@infiniteloop oh shit.....10x checked and overlooked^^

Many thanks for the help. Now it seems to be working.

@infiniteloop oh shit.....10x checked and overlooked^^

Many thanks for the help. Now it seems to be working.

@infiniteloop

Hello and thank you for your help, I checked the wiring and it should fit. I've also tested if I swap the two outer contacts, but then the sensor doesn't even flash anymore, so it should fit the way it's connected. The error stays the same. When I turn on the printer, the sensor also flashes 3x as it should and when I push the filament through the sensor by hand, it also registers this and flickers or lights up almost permanently as it should.!

nobody an idea?

Hello, i dont get the Magnetic Filamensensor running right...

This error comes every 10seconds and the Printer gets paused:

Printing paused Filament error on extruder 0: noDataReceived

My M591 D0 shows this:

Duet3D rotating magnet filament monitor v1 on pin e0stop, enabled, sensitivity 28.80mm/rev, allow 60% to 160%, check printing moves every 3.0mm, no data received

What do i wrong please?

M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.4.6 (2023-07-21 14:08:28) running on Duet WiFi 1.02 or later
Board ID: 08DGM-95BNL-MGPSN-6JKD2-3SJ6K-90YBY
Used output buffers: 1 of 26 (24 max)
=== RTOS ===
Static ram: 23896
Dynamic ram: 79580 of which 0 recycled
Never used RAM 5196, free system stack 114 words
Tasks: NETWORK(notifyWait,14.8%,242) HEAT(notifyWait,0.0%,333) Move(notifyWait,0.2%,292) MAIN(running,84.8%,436) IDLE(ready,0.2%,30), total 100.0%
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:20:27 ago, cause: power up
Last software reset at 2023-08-23 13:22, reason: User, GCodes spinning, available RAM 5452, slot 2
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x08
Aux0 errors 0,1,0
Step timer max interval 0
MCU temperature: min 36.1, current 41.9, max 42.2
Supply voltage: min 24.1, current 24.3, max 24.7, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 99/1, heap memory allocated/used/recyclable 2048/40/0, gc cycles 0
Events: 6 queued, 6 completed
Driver 0: standstill, SG min 39
Driver 1: standstill, SG min 283
Driver 2: standstill, SG min n/a
Driver 3: standstill, SG min n/a
Driver 4: standstill, SG min n/a
Driver 5:
Driver 6:
Driver 7:
Driver 8:
Driver 9:
Driver 10:
Driver 11:
Date/time: 2023-08-23 18:25:30
Cache data hit count 4294967295
Slowest loop: 220.83ms; fastest: 0.17ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 9
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 5.9ms, write time 65.4ms, max retries 0
=== Move ===
DMs created 83, segments created 23, maxWait 293517ms, bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves 570, completed 570, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
Heater 0 is on, I-accum = 0.8
Heater 1 is on, I-accum = 0.2
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== Filament sensors ===
Extruder 0: no data received
=== Network ===
Slowest loop: 148.34ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
HTTP sessions: 2 of 8
= WiFi =
Interface state: active
Module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.27
WiFi MAC address 2c:3a:e8:0a:fe:02
WiFi Vcc 3.38, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 25352
WiFi IP address 192.168.178.44
WiFi signal strength -55dBm, mode 802.11n, reconnections 0, sleep mode modem
Clock register 00002002
Socket states: 0 0 0 0 0 0 0 0