@dc42 said in LCD display temperature:
The G10 P0 command must come after the M563 P0 command.
thanks it works
@dc42 said in LCD display temperature:
The G10 P0 command must come after the M563 P0 command.
thanks it works
okay thanks.
here my config.g.
; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
; General preferences
G21 ; Work in millimetres
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves
M111 S0 ; Debug off
M665 L267 R135.260 B116 H291.300 X-0.880, Y -0.300, Z 0.000 ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0.01 Y0.01 Z-0.01, tilt X0.00% Y0.00% ; Put your endstop adjustments here, or let auto calibration find them
; Network
M550 P"Anycubic" ; Set machine name
M552 S1 ; Turn network on
M587 S"WiFi_UFLR" P"3542@WRMR!" ; Configure access point. You can delete this line once connected
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet
; Drives
M569 P0 S1 ; drive 0 goes forwards
M569 P1 S1 ; drive 1 goes forwards
M569 P2 S1 ; drive 2 goes forwards
M569 P3 S1 ; drive 3 goes forwards
M569 P4 S1 ; drive 4 goes forwards
M574 X2 Y2 Z2 S1 ; set endstop configuration (all endstops at high end, active high)
M84 S30 ; Set idle timeout
M92 X80.00 Y80.00 Z80.00 E96.00 ; Set steps per mm
M201 X2000.00 Y2000.00 Z2000.00 E2.00 ; Set accelerations (mm/s^2)
M203 X12000.00 Y12000.00 Z12000.00 E3000.00 ; Set maximum speeds (mm/min)
M350 X256 Y256 Z256 E256 I1 ; Configure microstepping with interpolation
M566 X300.00 Y300.00 Z300.00 E300.00 ; Set maximum instantaneous speed changes (mm/min)
M906 X900.00 Y900.00 Z900.00 E700.00 I30 ; Set motor currents (mA) and motor idle factor in per cent
; Z-Probe
G31 P100 X0 Y0 Z18.598 ; Set Z probe trigger value, offset and trigger height
M557 R110 S25 ; Define mesh grid
M558 P4 H1 F120 T6000 ; Set Z probe type to switch and the dive height + speeds
; Heaters
M143 H0 S100 ; Set temperature limit for heater 0 (Bed) to 100C
M143 H1 S260 ; Set temperature limit for heater 1 (Nozzel) to 260C
M305 P0 T97000 B4267 R4700 ; Set thermistor + ADC parameters for heater 0 (Bed)
M305 P1 T100000 B4267 R4700 ; Set thermistor + ADC parameters for heater 1 (Nozzel)
M307 H0 A157.4, C706.8, D0.6 V12.4 B0 S1 ; Use PID on Bed heater (may require further tuning)
M307 H1 A415.2, C117.8, D5.5 V12.5 B0 S1 ; Use PID on Nozzel heater (may require further tuning)
; Fans
M106 P0 S0 I0 F250 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S0 I0 F250 H1 T50 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
; Tools
G10 P0 R0 S0 ; Set tool 0 active and standby temperatures to 0C
M563 P0 S"Nozzel" D0 F0 H1 ; Define tool 0, tool name, uses extruder drive 0, Fan 0, Heater 1
; Axis Limits
M208 Z0 S1 ; Set minimum Z
; Custom settings are not configured
; Miscellaneous
T0 ; select first hot end
T1 ; Select first tool
M501 ;Read parameters from override file
Hey everyone,
I have a question. and I hope someone can help me, my duet lcd display shows -273 at the nozzle temperature if it is not on while the bed temperature is just 0.