• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login

New firmware 1.21RC3 available

Scheduled Pinned Locked Moved
Firmware installation
31
159
23.8k
Loading More Posts
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • undefined
    xnaron
    last edited by 3 Nov 2018, 02:55 11 Mar 2018, 02:31

    I have 2 duet ethernets one is fairly recent while the other is at least a year old. I was running 1.21RC1 and upgraded the older one to RC3 with no issue. However the newer one, when upgraded to RC3, lost ethernet connectivity after the upgrade. I ran M552 and it said something like wifi disabled. I thought maybe I renamed the wrong firmware file so I flashed 1.21RC1 to it via Sam2.17 and it connected to ethernet. I carefully downloaded the combined version of RC3 and renamed it DuetEthernetFirmware.bin and uploaded. It upgraded and did the upgrade again and ethernet again wasn't working so I flashed it back to 1.21RC1 with sam2.17. Any idea why it seems to think this one is a duet wifi?

    1 Reply Last reply Reply Quote 0
    • undefined
      dc42 administrators
      last edited by 11 Mar 2018, 08:42

      Please confirm that it thinks it is a Duet WiFi after installing RC3, by sending M115. If that confirms it, check that the two pins on the Ethernet daughter board connector nearest the edge of the PCB are properly soldered, both on the socket soldered to the Duet and the pins soldered to the daughter board.

      Duet WiFi hardware designer and firmware engineer
      Please do not ask me for Duet support via PM or email, use the forum
      http://www.escher3d.com, https://miscsolutions.wordpress.com

      1 Reply Last reply Reply Quote 0
      • undefined
        garyd9
        last edited by 11 Mar 2018, 09:39

        I still have the issue with it skipping/ignoring M116 commands with RC3. 😞 It really bit me in the rear when I tried a print with a non-heated build plate. (The only way I could get it to print was to completely preheat the nozzle before starting the gcode print.)

        I'll try to come up with some simple gcode file tomorrow.

        "I'm not saying that you are wrong - I'm just trying to fit it into my real world simulated experience."

        1 Reply Last reply Reply Quote 0
        • undefined
          dc42 administrators
          last edited by 11 Mar 2018, 09:46

          If the M116 command is in a tool change file, are you sure that the file is being run? Tool change files are not run if axes have not been homed when you do the tool change.

          Duet WiFi hardware designer and firmware engineer
          Please do not ask me for Duet support via PM or email, use the forum
          http://www.escher3d.com, https://miscsolutions.wordpress.com

          1 Reply Last reply Reply Quote 0
          • undefined
            gideon
            last edited by 11 Mar 2018, 11:33

            hello i just updated my deut to 1.21RC3,
            only now I can not get out of it,
            that you have to change something now only get error messages when I do home y home and z home
            I hereby add my home files
            could someone help me with this what I am doing wrong?

            ; Configuration file for Duet WiFi (firmware version 1.20 or newer)
            ; executed by the firmware on start-up
            ;
            ; generated by RepRapFirmware Configuration Tool on Tue Jan 02 2018 16:42:45 GMT+0100 (West-Europa (standaardtijd))

            ; General preferences
            M111 S0 ; Debugging off
            G21 ; Work in millimetres
            G90 ; Send absolute coordinates…
            M83 ; ...but relative extruder moves
            M555 P2 ; Set firmware compatibility to look like Marlin
            ; Automatic saving after power loss is not enabled

            M667 S1 ; Select CoreXY mode
            M208 X0 Y0 Z0 S1 ; Set axis minima
            M208 X400 Y400 Z550 S0 ; Set axis maxima

            ; Endstops
            ;M574 S1 Z0
            M574 X1 Y1 S0 ; Set active low endstops
            M574 Z1 S2 ; Set endstops controlled by probe
            ;M307 H3 A-1 C-1 D-1 ; bltouch
            ;M558 P5 X0 Y0 Z1 H3 F100 T5000 ; bltouch
            M558 P5 X0 Y0 Z1 F100 T3000 I1 H1
            G31 X0 Y0 Z1.05 P1000 ; bltouch
            M557 X5:395 Y5:395 S95 ; Define mesh grid

            ; Drives
            M569 P0 S1 ; Drive 0 goes forwards
            M569 P1 S1 ; Drive 1 goes forwards
            M569 P2 S0 ; Drive 2 goes forwards
            M569 P3 S1 ; Drive 3 goes forwards
            M350 X16 Y16 Z16 E16 ; Configure microstepping without interpolation
            M92 X80 Y80 Z400 E100 ; Set steps per mm
            M566 X900 Y900 Z12 E120 ; Set maximum instantaneous speed changes (mm/min)
            M203 X6000 Y6000 Z180 E400 ; Set maximum speeds (mm/min)
            M201 X500 Y500 Z250 E250 ; Set accelerations (mm/s^2)
            M906 X1200 Y1200 Z800 E1400 I30 ; Set motor currents (mA) and motor idle factor in per cent
            M84 S30 ; Set idle timeout

            ; Heaters
            M305 P0 T100000 B3988 C0 R4700 ; Set thermistor + ADC parameters for heater 0
            M143 H0 S120 ; Set temperature limit for heater 0 to 120C
            M305 P1 T100000 B3988 C0 R4700 ; Set thermistor + ADC parameters for heater 1
            M143 H1 S280 ; Set temperature limit for heater 1 to 280C

            ; Tools
            M563 P0 D0 H1 ; Define tool 0
            G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
            G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

            ; Network
            M550 PHypercube gideon ; Set machine name
            M552 S1 ; Enable network
            M587 S"gidbeneden" P"gidbeneden" I192.168.0.35 J192.168.0.1 K255.255.255.0 ; Configure access point and IP addresses. You can delete this line once connected
            M586 P0 S1 ; Enable HTTP
            M586 P1 S1 ; Enable FTP
            M586 P2 S1 ; Enable Telnet

            ; Fans
            M106 P0 S0 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
            M106 P1 S0 I0 F500 H-1 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off
            M106 P2 S1 I0 F500 H1 T60:140 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

            ; Custom settings are not configured

            ; homeall.g

            ; Sensorless Homing test file
            M400 ; make sure everything has stopped before we make changes
            M915 X Y S3 F0 R0 ; configure stall detection
            M574 X0 Y0 S2 ; set endstops to use motor stall
            M913 X50 Y50 ; reduce motor current to 50% to prevent belts slipping
            G91 ; use relative positioning
            G1 S2 X-400 Y-400 F3600 ; move right/back 325mm, stopping at the endstop
            G1 X5 Y5 ; move away from home
            ; X or Y is homed at this point, now home the other axis
            G1 X-400 F3600 ; move towards axis minimum
            G1 Y-400 F3600 ; move towards axis minimum
            G1 X1 Y1 ; move away from home
            M400 ; make sure everything has stopped before we reset the motor currents
            M913 X100 Y100 ; motor currents back to 100%
            G90 ; back to absolute positioning
            M574 X1 Y1 S1 ; define active low microswitches

            ; homex.g

            M915 X Y S3 F0 R0 ; configure stall detection
            M574 X1 Y1 S3 ; set endstops to use motor stall
            G1 S2 Z5 F2000 ; lower bed
            M913 X50 Y50 ; reduce motor current to 50% to prevent belts slipping
            G91 ; use relative positioning
            G1 X-400 F3600 S12 ; course home X
            G1 X1 ; move away from end
            G90 ; back to absolute positioning
            M400 ; make sure everything has stopped before we reset the motor currents
            M913 X100 Y100 ; motor currents back to normal
            M574 X1 Y1 S1 ; set endstops back to normal

            ; homey.g

            M915 X Y S3 F0 R0 ; configure stall detection
            M574 X1 Y1 S3 ; set endstops to use motor stall
            G1 S2 Z5 F2000 ; lower bed
            M913 X50 Y50 ; reduce motor current to 50% to prevent belts slipping
            G91 ; use relative positioning
            G1 Y-400 F3600 ; course home Y
            G1 Y1 ; move away from end
            G90 ; back to absolute positioning
            M400 ; make sure everything has stopped before we reset the motor currents
            M913 X100 Y100 ; motor currents back to normal

            ; homez.g
            ; called to home the Z axis
            ;
            T0 ;select tool
            G91 ;relative coordinates
            G1 S2 Z5 F2000 ;lower bed
            G4 P500 ;wait for the bed to lower
            G90 ;absolute positioning
            G1 X200 Y200 F3000 ;move to center
            ;M401 ;deploy the probe
            G30 ;calibrate Z-axis
            ;M402 ;Retract Probe

            1 Reply Last reply Reply Quote 0
            • undefined
              dc42 administrators
              last edited by 11 Mar 2018, 11:57

              When upgrading firmware you should always read the upgrade notes first. You will find the solution there.

              Duet WiFi hardware designer and firmware engineer
              Please do not ask me for Duet support via PM or email, use the forum
              http://www.escher3d.com, https://miscsolutions.wordpress.com

              1 Reply Last reply Reply Quote 0
              • undefined
                gideon
                last edited by 11 Mar 2018, 12:10

                @dc42:

                When upgrading firmware you should always read the upgrade notes first. You will find the solution there.

                I have the https://github.com/dc42/RepRapFirmware/blob/dev/WHATS_NEW.md
                read only I do not find out what I have to change where
                therefore the question,

                1 Reply Last reply Reply Quote 0
                • undefined
                  dc42 administrators
                  last edited by 11 Mar 2018, 12:20

                  I'm sorry, as you said you had homing issues I assumed you hadn't read the notes.

                  I can see the following errors in your homing files:

                  G1 S2 X-400 Y-400 F3600 ; move right/back 325mm, stopping at the endstop

                  S2 should be S1 in that line.

                  ; X or Y is homed at this point, now home the other axis
                  G1 X-400 F3600 ; move towards axis minimum
                  G1 Y-400 F3600 ; move towards axis minimum

                  Both those lines need S1.

                  G1 X-400 F3600 S12 ; course home X

                  Change S12 to S1

                  G1 Y-400 F3600 ; course home Y

                  Add S1 to that line

                  Duet WiFi hardware designer and firmware engineer
                  Please do not ask me for Duet support via PM or email, use the forum
                  http://www.escher3d.com, https://miscsolutions.wordpress.com

                  1 Reply Last reply Reply Quote 0
                  • undefined
                    gideon
                    last edited by 11 Mar 2018, 12:48

                    thanks

                    1 Reply Last reply Reply Quote 0
                    • undefined
                      dc42 administrators
                      last edited by 11 Mar 2018, 13:01

                      I have just released firmware 1.21RC4 at https://github.com/dc42/RepRapFirmware/releases/tag/1.21RC4. Those of you using RC3, please try RC4 and report any new or continuing issues in the thread I am about to create for that release.

                      Duet WiFi hardware designer and firmware engineer
                      Please do not ask me for Duet support via PM or email, use the forum
                      http://www.escher3d.com, https://miscsolutions.wordpress.com

                      1 Reply Last reply Reply Quote 0
                      159 out of 159
                      • First post
                        159/159
                        Last post
                      Unless otherwise noted, all forum content is licensed under CC-BY-SA