Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Configuration problems

    Scheduled Pinned Locked Moved
    Firmware installation
    3
    47
    1.7k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • fcwiltundefined
      fcwilt @Dave Parry
      last edited by

      @dave-parry said in Configuration problems:

      It homes ok but I still get
      G28
      Error: G0/G1: target position not reachable from current position

      Even with that change I suggested?

      Curious.

      Frederick

      Printers: A FT-5 with the 713 upgrade bits, a custom MarkForged style, a small Utilmaker style, a small CoreXY from kit and a E3D MS/TC setup. Various hotends. Using Duets (2 and 3) running 3.4.6

      1 Reply Last reply Reply Quote 0
      • Dave Parryundefined
        Dave Parry
        last edited by Dave Parry

        sorted that out Frederick, the default end stop setting says
        active high endstop switch but X1 is low end it needs to be X2

        1 Reply Last reply Reply Quote 1
        • Dave Parryundefined
          Dave Parry
          last edited by Dave Parry

          Just need to sort fan control not showing and M106 not doing anything either. Think it's because they havent been properly configured.

          fcwiltundefined 1 Reply Last reply Reply Quote 0
          • fcwiltundefined
            fcwilt @Dave Parry
            last edited by

            @dave-parry said in Configuration problems:

            Just need to sort fan control not showing

            Need to see you most recent fan code. It may be still back at v2 syntax.

            Frederick

            Printers: A FT-5 with the 713 upgrade bits, a custom MarkForged style, a small Utilmaker style, a small CoreXY from kit and a E3D MS/TC setup. Various hotends. Using Duets (2 and 3) running 3.4.6

            1 Reply Last reply Reply Quote 0
            • Dave Parryundefined
              Dave Parry
              last edited by

              Think your right

              ; Fans
              M106 P0 S0 I0 F500 H-1 C"Part Clg" ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
              M106 P1 S0 I0 F500 H-1 C"Bed Clg" ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off

              fcwiltundefined 1 Reply Last reply Reply Quote 0
              • fcwiltundefined
                fcwilt @Dave Parry
                last edited by

                @dave-parry said in Configuration problems:

                Think your right

                ; Fans
                M106 P0 S0 I0 F500 H-1 C"Part Clg" ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
                M106 P1 S0 I0 F500 H-1 C"Bed Clg" ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off

                Yes - that's v2 syntax.

                Here is my code for two fans:

                ; ****************************************************************************************************
; cooling fans
; -- P# is fan, S# is speed (0 to 255 or 0.0 to 1.0) H# means turn on fan when heater H# temp hits T#
; -- H-1 means no thermostatic control
; ****************************************************************************************************

M950 F0 C"fan0" Q500        ; create fan (F), pin name (C), frequency (Q)
M106 P0 C"Part" S0 H-1      ; set fan (P), name (C), speed (S), thermostatic control off (H)

M950 F1 C"fan1" Q500        ; create fan (F), pin name (C), frequency (Q)
M106 P1 C"Hotend" S1 H1 T45 ; set fan (P), name (C), speed (S), thermostatic control on (H & T)

                Printers: A FT-5 with the 713 upgrade bits, a custom MarkForged style, a small Utilmaker style, a small CoreXY from kit and a E3D MS/TC setup. Various hotends. Using Duets (2 and 3) running 3.4.6

                1 Reply Last reply Reply Quote 0
                • Dave Parryundefined
                  Dave Parry
                  last edited by Dave Parry

                  @fcwilt said in Configuration problems:

                  M950 F0 C"fan0" Q500 ; create fan (F), pin name (C), frequency (Q)

                  Have got them working with this

                  M950 F0 C"fan0"
                  M950 F1 C"fan1"
                  M106 P0 S0 I0 F500 H-1 C"Part Clg" ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
                  M106 P1 S0 I0 F500 H-1 C"Bed Clg"

                  But have tool fan on there as well which also starts part fan

                  1 Reply Last reply Reply Quote 0
                  • Dave Parryundefined
                    Dave Parry
                    last edited by

                    Tried rem ing out fan0 but then tool fan controls do nothing

                    1 Reply Last reply Reply Quote 0
                    • Dave Parryundefined
                      Dave Parry
                      last edited by

                      Just noticed that the tool fan shows when the hot end is active and when hot end is off or standby is hidden.
                      I either need to hide it completely or get rid of the part fan control but have the tool fan control that fan

                      fcwiltundefined 1 Reply Last reply Reply Quote 0
                      • fcwiltundefined
                        fcwilt @Dave Parry
                        last edited by

                        @dave-parry said in Configuration problems:

                        Just noticed that the tool fan shows when the hot end is active and when hot end is off or standby is hidden.
                        I either need to hide it completely or get rid of the part fan control but have the tool fan control that fan

                        That tool fan display is controlled by the DWC.

                        It's just a way of having a single consistently named control in those cases where you might have multiple tools each with their own fan.

                        You can control the visibility of the actual part fan from the DWC.

                        Frederick

                        Printers: A FT-5 with the 713 upgrade bits, a custom MarkForged style, a small Utilmaker style, a small CoreXY from kit and a E3D MS/TC setup. Various hotends. Using Duets (2 and 3) running 3.4.6

                        1 Reply Last reply Reply Quote 0
                        • Dave Parryundefined
                          Dave Parry
                          last edited by

                          Frederick,
                          Can you tell me where the conrol for fan visibilty is, because I cant see it.
                          also Thanks for your great patience and help.

                          fcwiltundefined 1 Reply Last reply Reply Quote 0
                          • Dave Parryundefined
                            Dave Parry
                            last edited by

                            Found it. I was looking on the dashboard and its on the status.

                            1 Reply Last reply Reply Quote 1
                            • fcwiltundefined
                              fcwilt @Dave Parry
                              last edited by

                              @dave-parry said in Configuration problems:

                              Frederick,
                              Can you tell me where the conrol for fan visibilty is, because I cant see it.
                              also Thanks for your great patience and help.

                              This is visible when you have selected the Job/Status display in the DWC.

                              Fan Visibilty.jpg

                              See the item "Change Visibility"?

                              Frederick

                              Printers: A FT-5 with the 713 upgrade bits, a custom MarkForged style, a small Utilmaker style, a small CoreXY from kit and a E3D MS/TC setup. Various hotends. Using Duets (2 and 3) running 3.4.6

                              1 Reply Last reply Reply Quote 0
                              • Dave Parryundefined
                                Dave Parry
                                last edited by

                                Yours looks different to mine. I dont have no fans option, just lists all the fans with a tick box for each. Also jobs and status are seperate tags.

                                fcwiltundefined 1 Reply Last reply Reply Quote 0
                                • fcwiltundefined
                                  fcwilt @Dave Parry
                                  last edited by

                                  @dave-parry said in Configuration problems:

                                  Yours looks different to mine. I dont have no fans option, just lists all the fans with a tick box for each. Also jobs and status are seperate tags.

                                  Like this?

                                  Fan Visibilty.jpg

                                  Status is under the Job category - that what I meant by Job/Status

                                  Printers: A FT-5 with the 713 upgrade bits, a custom MarkForged style, a small Utilmaker style, a small CoreXY from kit and a E3D MS/TC setup. Various hotends. Using Duets (2 and 3) running 3.4.6

                                  1 Reply Last reply Reply Quote 0
                                  • Dave Parryundefined
                                    Dave Parry
                                    last edited by Dave Parry

                                    I understand, and if I turn all the fans off in the tick box I get no fans message, Think I'm getting tired, Will carry on with calibration tomorrow. Thank you for your help. would'nt have got there without it.

                                    1 Reply Last reply Reply Quote 1
                                    • First post
                                      Last post
                                    Unless otherwise noted, all forum content is licensed under CC-BY-SA