Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    New firmware 1.19 beta 2

    Scheduled Pinned Locked Moved
    Firmware installation
    18
    70
    9.8k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Kulitorumundefined
      Kulitorum
      last edited by

      So I try to get the machine into AP mode:

      11:45:44.303 : serial: N45 M589 S"DuetWifi" P"Silverspoon" I192.168.1.1*28
      And then M552 S2
      I get:
      11:46:03.063 : WiFi reported error: invalid access point configuration

      1 Reply Last reply Reply Quote 0
      • tomasfundefined
        tomasf
        last edited by

        I don't think AP mode is implemented yet, is it?

        But yeah, I have the same problem joining my network. It just sits there doing nothing, like it can't find the network at all. Signal strength should be fine, and no other devices have any problems joining at all.

        1 Reply Last reply Reply Quote 0
        • Kulitorumundefined
          Kulitorum
          last edited by

          I got it to work by deleting all known networks one at a time and re-add my main wifi.

          1 Reply Last reply Reply Quote 0
          • vhowardundefined
            vhoward
            last edited by

            Beta 6 is actually working with my printer. Just need to figure out how to use the M587 command to delete previous wifi connections so I can re-enter the correct one.

            1 Reply Last reply Reply Quote 0
            • dc42undefined
              dc42 administrators
              last edited by

              @vhoward:

              Beta 6 is actually working with my printer. Just need to figure out how to use the M587 command to delete previous wifi connections so I can re-enter the correct one.

              It's M588 that does that, see https://duet3d.com/wiki/G-code#M588:_Forget_WiFi_host_network.

              Duet WiFi hardware designer and firmware engineer
              Please do not ask me for Duet support via PM or email, use the forum
              http://www.escher3d.com, https://miscsolutions.wordpress.com

              1 Reply Last reply Reply Quote 0
              • dc42undefined
                dc42 administrators
                last edited by

                @Kulitorum:

                So I try to get the machine into AP mode:

                11:45:44.303 : serial: N45 M589 S"DuetWifi" P"Silverspoon" I192.168.1.1*28
                And then M552 S2
                I get:
                11:46:03.063 : WiFi reported error: invalid access point configuration

                Did you use M589 to configure the access point parameter first? See https://duet3d.com/wiki/G-code#M589:_Configure_access_point_parameters. However, I haven't yet tested access point functionality, so it is more than likely that it doesn't work.

                Duet WiFi hardware designer and firmware engineer
                Please do not ask me for Duet support via PM or email, use the forum
                http://www.escher3d.com, https://miscsolutions.wordpress.com

                1 Reply Last reply Reply Quote 0
                • vhowardundefined
                  vhoward
                  last edited by

                  @dc42:

                  @vhoward:

                  Beta 6 is actually working with my printer. Just need to figure out how to use the M587 command to delete previous wifi connections so I can re-enter the correct one.

                  It's M588 that does that, see https://duet3d.com/wiki/G-code#M588:_Forget_WiFi_host_network.

                  Thanks. I will clean it up now. It has been behaving itself so far and just about to complete a 10 hour print.

                  1 Reply Last reply Reply Quote 0
                  • tomasfundefined
                    tomasf
                    last edited by

                    Any plans for a G-code that scans for and replies with available WiFi networks?

                    1 Reply Last reply Reply Quote 0
                    • dc42undefined
                      dc42 administrators
                      last edited by

                      @tomasf:

                      Any plans for a G-code that scans for and replies with available WiFi networks?

                      That requires some thought, because any existing connection to a WiFi network or existing access point that is being provided will have to be terminated in order to do the scan.

                      Duet WiFi hardware designer and firmware engineer
                      Please do not ask me for Duet support via PM or email, use the forum
                      http://www.escher3d.com, https://miscsolutions.wordpress.com

                      1 Reply Last reply Reply Quote 0
                      • vhowardundefined
                        vhoward
                        last edited by

                        Well, It worked for one day. It will still print when I hook up via usb, but the wifi module will not work today. It just reports that the wifi module is idle. I am just going to replace the duet wifi with something else until you make the ethernet module available.

                        1 Reply Last reply Reply Quote 0
                        • First post
                          Last post
                        Unless otherwise noted, all forum content is licensed under CC-BY-SA