Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Radds + arduino due

    Scheduled Pinned Locked Moved
    Other control boards
    radds
    5
    19
    2.5k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Phaedruxundefined
      Phaedrux Moderator
      last edited by

      No idea. You're in uncharted territory now.

      Z-Bot CoreXY Build | Thingiverse Profile

      1 Reply Last reply Reply Quote 0
      • weed2allundefined
        weed2all
        last edited by

        And how about panel due for radds?on my dedicated duet2 wifi printers I don't use any lcd...i only use the web interface, but since radds is not a duet if I can't have the web interface, I might try the panel due lcd on it...I don't want to be pc dependent...any tutorial for installing panel due?what hardware do I need more beside the panel due of course?

        https://www.thingiverse.com/weed2all/designs

        dc42undefined 1 Reply Last reply Reply Quote 0
        • A Former User?
          A Former User
          last edited by A Former User

          If the cpu has a uart and it configured in the firmware build then you shouldn't need any hardware, just hook up 5v, gnd, rx, tx and enable panel support it in config.g.

          But like wifi, no idea if the radds build has panel due support enabled, you'd have to try or browse the source.

          weed2allundefined 1 Reply Last reply Reply Quote 0
          • weed2allundefined
            weed2all @A Former User
            last edited by

            @bearer it has uart!how to add it to config.g file in order to activate it..

            https://www.thingiverse.com/weed2all/designs

            1 Reply Last reply Reply Quote 0
            • A Former User?
              A Former User
              last edited by

              how about looking for paneldue in the g-code wiki?
              https://duet3d.dozuki.com/Wiki/Gcode#Section_M575_Set_serial_comms_parameters

              you may still find it wont work without the firmware build supporting it, you're still in uncharted waters, beware the kraken etc.

              1 Reply Last reply Reply Quote 0
              • dc42undefined
                dc42 administrators @weed2all
                last edited by

                @weed2all said in Radds + arduino due:

                And how about panel due for radds?on my dedicated duet2 wifi printers I don't use any lcd...i only use the web interface, but since radds is not a duet if I can't have the web interface, I might try the panel due lcd on it...I don't want to be pc dependent...any tutorial for installing panel due?what hardware do I need more beside the panel due of course?

                The RADDS board certainly used to support PanelDue, and AFAIK it still does.

                Duet WiFi hardware designer and firmware engineer
                Please do not ask me for Duet support via PM or email, use the forum
                http://www.escher3d.com, https://miscsolutions.wordpress.com

                1 Reply Last reply Reply Quote 0
                • weed2allundefined
                  weed2all
                  last edited by

                  Ok...so I got the paneldue 5i in my shopping cart!now another question(I know I'm boring with all the question)
                  tmc2208 uart is supported by the reprap firmware on radds?

                  https://www.thingiverse.com/weed2all/designs

                  dc42undefined 1 Reply Last reply Reply Quote 0
                  • dc42undefined
                    dc42 administrators @weed2all
                    last edited by

                    @weed2all said in Radds + arduino due:

                    Ok...so I got the paneldue 5i in my shopping cart!now another question(I know I'm boring with all the question)
                    tmc2208 uart is supported by the reprap firmware on radds?

                    No. In principle you could add it, if you can identify a free pair of UART or USART Tx and RX pins, because there is a TMC2208/2224 driver in RRF that is used in the Duet Maestro firmware build. You would need to add the multiplexer chip to the hardware to allow several TMC2208 chips to be fed by one UART. The SAM3X chip doesn't have the Peripheral DMA Controllers built in to the UARTs that the SAM4 does, so you would also need to adapt the code to use the regular DMAC instead of the PDC.

                    Duet WiFi hardware designer and firmware engineer
                    Please do not ask me for Duet support via PM or email, use the forum
                    http://www.escher3d.com, https://miscsolutions.wordpress.com

                    1 Reply Last reply Reply Quote 0
                    • weed2allundefined
                      weed2all
                      last edited by

                      Wow...thanks for reply...so is a headake...better let it be...thank you...

                      https://www.thingiverse.com/weed2all/designs

                      1 Reply Last reply Reply Quote 0
                      • weed2allundefined
                        weed2all
                        last edited by

                        Does bltouch work with reprap firmware under radds board?

                        https://www.thingiverse.com/weed2all/designs

                        1 Reply Last reply Reply Quote 0
                        • MrsDelishundefined
                          MrsDelish
                          last edited by

                          PanelDUE works fine on a RADDS board, iirc the pins in the connector had to be rearranged to match the top 4 pins in AUX1. I had to solder pins to AUX1 as well.
                          Firmware 2.03 works fine so far 🙂

                          Send: M115
                          Recv: FIRMWARE_NAME: RepRapFirmware for RADDS FIRMWARE_VERSION: 2.03 ELECTRONICS: RADDS 1.5 FIRMWARE_DATE: 2019-06-13b2
                          

                          There is a lot of sdcard juggling between the printer and pc when setting it up.

                          1 Reply Last reply Reply Quote 0
                          • First post
                            Last post
                          Unless otherwise noted, all forum content is licensed under CC-BY-SA