for your help.
/Christian -
RE: Wait for chamber temp without heater?
@dc42
Yes I was using this:
M308 S2 P"e1temp" Y"thermistor" T100000 B4725 C7.06e-8 A"Chamber"
But couldnt figure out how to use it. Wasn't aware of the ability to use logic code.
Thanks! -
RE: Wait for chamber temp without heater?
@bearer
Interresting. Sound like the way to go when you read the description. I will try that. -
RE: Wait for chamber temp without heater?
@Phaedrux
I use RRF3 and was just trying to use as a independent probe. But I haven't found how to use it in the way I want.
Maybe it's easier to do like you said, and make the bed the heater at startup and then switch it over. I'm only going to use it for ABS and such, so scripting it to a specific temp in each profile is not a bad idea. -
Wait for chamber temp without heater?
Hello everybody.
I want to have control of the chamber temp but not sure yet that I want a chamber heater.
Is there a way to get the printer to wait for a chamber temp without using a chamber heater, just the heated bed?
I just get a fault trying M191 because it wants a heater as well.Any ideas?
Thank you!
/Christian