Help! "Error: G30: Z probe 0 not found" upgrading RRF2 -> RRF3
-
Hi!
Recently I've upgraded my Duet board from RRF2 to RRF3. After this upgrade I'm facing an issue with G30 S-1. Sending it gives me error:Error: G30: Z probe 0 not foundI'm using a switch, which is connected to e0 stop. This setup worked fine on RRF2. Right now I have no idea what to do.
Please help! Thanks!Sorry if I posted in a wrong place.
M115
FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 3.1.1 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2020-05-19b2M98 P"config.g"
HTTP is enabled on port 80 FTP is disabled TELNET is disabled Error: Invalid Z probe type 4 Error: Invalid Z probe index Error: Heater 0 not found Error: Heater 2 not found Error: Heater 3 not found Error: Heater 4 not found Error: Heater 5 not found Error: Heater 6 not found Error: Heater 7 not foundconfig.g
; Configuration file for Duet WiFi (firmware version 3) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v3.1.4 on Sun Oct 11 2020 19:02:47 GMT+0200 (Central European Summer Time) ; General preferences G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"AKL Plus" ; set printer name M665 R138.023 L281.462 B105 H260 ; Set delta radius, diagonal rod length, printable radius and homed height M666 X0 Y0 Z0 ; put your endstop adjustments here, or let auto calibration find them ; Network M552 S1 ; enable network M586 P0 S1 ; enable HTTP M586 P1 S0 ; disable FTP M586 P2 S0 ; disable Telnet ; Drives M569 P0 S1 ; physical drive 0 goes forwards M569 P1 S1 ; physical drive 1 goes forwards M569 P2 S1 ; physical drive 2 goes forwards M569 P3 S1 ; physical drive 3 goes forwards M584 X0 Y1 Z2 E3 ; set drive mapping M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation M92 X80.00 Y80.00 Z80.00 E385.00 ; set steps per mm M566 X300 Y300 Z300 E300 ; set maximum instantaneous speed changes (mm/min) M203 X12000 Y12000 Z12000 E12000 ; set maximum speeds (mm/min) M201 X2000.00 Y2000.00 Z2000.00 E2000.00 ; set accelerations (mm/s^2) M906 X1000 Y1000 Z1000 E1000 I30 ; set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Axis Limits M208 Z0 S1 ; set minimum Z ; Endstops M574 X2 S1 P"xstop" ; configure active-high endstop for high end on X via pin xstop M574 Y2 S1 P"ystop" ; configure active-high endstop for high end on Y via pin ystop M574 Z2 S1 P"zstop" ; configure active-high endstop for high end on Z via pin zstop ; Z-Probe M558 P4 C"e0stop" H10 F100 T6000 ; set Z probe type to switch and the dive height + speeds G31 P1000 X0 Y0 Z23.022 ; set Z probe trigger value, offset and trigger height M557 R110 S10 ; define mesh grid ; Heaters M140 H-1 ; disable heated bed (overrides default heater mapping) M143 H1 S280 ; set temperature limit for heater 1 to 280C M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin e0temp M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 0 M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit ; Fans M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency M106 P0 C"PC fan" S0 H-1 ; set fan 0 name and value. Thermostatic control is turned off M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency M106 P1 C"HE fan" S1 H1 T45 ; set fan 1 name and value. Thermostatic control is turned on ; Tools M563 P0 S"hot end" D0 H1 F0 ; define tool 0 G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C ; Custom settings are not defined ; Miscellaneous M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss M501 ; load saved parameters from non-volatile memory T0 ; select first tool -
@BananaMuffin said in Help! "Error: G30: Z probe 0 not found" upgrading RRF2 -> RRF3:
Error: Invalid Z probe type 4
https://duet3d.dozuki.com/Wiki/Gcode#Section_M558_in_RepRapFirmware_Num_3
Z probe types 4, 6 and 7 are no longer supported. Instead, use type 5 (filtered digital) or 8 (unfiltered digital) and use the C parameter to specify the input. Note, if your Z probe is connected to the Z endstop input, in RRF 3.0 on Duet 2 boards only (not in RRF 3.01 and later, and not in RRF 3.0 on Duet 3), that input is by default pre-assigned to be used by the Z endstop, so you must free it up first.
-
Wow, that was a fast reply.
So:
M558 P5 C"e0stop" H10 F100 T6000did the job.
Cheers!
-
What a great first post! It contained all the needed information to provide a quick and accurate solution. I wish they were all like this!
