@CaLviNx Thanks for all your help too mate, I don't really need them to probe at different speeds, just having it probe twice will also work for me.
Latest posts made by MichaelMD1978
-
RE: RRF 3.1.1 Probe Issues
-
RE: RRF 3.1.1 Probe Issues
@CaLviNx Thanks for the help mate, I will give it a try.
-
RE: RRF 3.1.1 Probe Issues
@CaLviNx This is my current M558:
M558 P5 C"zprobe.in" H5 F120 T6000 ; set Z probe type to unmodulated and the dive height + speeds
How do I edit that to probe twice?
-
RE: RRF 3.1.1 Probe Issues
@CaLviNx how would that look in the config.g?
-
RE: RRF 3.1.1 Probe Issues
@CaLviNx Thanks, I will give this a try. I would rather fix the M558 in config.g though as this also happens in my mesh levelling.
-
RE: RRF 3.1.1 Probe Issues
@dc42 If you see anything else in my config that could be wrong, please let me know. The Probe is a Pinda 5v
-
RE: RRF 3.1.1 Probe Issues
; Configuration file for Duet WiFi (firmware version 3.1.1)
; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"BLV AM8" ; set printer name; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M569 P4 S1 ; physical drive 4 goes forwards
M584 X0 Y1 Z2:4 E3 ; set drive mapping
M671 X0:220 Y110:110 S2 ; leadscrews left & right (Middle of the bed in the Y axis)
M350 X16 Y16 Z16 E16 I0 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E400.00 ; set steps per mm
M566 X1000.00 Y1000.00 Z40.00 E1000.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z1000.00 E6000.00 ; set maximum speeds (mm/min)
M201 X2500.00 Y2500.00 Z100.00 E2500.00 ; set accelerations (mm/s^2)
M906 X1500 Y1500 Z720 E1500 I45 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 X-4 Y-50 Z0 S1 ; set axis minima
M208 X220 Y210 Z250 S0 ; set axis maxima; Endstops
M574 X1 S1 P"!xstop"
M574 Y1 S1 P"!ystop" ; set active low and disabled endstops
M574 Z1 S2 ; set endstops controlled by probe; Z-Probe
M558 P5 C"zprobe.in" H5 F120 T6000 ; set Z probe type to unmodulated and the dive height + speeds
G31 P500 X0 Y37.5 Z0.70 ; set Z probe trigger value (was at P500, I am testing P1000), offset and trigger height (Higher is closer to the bed!)
M557 X10:210 Y10:210 S10 ; define mesh grid; Heaters
; Bed
M308 S0 P"bed_temp" Y"thermistor" T100000 B4138 R4700 ; New Value for 3.1.1
M950 H0 C"bed_heat" T0 ; New Value for 3.1.1
M307 H0 A135.7 C683.7 D2.1 V11.8 B0 S1.00 ; Disable bang-bang mode and add PID Values for the bed heater and set PWM limit
M140 H0 ; Map Heated Bed to Heater 0 on the GUI
M143 H0 S120 ; Set the Bed Max Temp to 120 Degrees; Hotend
M308 S1 P"spi.cs1" Y"rtd-max31865" R395 F50 ; create sensor number 1 as a PT100 sensor in the first position on the Duet 2 daughter board connector
M950 H1 C"e0_heat" T1 ; New Value for 3.1.1
M307 H1 A636.2 C264.9 D5.8 V11.8 B0 S1.00 ; disable bang-bang mode and set PID Values for the Hotend heater and set PWM limit
M143 H1 S270 ; Set the Hotend Max Temp to 270 Degrees; Chamber
M308 S2 P"e1_temp" Y"thermistor" T100000 B4138 C0 R4700 ; New Value for 3.1.1
M950 H2 C"e1_heat" T2 ; New Value for 3.1.1
M307 H2 A42.6 C3913.4 D5.0 V12.2 B0 S1.00 ; Chamber PID Values - Testing These!
;M307 H2 A11 C99000 D2000 B1 ; chamber heater operates in bang-bang mode
M141 H2 ; Map Heated Bed to Heater 0 on the GUI
M143 H2 S80 ; Set the Chamber Max Temp to 80 Degrees; Fans
; Part Fan
M950 F0 C"fan0" Q500 ; New Value for 3.1.1
M106 P0 S0 I0 F500 H-1 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off; Hotend Fan
M950 F1 C"fan1" Q500 ; New Value for 3.1.1
M106 P1 S1 H1 T45 ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C; Custom settings are not defined
; Miscellaneous
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
T0 ; select first tool -
RRF 3.1.1 Probe Issues
Hello Guys, I just can't seem to find an answer on my Issue. I was running 2.05.1 and everything was working well, so I decided to make my life difficult and move to 3.1.1 and now I am having some trouble with my Probe. Before there would always be a double probe action, it would probe once fast and once slow in each spot, now it only probes each point once? Has anyone else noticed this and how can I fix it?