I just realized that I didn't include M122 command report. This is the result:
M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.3 (2021-06-15 21:44:54) running on Duet Ethernet 1.02 or later + DueX5
Board ID: 0JD0M-9P6M2-NW4SS-6JTDD-3SJ6P-KAWBK
Used output buffers: 1 of 24 (1 max)
=== RTOS ===
Static ram: 23876
Dynamic ram: 69516 of which 0 recycled
Never used RAM 21024, free system stack 182 words
Tasks: NETWORK(ready,5.6%,565) HEAT(delaying,0.0%,386) Move(notifyWait,0.1%,364) DUEX(notifyWait,0.0%,24) MAIN(running,81.7%,613) IDLE(ready,12.6%,29), total 100.0%
Owned mutexes: USB(MAIN)
=== Platform ===
Last reset 00:00:28 ago, cause: power up
Last software reset at 2023-11-22 15:26, reason: User, GCodes spinning, available RAM 13808, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Step timer max interval 0
MCU temperature: min 26.2, current 28.2, max 28.4
Supply voltage: min 24.3, current 24.3, max 24.4, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 0, standstill, SG min/max not available
Driver 1: position 0, standstill, SG min/max not available
Driver 2: position 0, standstill, SG min/max not available
Driver 3: position 0, standstill, SG min/max not available
Driver 4: position 0, standstill, SG min/max not available
Driver 5: position 0, standstill, SG min/max not available
Driver 6: position 0, standstill, SG min/max not available
Driver 7: position 0, standstill, SG min/max not available
Driver 8: position 0, standstill, SG min/max not available
Driver 9: position 0, standstill, SG min/max not available
Driver 10: position 0
Driver 11: position 0
Date/time: 1970-01-01 00:00:00
Cache data hit count 1097325717
Slowest loop: 6.20ms; fastest: 0.17ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 3.1ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is ready with "M122" in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== DueX ===
Read count 1, 2.08 reads/min
=== Network ===
Slowest loop: 0.24ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 0 of 8
Interface state disabled, link down
ok

I mean the control panel on the windows, that shows the connected ethernet ports in the networks section.
Our board doesn't have raspberry pi attached.
I only see one SD card on the board and one USB drive.
I have attache d a screen of what I see after entering the commands you mentioned.

When I connect the printer through ethernet, the web interface doesn't connect, even the ethernet port is not identified on the control panel. When I connect it through USB and I give the command through Yat (M552 command with IP), the ethernet port can be identified and the web interface starts working, but I see an error: "Your duet rejected the HTTP request: page not found. Check the SD card is mounted and has the correct files in its /www folder." I tried to open the SD card on the PC to see the files and folders, but when I connect it to the PC, it asks me to format it before opening it.

Please let me know how to resolve this issue if you know.

Thanks a lot.