@SonnyD1 this is my setting of the limit switches with an Idex printer
; Endstops
M574 Y1 S1 P"io1.in"
M574 X1 S1 P"io2.in"
M574 U2 S1 P"io4.in"
M574 Z2 S1 P"io6.in"
I think U2 S1 would be correct right?
@SonnyD1 this is my setting of the limit switches with an Idex printer
; Endstops
M574 Y1 S1 P"io1.in"
M574 X1 S1 P"io2.in"
M574 U2 S1 P"io4.in"
M574 Z2 S1 P"io6.in"
I think U2 S1 would be correct right?
; Configuration file for Duet 3 Mini 5+ (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.15 on Sat Nov 26 2022 13:27:47 GMT+0100 (Mitteleuropäische Normalzeit)
; General preferences
M575 P1 S1 B57600 ; enable support for PanelDue
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Proschi 3D E2" ; set printer name
; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S1 ; enable Telnet
; Drives
M569 P0.0 S0 D3 H50 V30 ; physical drive 0.0 goes forwards
M915 P0.0 T50
M569 P0.1 S1 D3 H50 V30 ; physical drive 0.1 goes forwards
M915 P0.1 T30
M569 P0.2 S0 D3 H50 V30 ; physical drive 0.2 goes forwards
M915 P0.2 T50
M569 P0.3 S1 D3 H50 V30 ; physical drive 0.3 goes forwards
M915 P0.3 T50
M569 P0.4 S0 D3 H50 V30 ; physical drive 0.4 goes forwards
M915 P0.4 T50
M569 P0.5 S1 D3 H50 V30 ; physical drive 0.5 goes forwards
M915 P0.5 T50
M584 X0.0 Y0.1 Z0.2 E3:5 U4 ; set drive mapping
M350 X16 Y16 U16 Z16 E16:16 I1 ; configure microstepping without interpolation
M92 X80 Y80 U80 Z800 E286.216 :286.216 ; set steps per mm
M566 X480 Y300 U480 Z24 E300:300 ; set maximum instantaneous speed changes (mm/min)
M203 X12000 U12000 Y10000 Z600 E3000:3000 ; set maximum speeds (mm/min)
M201 X1000 U1000 Y500 Z100 E3000:3000 ; set accelerations (mm/s^2)
M906 X850 U850 Y850 Z800 E800:800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
; Axis Limits
M208 X10 Y-3 Z0 U35 S1 ; set axis minima
M208 X335 Y255 Z240 U355 S0 ; set axis maxima
; Endstops ; configure switch-type (e.g. microswitch) endstop for high end on Z via pin null
M574 Y1 S1 P"io1.in"
M574 X1 S1 P"io2.in"
M574 U2 S1 P"Io4.in"
;M915 X S-63 H10 R1 ; Set very sensitive stall detect
;M574 X1 S3 ; configure endstop for stall detection
;M915 X S20 H140 R0 ; Set very sensitive stall detect
;M915 X S-63 H10 R1 ; Set very sensitive stall detect
; Filament Sensoren
M591 D1 P1 C"io5.in" S1
M591 D0 P1 C"io6.in" S1
; Z-Probe
M558 P1 C"io3.in" H5 A5 S0.005 F150 T6000 ; set Z probe type to unmodulated and the dive height + speeds
G31 P500 X10 Y20 Z0.5 ;0.55 Simplify set Z probe trigger value, offset and trigger height
M557 X30:330 Y50:210 P3 ; define mesh grid
; Heaters
M308 S0 P"Temp0" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"Temp1" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin temp1
M950 H1 C"out1" T2 ; create nozzle heater output on out1 and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S340 ; set temperature limit for heater 1 to 340C
M308 S2 P"Temp2" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 2 as thermistor on pin temp2
M950 H2 C"out2" T1 ; create nozzle heater output on out2 and map it to sensor 2
M307 H2 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H2 S340 ; set temperature limit for heater 2 to 340C
; Temp Sensoren
M308 S10 Y"mcu-temp" A"MCU" ; defines sensor 10 as MCU temperature sensor
M308 S11 Y"drivers" A"Duet stepper drivers" ; defines sensor 11 as stepper driver temperature sensor
;M950 F5 C"out6" Q500 ; create fan 2 on pin fan2 and set its frequency
;M106 P5 H3 T40:70 ; set fan 2 value
; Fans
M950 F0 C"vfd" Q500 ; create fan 0 on pin out4 and set its frequency
M106 P0 C"Extruder&Bauteile" S0 H-1
;M950 F5 C"out6" Q500
;M106 P5 C"Board" S0 H-1
M950 F2 C"out3" Q500 ; create fan 0 on pin out4 and set its frequency
M106 P2 C"Filter Lüfter" S0 H-1 Q25000 ; set fan 0 value. Thermostatic control is turned off ; set fan 1 value. Thermostatic control is turned off
M950 F3 C"out5" Q500 ; create fan 2 on pin vfd and set its frequency
M106 P3 C"LED" S150 H-1 ; set fan 2 value. Thermostatic control is turned off
M950 F4 C"out4+out4.tach" Q25000
M106 P4 C"Aktiv Kühlung" S0 H-1
; Create a tool that uses the low end (X) carriage
M563 P0 D0 H1 F0 S"linker Extruder" ; tool 0 uses extruder 0, heater 1 and fan 0
G10 P0 X0 Y0 Z0 S0 R0 ; set tool 0 offsets and temperatures
; Create a tool that uses the high end (U) carriage
M563 P1 D1 H2 X3 F0 S"rechter Extruder" ; tool 1 uses extruder 1, heater 2, fan 2, and maps X to U
G10 P1 Y-0.4 U26.6 Z-0.10 R0 ; set tool 1 offsets and temperatures
; Create a tool that prints 2 copies of the object using both carriages
M563 P2 D0:1 H1:2 X0:3 F0:0 S"Duplicate"; tool 2 uses both extruders, hot end heaters and fans, and maps X to both X and U
G10 P2 X-25 Y0 U-176.3 Z0 S0 R0 ; set tool offsets and temperatures
G10 P2 R0 S0
M567 P2 E1:1 ; set mix ratio 100% on both extruders
;Create a tool that Prints in Mirrior Mode
M563 P3 S"Mirror" H1:2 D0:1 X0:3 F0:0
G10 P3 X-25 Y0 U-176.3 Z0 S0 R0
G10 P3 R0 S-2
; Custom settings are not defined
;Temperatur anpassung MCU
M912 P0 S2
; Miscellaneous
M501 ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
@markz post processing script:
{REPLACE "Material Length" "Filament length"}
@dc42 It was a G1 command in the intro line. The right extruder came too close to the left one. I shortened the movement by 5mm and the message disappeared. Thank you for your explanation
Hello everyone here who helped me. I was able to successfully install a version that was before 2.02. Then the printer could be updated via the Raise software. The whole thing was worth it for me, because now I have the possibility to control it via octoprint for whatever reason. thank you again
@oliof OK thank you.
then it is better to apply it only on the y low and z high axis.
and to work with limit switches on the x and u axis
M291 P"Start.g wird ausgeführt" S0
M98 P"/Macros/SUB/CheckDoor" ;Door open or closed
M561
M106 P3 S0
G4 S1
M106 P3 S25
G4 S1
M106 P3 S0
G4 S1
M106 P3 S25 ;dimme LED for IR Probe
M98 P"/Macros/SUB/Preheat" ;Preheat for Loaded Filament
if !move.axes[0].homed || !move.axes[1].homed || !move.axes[2].homed
G28
G28 Z0
M98 P"/Macros/Buildplate" ;Load Hightmap for Buildplate and Filament
M98 P"config_probe.g"
Wish you all a healthy and better year 2021
The conversion to the duet 3 mini is complete. Just a few things to adjust. Thank you for your help, you are great
@oliof It works perfectly with 2 pieces. Thanks
it works fine now.
here is the gcode if anyone is interested
var errorfix = 0.000 ; constant offset
G31 Z0 ; set Z-offset to Z=0
echo >"0:/sys/config_probe.g" "G31 Z0"
M291 S3 R"Heating up nozzle" P"Wait for the nozzle to reach printing temperatures"
M568 P0 S210 ; set tool 0 (primary hotend) temperature to 210c
T0 ; select tool 0 (primary hotend)
M116 P0 H5 ; wait for temperature to reach within 5c of set temperature
M300 S666 P666 ; beep
M291 S3 R"Automatic Z Offset Calibration" P"Press OK to continue, or CANCEL to abort"
M291 S3 R"Homing axes" P"Remove the puck. The printer will home the X, Y, and Z axises without the puck"
M98 P"config_probe.g" ; Load BLTouch probe settings
M280 P0 S60 I1 ; clear any probe errors
G29 S2 ; cancel mesh bed compensation
G91 ; relative positioning
M913 X50 ; X axis 50% power
G1 H2 Z5 F200 ; lift Z relative to current position
G28 X0 U0 Y0 ; Home X,U and Y axis ; go back a few mm
M913 X100 ; X axis 100% power
G90 ; absolute positioning
G1 X{move.axes[0].min+175} Y{move.axes[1].min+110} F6000 ; move to center
G1 F600 ; reduce speed
G30 ; home Z by probing the bed
G31 Z0 ; set Z-offset to Z=0
M564 H1 S0 ; Negative movements are allowed
G29 S2 ; cancel mesh bed compensation
G90 ; absolute positioning
G1 Z35 ; raise Z to 35mm
M83 ; relative extruder moves
G1 E-5 F300 ; retract 5mm of filament
G4 P0 ; wait for the moves to finish
M291 S3 R"Clean the nozzle" P"The nozzle has been pre-heated. Clean it from any plastic debris"
G1 X100 Y200 F6000 ; go to X100, Y200
G4 P0 ; wait for movements to have stopped
M300 S666 P666 ; beep
M291 S3 P"Place the offset tool below the nozzle and press OK to perform the macro, or CANCEL to abort"
G4 P200 ; wait 200ms
G91 ; relative moves
G1 H1 Z-19 F50 ; move 19mm down, stop when hitting the offset tool (but don't risk crashing the bed)
G92 Z0 ; set current position as Z=0
G4 P200 ; wait 200ms
G1 Z11 F200 ; move up 11mm
G91 ; relative moves
G1 X{sensors.probes[0].offsets[0] * -1} Y{sensors.probes[0].offsets[1] * -1} F1500 ; move nozzle so that BLTouch is in it's position
G90 ; absolute moves
G30 S-3 ; probes Z and adjusts the probe trigger height to match the actual stop height.
G4 P200 ; wait 200ms
G91 ; relative movement
M568 P0 S0 ; set tool 0 temperatures to 0
var Z_auto_offset = {sensors.probes[0].triggerHeight+var.errorfix} ; math to calculate the BLTouch offset
if var.Z_auto_offset < 0.01
M291 S2 R"The nozzle has not touched the puck." P"Please check the guide for troubleshooting"
echo "The nozzle has not touched the puck. Please check the guide for troubleshooting"
echo >"0:/sys/config_probe.g" "G31 Z-3"
elif var.Z_auto_offset >= 0.01 & var.Z_auto_offset < 3.5
echo >"0:/sys/config_probe.g" "G31 Z"^{var.Z_auto_offset}
M291 S2 R"Z-offset has been stored" P"the Z-offset has been stored in the config_probe.g file. Verify the value stored with the value displayed in the console"
echo "the Z-offset has been stored in the config_probe.g file. The Z-offset is", var.Z_auto_offset, "mm. Remove the offset tool and place it back in the box"
elif var.Z_auto_offset >= 3.5
M291 S2 R"Z-Offset is too high" P"Please verify the probe height using the probe-calibration"
echo "Z-Offset is too high. Please verify the probe height using the probe-calibration"
echo >"0:/sys/config_probe.g" "G31 Z-3"
M564 S1 H1 ; Negative movements are forbidden
M300 S666 P666 ; beep
G91 ; relative moves
G1 Z5 ; lift nozzle up 5mm
G90 ; absolute moves
T-1 ; deselect all tools
M18 ; release steppers
@sebkritikel It also seems to me that the outer contour of PS is somewhat distorted. With s3d, each layer lies perfectly on top of the other
@rainy What is decisive for me is what is on the table after printing and with what quality. I don't need painting or other gimmicks if the print result is not good. Anyway, I'm very satisfied with s3d.
@sebkritikel That was indeed the solution. The print has been running without errors so far