Uh wow, that is exactly the problem is, it seems ....
I feel like an idiot now, thanks for the help much appreciated
Uh wow, that is exactly the problem is, it seems ....
I feel like an idiot now, thanks for the help much appreciated
I am struggling with my new Duet3D 3 board I received last week. I am hooking it up instead of my Ramps 1.4 board and managed to boot it up with a Pi4 as the SBC.
I have made all the connectors and connected all my motors to the board (Driver 0 = X, Driver 1 = Y, Driver 2 = ZA, Driver 3 = ZB, Driver 4 = Extruder).
I am somehow getting constant errors on Driver 3 and 5, they either complain about out of phase A/B, or simply do not move the motor. The problem is tho, if i hook the Nema 17 motors up to the other ports they move fine, also swapping using confirmed working cables. I started using driver 5 as I thought hey might be a bad driver, but also driver 5 refusing to run any motor.
I am running the latest 3.0.1-RC3 firmware I think (bit unclear in docs all). What am I doing wrong, could it be that the board is broken? The diagnostics does not seem to indicate any timeout or problems with the driver?
Here is my config:
; Configuration file for Duet 3 (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Sun Mar 01 2020 13:51:27 GMT+0100 (Central European Standard Time)
; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Duet 3" ; set printer name
; Drives
M569 P0.0 S1 ; physical drive 0.0 goes forwards
M569 P0.1 S1 ; physical drive 0.1 goes forwards
M569 P0.2 S1
M569 P0.3 S1 ; physical drive 0.3 goes forwards
M569 P0.4 S1 ; physical drive 0.4 goes forwards
M584 X0.0 Y0.1 Z0.2:0.3 E0.4 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z2560.00 E400 ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
M906 X1000 Y1000 Z1000 E1000 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X300 Y300 Z250 S0 ; set axis maxima
; Endstops
M574 X1 S0 P"io0.in" ; configure active-low endstop for low end on X via pin io0.in
M574 Y1 S0 P"io1.in" ; configure active-low endstop for low end on Y via pin io1.in
M574 Z1 S0 P"io2.in" ; configure active-low endstop for low end on Z via pin io2.in
; Z-Probe
M558 P0 H5 F120 T6000 ; disable Z probe but set dive height, probe speed and travel speed
M557 X15:215 Y15:195 S20 ; define mesh grid
; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
M143 H0 S90 ; set temperature limit for heater 0 to 90C
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M308 S1 P"temp1" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin temp1
M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1
M143 H1 S280 ; set temperature limit for heater 1 to 280C
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
; Fans
M950 F0 C"out3" Q500 ; create fan 0 on pin out3 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"out4" Q500 ; create fan 1 on pin out4 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C