daemon.g failed to parse major G-code number (lobal)

blt3dp

Running Duet 3 6HC in SBC mode w/3.5.0-beta.4 (RRF, DSF, DWC) and have a daemon.g setup. Maybe I'm missing something, but I'm receiving this message whenever the daemon.g runs. More specifically, it's line 6 that it mentions.

Here's daemon.g

; daemon.g
if global.ledToggle == 1 && {state.status} == "idle"
    M150 E0 R255 U255 B255 P128 S174 ; white
    set global.ledToggle = 2
elif global.ledToggle >= 1 && {state.status} == "processing"
    M150 E0 R0 U255 B0 P128 S174 ; green
else
    ; do nothing

The global variable ledToggle is defined in config.g

global ledToggle = 0

And it's toggled 1 or 0 via a macro.
Any ideas on what might be the cause?

Also here's an M122

M122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.5.0-beta.4 (2023-06-08 23:41:30) running on Duet 3 MB6HC v1.0 or earlier (SBC mode)
Board ID: 08DGM-9T66A-G63SJ-6JTDL-3SD6P-TS0HA
Used output buffers: 1 of 40 (40 max)
=== RTOS ===
Static ram: 155012
Dynamic ram: 80988 of which 2904 recycled
Never used RAM 103128, free system stack 134 words
Tasks: ACCEL(6,nWait,0.0%,348) SBC(2,rWait:,1.2%,390) HEAT(3,nWait,0.0%,323) Move(4,nWait,3.5%,218) CanReceiv(6,nWait,0.0%,941) CanSender(5,nWait,0.0%,335) CanClock(7,delaying,0.0%,343) TMC(4,nWait,9.2%,61) MAIN(2,running,86.0%,444) IDLE(0,ready,0.0%,30), total 100.0%
Owned mutexes: HTTP(MAIN)
=== Platform ===
Last reset 02:46:14 ago, cause: software
Last software reset at 2023-08-24 16:24, reason: User, Gcodes spinning, available RAM 103032, slot 1
Software reset code 0x6803 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task SBC Freestk 0 n/a
Error status: 0x04
Aux0 errors 0,0,0
MCU temperature: min 38.0, current 38.3, max 38.7
Supply voltage: min 23.9, current 24.0, max 24.0, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.2, current 12.2, max 12.3, under voltage events: 0
Heap OK, handles allocated/used 99/2, heap memory allocated/used/recyclable 2048/1788/1752, gc cycles 10
Events: 0 queued, 0 completed
Driver 0: ok, SG min 0, mspos 280, reads 6760, writes 0 timeouts 0
Driver 1: ok, SG min 0, mspos 917, reads 6759, writes 0 timeouts 0
Driver 2: ok, SG min 0, mspos 583, reads 6760, writes 0 timeouts 0
Driver 3: standstill, SG min 0, mspos 200, reads 6760, writes 0 timeouts 0
Driver 4: standstill, SG min n/a, mspos 8, reads 6760, writes 0 timeouts 0
Driver 5: standstill, SG min n/a, mspos 8, reads 6760, writes 0 timeouts 0
Date/time: 2023-08-24 19:10:33
Slowest loop: 4.28ms; fastest: 0.07ms
=== Storage ===
Free file entries: 20
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, segments created 46, maxWait 767ms, bed compensation in use: none, height map offset 0.000, ebfmin 0.00, ebfmax 1.00
next step interrupt due in 17 ticks, disabled
=== DDARing 0 ===
Scheduled moves 833246, completed 833225, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state 3
=== DDARing 1 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
Heater 0 is on, I-accum = 0.0
Heater 1 is on, I-accum = 0.5
=== GCodes ===
Movement locks held by null, null
HTTP* is doing "M122" in state(s) 0
Telnet is idle in state(s) 0
File* is doing "G1 X-68.708000 Y48.910000 E0.602210" in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0
Queue* is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon* is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
File2* is idle in state(s) 0
Queue2 is idle in state(s) 0
Q0 segments left 1, axes/extruders owned 0x80000007
Code queue 0 is empty
Q1 segments left 0, axes/extruders owned 0x0000000
Code queue 1 is empty
=== Filament sensors ===
Extruder 0 sensor: ok
=== CAN ===
Messages queued 11055, received 0, lost 0, boc 0
Longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 50 (min 50), ts 6142/0/0
Tx timeouts 0,0,6142,0,0,4913 last cancelled message type 30 dest 127
=== SBC interface ===
Transfer state: 5, failed transfers: 0, checksum errors: 0
RX/TX seq numbers: 27704/27704
SPI underruns 0, overruns 0
State: 5, disconnects: 0, timeouts: 0 total, 0 by SBC, IAP RAM available 0x25ce8
Buffer RX/TX: 1836/3284-0, open files: 0
=== Duet Control Server ===
Duet Control Server version 3.5.0-beta.4 (2023-06-09 10:49:49)
File /opt/dsf/sd/gcodes/Saved_G-codes/filename_sanitized.gcode is selected, processing
File:
Buffered code: G1 X-68.708 Y48.91 E0.60221
Buffered code: G1 X-68.708 Y51.787 E0.09021
Buffered code: G1 X-49.501 Y51.787 E0.60221
Buffered code: G1 X-49.501 Y52.254 E0.01462
Buffered code: G1 X-46.624 Y52.254 E0.09021
Buffered code: G1 X-46.624 Y54.664 E0.07559
Buffered code: G1 X-68.708 Y54.664 E0.69242
Buffered code: G1 X-68.708 Y57.075 E0.07558
Buffered code: G1 X-51.445 Y57.075 E0.54125
Buffered code: G1 X-51.445 Y57.542 E0.01463
Buffered code: G1 X-46.462 Y57.542 E0.15625
Buffered code: G10 ; retract
Buffered code: G1 X-5.668 Y57.542 F15000
Buffered code: G11 ; unretract
Buffered code: G1 F4320
Buffered code: G1 X-5.668 Y54.874 E0.08363
Buffered code: G1 X-2.791 Y54.874 E0.09021
Buffered code: G1 X-2.791 Y51.997 E0.09021
Buffered code: G1 X0.086 Y51.997 E0.09021
Buffered code: G1 X0.086 Y49.12 E0.09021
Buffered code: G1 X2.963 Y49.12 E0.09021
Buffered code: G1 X2.963 Y46.243 E0.09021
Buffered code: G1 X5.84 Y46.243 E0.09021
Buffered code: G1 X5.84 Y43.366 E0.09021
Buffered code: G1 X8.717 Y43.366 E0.09021
Buffered code: G1 X8.717 Y40.489 E0.09021
Buffered code: G1 X14.471 Y40.489 E0.18042
Buffered code: G1 X14.471 Y37.612 E0.09021
Buffered code: G1 X22.682 Y37.612 E0.25746
Buffered code: G1 X22.682 Y40.069 E0.07704
Buffered code: G1 X19.805 Y40.069 E0.09021
Buffered code: G1 X19.805 Y42.946 E0.09021
Buffered codes: 1472 bytes total
Code buffer space: 1836
Configured SPI speed: 8000000Hz, TfrRdy pin glitches: 0
Full transfers per second: 53.48, max time between full transfers: 58.8ms, max pin wait times: 45.3ms/7.3ms
Codes per second: 109.58
Maximum length of RX/TX data transfers: 4560/3172

blt3dp

Looks like it only happens when I reload the page.