Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Duet3 config with limit on 7 temp inputs

    Scheduled Pinned Locked Moved Solved
    Beta Firmware
    4
    17
    743
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • RobMinkundefined
      RobMink @dc42
      last edited by

      @dc42 I wish it was the case. I have tried that, and just tried it again, and alas, when I run M308 SN where N is 4-7 I get errors, also, now I am getting two sensors on the 2nd expansion board to read 2000C

      1 Reply Last reply Reply Quote 0
      • dc42undefined
        dc42 administrators @RobMink
        last edited by dc42

        @RobMink said in Duet3 config with limit on 7 temp inputs:

        M308 S0 P"0.temp0" Y"thermistor" T100000 A"Bed"
        M308 S1 P"1.temp0" Y"thermistor" T100000 A"Head0"
        M308 S2 P"1.temp1" Y"thermistor" T100000 A"Head1"
        M308 S3 P"1.temp2" Y"thermistor" T100000 A"Head2"
        M308 S4 P"2.temp0" Y"thermistor" T100000 A"Head3"
        M308 S5 P"0.temp1" Y"thermistor" T100000 A"Head4"
        M308 S6 P"0.temp2" Y"thermistor" T100000 A"Head5"
        M308 S7 P"3.temp1" Y"thermistor" T100000 A"Test"

        I don't get any errors when I run that sequence, but there is something not quite right:

        26/12/2019, 14:37:52 	M308 S8
Error: Sensor 8 does not exist
26/12/2019, 14:37:48 	M308 S7
Sensor 7 type Thermistor using pin 3.temp1, last error: sensor open circuit, T:100000.0 B:4388.0 C:0.00e+0 R:2200.0
26/12/2019, 14:37:45 	M308 S6
Sensor 6 (Head5) type Thermistor using pin temp2, reading -273.1, last error: sensor open circuit, T:100000.0 B:4388.0 C:0.00e+0 R:2200.0 L:0 H:0
26/12/2019, 14:37:43 	M308 S5
Sensor 5 (Head4) type Thermistor using pin temp1, reading -273.1, last error: sensor open circuit, T:100000.0 B:4388.0 C:0.00e+0 R:2200.0 L:0 H:0
26/12/2019, 14:37:41 	M308 S4
Sensor 4 type Thermistor using pin 2.temp0, last error: sensor open circuit, T:100000.0 B:4388.0 C:0.00e+0 R:2200.0
26/12/2019, 14:37:40 	M308 S3
Sensor 3 type Thermistor using pin 1.temp2, last error: sensor open circuit, T:100000.0 B:4388.0 C:0.00e+0 R:2200.0
26/12/2019, 14:37:38 	M308 S2
Sensor 2 type Thermistor using pin 1.temp1, last error: sensor open circuit, T:100000.0 B:4388.0 C:0.00e+0 R:2200.0
26/12/2019, 14:37:36 	M308 S1
Sensor 1 type Thermistor using pin 1.temp0, last error: success, T:100000.0 B:4388.0 C:0.00e+0 R:2200.0
26/12/2019, 14:37:32 	M308 S0
Sensor 0 (Bed) type Thermistor using pin temp0, reading -273.1, last error: sensor open circuit, T:100000.0 B:4388.0 C:0.00e+0 R:2200.0 L:0 H:0

        When i query the sensors individually, it only prints the sensor name and current reading for sensors connected to the main board. I will look into it.

        Duet WiFi hardware designer and firmware engineer
        Please do not ask me for Duet support via PM or email, use the forum
        http://www.escher3d.com, https://miscsolutions.wordpress.com

        dc42undefined 1 Reply Last reply Reply Quote 0
        • dc42undefined
          dc42 administrators @dc42
          last edited by dc42

          I also tried running the second sequence:

          M308 S0 P"0.temp0" Y"thermistor" T100000 A"Bed"
M308 S1 P"1.temp0" Y"thermistor" T100000 A"Head0"
M308 S2 P"1.temp1" Y"thermistor" T100000 A"Head1"
M308 S3 P"1.temp2" Y"thermistor" T100000 A"Head2"
M308 S4 P"2.temp0" Y"thermistor" T100000 A"Head3"
M308 S5 P"2.temp1" Y"thermistor" T100000 A"Head4"
M308 S6 P"2.temp2" Y"thermistor" T100000 A"Head5"
M308 S7 P"3.temp1" Y"thermistor" T100000 A"Test"

          That works for me too.

          Are you sure that you don't have any other M308 commands earlier in config.g?

          Duet WiFi hardware designer and firmware engineer
          Please do not ask me for Duet support via PM or email, use the forum
          http://www.escher3d.com, https://miscsolutions.wordpress.com

          1 Reply Last reply Reply Quote 0
          • RobMinkundefined
            RobMink
            last edited by

            Here is my entire config.g

            ; Config for piper2v2 with tool changing - RAM - 13 heads

; General preferences
G90                             ; Send absolute coordinates...
M83                             ; ...but relative extruder moves

; Network
M550 P"Duet3"                   ; Set machine name
M552 S1                         ; Enable network
M586 P0 S1                      ; Enable HTTP
M586 P1 S0                      ; Disable FTP
M586 P2 S0                      ; Disable Telnet

; Drives
M584 X0.0 Y0.1 Z0.2:0.3:0.4:0.5 E1.0:1.1:1.2:2.0:2.1:2.2                ; Map Drives to Axis
M669 K1                         ; Select CoreXY mode
M564 H0				; Allow axis movement prior to homing
M569 P0 S0 V118                 ; Drive 0 goes backwards, Stealthchop2 till about 78 mm/sec
M569 P1 S1 V118                 ; Drive 1 goes forwards, Stealthchop2 till about 78 mm/sec
M569 P2 S1 V118                 ; Drive 2 goes forwards, Stealthchop2 till about 78 mm/sec	;xmax ymin Z
M569 P3 S0 V118                 ; Drive 3 goes backwards, Stealthchop2 till about 78 mm/sec   ;XMIN YMIN Z
M569 P4 S0 V118			;XMAX, YMAX Z
M569 P5 S0 V118			;X0,YMAX Z
M350 X16 Y16 Z16 E16 I1         ; Configure microstepping with interpolation
M92 X80 Y80 Z400 E784	        ; Set steps per mm
M566 X60 Y60 Z24 E1200          ; Set maximum jerk (mm/min)
M203 X30000 Y30000 Z1500 E800   ; Set maximum speeds (mm/min)
M201 X900 Y900 Z300 E1000 I1    ; Set accelerations (mm/s^2)
M906 X1000 Y1000 Z1800 E1500 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30                         ; Set idle timeout

; Tool
M563 P0 D0 H1 F0 S"Extruder0"    ; Define tool 0
G10 P0 X0 Y0 Z0                 ; Set tool 0 axis offsets
G10 P0 R0 S0                    ; Set initial tool 0 active and standby temperatures to 0C

M563 P1 D1 H2 F1 S"Extruder1"    ; Define tool 1
G10 P1 X0 Y0 Z0                 ; Set tool 1 axis offsets
G10 P1 R0 S0                    ; Set initial tool 1 active and standby temperatures to 0C

M563 P2 D2 H3 F2 S"Extruder2"    ; Define tool 2
G10 P2 X0 Y0 Z0                 ; Set tool 2 axis offsets
G10 P2 R0 S0                    ; Set initial tool 2 active and standby temperatures to 0C

M563 P3 D3 H4 F3 S"Extruder3"    ; Define tool 3
G10 P3 X0 Y0 Z0                 ; Set tool 2 axis offsets
G10 P3 R0 S0                    ; Set initial tool 2 active and standby temperatures to 0C

M563 P4 D4 H5 F4 S"Extruder4"    ; Define tool 4
G10 P4 X0 Y0 Z0                 ; Set tool 2 axis offsets
G10 P4 R0 S0                    ; Set initial tool 2 active and standby temperatures to 0C

M563 P5 D5 H6 F5 S"Extruder5"    ; Define tool 5
G10 P5 X0 Y0 Z0                 ; Set tool 2 axis offsets
G10 P5 R0 S0                    ; Set initial tool 2 active and standby temperatures to 0C


; Fans
M950 F0 C"1.out6"
M106 P0 S1 H1 T45 C"Extruder0"       ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M950 F1 C"1.out7"
M106 P1 S1 H2 T45 C"Extruder1"       ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on
M950 F2 C"1.out8"
M106 P2 S1 H3 T45 C"Extruder2"       ; Set fan 3 value, PWM signal inversion and frequency. Thermostatic control is turned on
M950 F3 C"2.out6"
M106 P3 S1 H4 T45 C"Extruder3"       ; Set fan 4 value, PWM signal inversion and frequency. Thermostatic control is turned on
M950 F4 C"2.out7"
M106 P4 S1 H5 T45 C"Extruder4"       ; Set fan 5 value, PWM signal inversion and frequency. Thermostatic control is turned on
M950 F5 C"2.out8"
M106 P5 S1 H6 T45 C"Extruder5"       ; Set fan 6 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 A"Bed"
M308 S1 P"1.temp0" Y"thermistor" T100000 A"Head0"
M308 S2 P"1.temp1" Y"thermistor" T100000 A"Head1"
M308 S3 P"1.temp2" Y"thermistor" T100000 A"Head2"
M308 S4 P"2.temp0" Y"thermistor" T100000 A"Head3"
M308 S5 P"2.temp1" Y"thermistor" T100000 A"Head4"
M308 S6 P"2.temp2" Y"thermistor" T100000 A"Head5"
M308 S7 P"3.temp1" Y"thermistor" T100000 A"Test"
M950 H0 C"out0" T0                ; heater 0 
M950 H1 C"1.out0" T1              ; heater 1 
M950 H2 C"1.out1" T2              ; heater 2 
M950 H3 C"1.out2" T3              ; heater 3 
M950 H4 C"2.out0" T4              ; heater 4 
M950 H5 C"2.out1" T5              ; heater 5 
M950 H6 C"2.out2" T6              ; heater 6 


; Pressure Advance
M572 D0 S0.074

; Axis Limits
M208 X0 Y0 Z0 S1                ; Set axis minima
M208 X950 Y950 Z600 S0          ; Set axis maxima

; Endstops

M574 X1 P"!io1.in" S1                   
M574 Y1 P"!io2.in" S1

            as you can see it is a work in progress.

            Thanks again for looking at this!

            1 Reply Last reply Reply Quote 0
            • RobMinkundefined
              RobMink
              last edited by RobMink

              Ok, so I did a little more troubleshooting. Bear with me here...

              I cut the config to just the following.

              ;Heaters

M308 S0 P"temp0" Y"thermistor" T100000 A"Bed"
M308 S1 P"1.temp0" Y"thermistor" T100000 A"Head0"
M308 S2 P"1.temp1" Y"thermistor" T100000 A"Head1"
M308 S3 P"1.temp2" Y"thermistor" T100000 A"Head2"
M308 S4 P"2.temp0" Y"thermistor" T100000 A"Head3"
M308 S5 P"2.temp1" Y"thermistor" T100000 A"Head4"
M308 S6 P"2.temp2" Y"thermistor" T100000 A"Head5"
M308 S7 P"3.temp0" Y"thermistor" T100000 A"Test"

M950 H0 C"0.out1" T0  ;Bed heater
M950 H1 C"1.out0" T1  ;Extruder0
M950 H2 C"1.out1" T2  ;Extruder1
M950 H3 C"1.out2" T3  ;Extruder2
;M950 H4 C"2.out0" T4  ;Extruder3
;M950 H5 C"2.out1" T5  ;Extruder4
;M950 H6 C"2.out2" T6  :Extruder5

              creates no error, but when I un-comment out the last few lines....

              
;Heaters

M308 S0 P"temp0" Y"thermistor" T100000 A"Bed"
M308 S1 P"1.temp0" Y"thermistor" T100000 A"Head0"
M308 S2 P"1.temp1" Y"thermistor" T100000 A"Head1"
M308 S3 P"1.temp2" Y"thermistor" T100000 A"Head2"
M308 S4 P"2.temp0" Y"thermistor" T100000 A"Head3"
M308 S5 P"2.temp1" Y"thermistor" T100000 A"Head4"
M308 S6 P"2.temp2" Y"thermistor" T100000 A"Head5"
M308 S7 P"3.temp0" Y"thermistor" T100000 A"Test"

M950 H0 C"0.out1" T0  ;Bed heater
M950 H1 C"1.out0" T1  ;Extruder0
M950 H2 C"1.out1" T2  ;Extruder1
M950 H3 C"1.out2" T3  ;Extruder2
M950 H4 C"2.out0" T4  ;Extruder3
M950 H5 C"2.out1" T5  ;Extruder4
M950 H6 C"2.out2" T6  ;Extruder5

              creates an error.

              12/26/2019, 2:14:33 PM Warning: Sensor number 5 has not been defined
              12/26/2019, 2:14:33 PM Error: M308: Pin 2.temp1 is not free
              12/26/2019, 2:14:33 PM Error: M308: Pin 2.temp2 is not free
              12/26/2019, 2:14:33 PM Warning: Sensor number 6 has not been defined

              And every time I update the config I shut down the pi and cut all power for 20 seconds right now, just for grins.

              1 Reply Last reply Reply Quote 1
              • dc42undefined
                dc42 administrators
                last edited by

                Thanks, I have reproduced that.

                Duet WiFi hardware designer and firmware engineer
                Please do not ask me for Duet support via PM or email, use the forum
                http://www.escher3d.com, https://miscsolutions.wordpress.com

                dc42undefined 1 Reply Last reply Reply Quote 0
                • dc42undefined
                  dc42 administrators @dc42
                  last edited by

                  I found the problem. For now, don't assign heater numbers greater than 5 to ports on expansion boards. Will be fixed in RC2.

                  Duet WiFi hardware designer and firmware engineer
                  Please do not ask me for Duet support via PM or email, use the forum
                  http://www.escher3d.com, https://miscsolutions.wordpress.com

                  1 Reply Last reply Reply Quote 0
                  • RobMinkundefined
                    RobMink
                    last edited by

                    Nice work, thank you!

                    1 Reply Last reply Reply Quote 0
                    • dc42undefined
                      dc42 administrators
                      last edited by

                      There are new builds of Duet 3 main and expansion board firmware at https://www.dropbox.com/sh/3azy1njy3ayjsbp/AACquxr2m00eV568RZg5QG5wa?dl=0 with this fixed.

                      Duet WiFi hardware designer and firmware engineer
                      Please do not ask me for Duet support via PM or email, use the forum
                      http://www.escher3d.com, https://miscsolutions.wordpress.com

                      1 Reply Last reply Reply Quote 1
                      • RobMinkundefined
                        RobMink
                        last edited by

                        Confirmed Fixed.

                        1 Reply Last reply Reply Quote 0
                        • First post
                          Last post
                        Unless otherwise noted, all forum content is licensed under CC-BY-SA