Duet 3 6HC max pwm is only 3.8V
-
Im trying to connect a vfd to out 9 using this pwm converter https://www.amazon.com/dp/B091B6LGXB?ref=ppx_yo2ov_dt_b_fed_asin_title
When i measure the pwm signal it is only putting out 3.8 volts when i turn the spindle on at the max rpm of 24,000. The voltage out is only getting to 9V.
; Configuration file for RepRapFirmware on Duet 3 Main Board 6HC ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v3.5.4 on Mon Sep 09 2024 22:47:07 GMT-0600 (Mountain Daylight Time) ; General G90 ; absolute coordinates M83 ; relative extruder moves M550 P"Duet3CNC" ; set hostname M453 ; select CNC mode ; Accessories M575 P1 S0 B57600 ; configure PanelDue support ; Smart Drivers M569 P0.0 S1 D2 ; driver 0.0 goes backwards (X axis) M569 P0.1 S0 D2 ; driver 0.1 goes backwards (Y axis) M569 P0.2 S1 D2 ; driver 0.2 goes forwards (Z axis) M569 P0.3 S1 D2 ; driver 0.3 goes forwards (U or Y2 axis) M569 P0.4 S1 D2 ; driver 0.4 goes forwards (V or Z2 axis) ; Motor Idle Current Reduction M906 I30 ; set motor current idle factor M84 S1000 ; set motor current idle timeout ; Axis M669 K0 ; set Cartesian kinematics M584 X0.0 Y0.1:0.3 Z0.2:0.4 U0.3 V0.4 P3 ; U=Y2 V=Z2 set axis mapping M350 X16 Y16 Z16 U16 V16 I1 ; configure microstepping with interpolation M906 X1205.2 Y1100.4 Z1100.4 U1100.4 V1100.4 ; set axis driver currents M92 X100.067 Y100.067 Z400 U100.067 V400 ; configure steps per mm M566 X60 Y60 Z60 U60 V60 ; set maximum instantaneous speed changes (mm/min) M203 X12000 Y12000 Z3000 U12000 V3000 ; set maximum speeds (mm/min) M201 X600 Y600 Z60 U600 V60 ; set accelerations (mm/s^2) ; Axis Limits M208 X0 Y0 Z-100 U0 V-100 S1 ; set axis minimum M208 X1252 Y2467.8 Z140 U2467.8 V140 S0 ; set axis maximum ; Endstops M574 X1 S1 P"io1.in" ; configure active-high endstop for low end on X via pin io2.in M574 Y1 S1 P"io2.in+io3.in" ; configure active-high endstop for low end on Y via pin io2.in M574 Z2 S1 P"io4.in+io5.in" ; configure active-high endstop for high end on Z via pin io4.in ;M574 U1 S1 P"io3.in" ; configure active-high endstop for low end on U (Y2) via pin io3.in ;M574 V2 S1 P"io5.in" ; configure active-high endstop for high end on V (Z2) via pin io5.in ; Probes M558 P5 C"!io6.in" H5 F120 T6000 ; configure analog probe via slot #0 G31 P850 X-10 Y-10 Z5.89 ; set Z probe trigger value, offset and trigger height ;M574 V2 S1 P"io5.in" ;M666 Y+2 ; move Y1 motor -1.5 from block to adjust for square ; Heaters M140 H-1 ; disable heated bed (overrides default heater mapping) M141 H-1 ; Tools M453 ; Set to CNC mode M950 R0 C"out9" Q1000 L0:24000 K1 ; configure spindle #0 M563 P1 S"Makita R0701C" R0 F0 ; create tool #0 ; Lasers M950 P2 C"out4" ; air Assist solenoid ; Laser offset from spindle is X - 57.5 Y - -49.10 M452 C"io7.out" R255 F500 S1 ; configure Laser port ;M563 P2 S"Laser" ;M452 ; LED Lighting ;M950 P3 c"out1" Q500 M950 F0 c"out1" Q500 ;M42 P3 S1 M106 P0 S0 H-1 C"LEDs" ;M563 P0 D-0 R0 ; tool 0 uses extruder 0, heater 1 and fan 0 ; Emergency Stop M950 J1 C"io8.in" M581 T1 P0:1 S1 R0 ;M582 T1 ;M42 P2 S1 ; Tools M563 P2 S"Laser" F0 ;M568 P0 F0 ; set initial tool #0 active and standby temperatures to 0C ; Miscellaneous ;M452 ; select Laser mode T0 ; select first tool M308 S10 Y"mcu-temp" A"MCU" M308 S11 P"DRIVER_0" Y"drivers" A"X Driver" M308 S12 P"DRIVER_1" Y"drivers" A"Y Driver" M308 S13 P"DRIVER_3" Y"drivers" A"Y1 Driver" M308 S14 P"DRIVER_2" Y"drivers" A"Z Driver" M308 S15 P"DRIVER_4" Y"drivers" A"Z1 Driver"
What am i missing?
Thanks