End stops not working after upgrade to 1.19
-
Firmware 1.20 is current now. Please post your config.g file.
-
Awesome response as usual David. Will do the 1.2 upgrade. In the meantime here is config .g.
; Configuration file for Duet WiFi (firmware version 1.16)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool on Sat Dec 17 2016 11:00:47 GMT+1300 (New Zealand Standard Time); General preferences
M111 S0 ; Debugging off
G21 ; Work in millimetres
G90 ; Send absolute coordinates…
M83 ; ...but relative extruder moves
M555 P2 ; Set firmware compatibility to look like MarlinM667 S1 ; Select CoreXY mode
M208 X0 Y0 Z0 S1 ; Set axis minima
M208 X300 Y300 Z350 S0 ; Set axis maxima; Endstops
M574 X1 Y1 Z0 S0 ; Define active low and unused microswitches
M558 P1 X0 Y0 Z1 H5 F120 T6000 ; Set Z probe type to unmodulated, the axes for which it is used and the probe + travel speeds
G31 P500 X0 Y0 z1.76 ; Set Z probe trigger value, offset and trigger height; Drives
M569 P0 S0 ; Drive 0 goes backwards
M569 P1 S1 ; Drive 1 goes backwards
M569 P2 S1 ; Drive 2 goes forwards
M569 P3 S1 ; Drive 3 goes forwards
M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation
M92 X160 Y160 Z3200 E422 ; Set steps per mm
M566 X900 Y900 Z12 E120 ; Set maximum instantaneous speed changes (mm/min)
M203 X6000 Y6000 Z500 E1200 ; Set maximum speeds (mm/min)
M201 X500 Y500 Z250 E250 ; Set accelerations (mm/s^2)
M906 X1700 Y1700 Z1700 E750 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Heaters
M143 S300 ; Set maximum heater temperature to 260C
;M305 P0 T100000 B3950 R4700 ; Set thermistor + ADC parameters for heater 0
M305 P1 X200 ; Set thermistor + ADC parameters for heater 1 and remap it to channel 200; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C; Network
M550 PMy printer ; Set machine name
M552 P0.0.0.0 S1 ; Enable network and acquire dynamic address via DHCP
M501; Fans
M106 P0 S0.3 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H1 T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on; Custom settings are not configured
-
Thanks. I didn't spot anything wrong in the config file.
Are they optical endstops? Those sometimes leak a little, often due to the carriage not completely blocking the slot, and if they don't have built-in pullup resistors then the external LED+resistor pullups in the endstop circuits may not be sufficient, resulting in no response or a slow response. In an earlier firmware version (1.18 AFAIR) I disabled the internal endstop pullups in the microprocessor to try to resolve a separate issue; but I've re-enabled them in firmware 1.20.
-
The end stops are mechanical except for the IR probe on Z. I have upgraded to 1.2. Now the end stops in Machine properties are hitting but the Z probe has stopped hitting however the red LED on the IR probe is still activating at the right distance from the bed.
-
I should of said end stops still not stopping X and Y axis and z still getting Insufficient axes homed for bed probing error
-
Also getting an error message when connecting on WiFi "Can't open 0:/sys/oem.json to read, error code 4"
-
Also getting an error message when connecting on WiFi "Can't open 0:/sys/oem.json to read, error code 4"
That's normal, and you can ignore that message.
Please run M574 without parameters after a failed X or Y homing attempt and post the response here. You can reduce motor currents for now to avoid damage when homing an axis fails to stop.
What type of switch are they: simple 2-wire microswitches (in which case, why are you using the NO contacts instead of the NC ones), or the 3-wire Makerbot type?
-
Just a thought but it's not this is it (from the upgrade notes for 1.19)….........
Quote
Important! If you use an IR Z probe or some other type that does not need to be deployed, delete the files sys/deployprobe and sys/retractprobe.g if they exist, because they are now called automatically. You can do this in the System Files Editor of the web interface.
...........end of Quote -
Thanks for the input guys. The end stops are 3 wire Makerbot. I am also getting an error on the bed heater.
Error: Temperature reading fault on heater 0: unknown temperature sensor channel
M574 reports Endstop configuration: X:low end unknown type Y: low end unknown type Z: none, -
Decided I had nothing to lose and redid the configuration with the RRF configuration tool. This has sorted out all my problems. Thanks for your time David.
-
I'm sorry I was a little slow in responding. The M574 "unknown type" report was caused by a firmware bug, it should have said "active low switch". This will be fixed i release 1.20.1. The heater 0 problem was caused because you didn't have a M305 command for heater 0 in config.g.
-
Thanks again. Happily printing now.
