Ok..
I went back to 2.05 and everything was fine again.
I updated to 3.0 and now it works.
It is the same config file.
Thank You very much for your help
Andi
Ok..
I went back to 2.05 and everything was fine again.
I updated to 3.0 and now it works.
It is the same config file.
Thank You very much for your help
Andi
4.3.2021, 07:04:53 Warning: motor phase A may be disconnected reported by driver(s) 0 1
Warning: motor phase B may be disconnected reported by driver(s) 0 1
4.3.2021, 07:04:49 Warning: motor phase A may be disconnected reported by driver(s) 0 1
Warning: motor phase B may be disconnected reported by driver(s) 0 1
4.3.2021, 07:04:45 Warning: motor phase A may be disconnected reported by driver(s) 0 1
Warning: motor phase B may be disconnected reported by driver(s) 0 1
4.3.2021, 07:04:41 M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.2.2 running on Duet WiFi 1.02 or later + DueX5
Board ID: 08DJM-9178L-L4MSN-6JKF4-3SJ6Q-1932R
Used output buffers: 1 of 24 (24 max)
=== RTOS ===
Static ram: 23460
Dynamic ram: 74488 of which 60 recycled
Never used RAM 14072, free system stack 119 words
Tasks: NETWORK(ready,180) HEAT(blocked,308) DUEX(blocked,31) MAIN(running,451) IDLE(ready,20)
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:00:31 ago, cause: power up
Last software reset at 2021-03-03 21:49, reason: User, GCodes spinning, available RAM 13996, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
MCU temperature: min 28.2, current 29.1, max 29.2
Supply voltage: min 24.0, current 24.2, max 24.4, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: position 0, open-load-A, open-load-B, SG min/max not available
Driver 1: position 0, ok, SG min/max not available
Driver 2: position 2000, temperature-shutdown! short-to-ground, standstill, SG min/max not available
Driver 3: position 0, standstill, SG min/max not available
Driver 4: position 0, temperature-shutdown! short-to-ground, standstill, SG min/max not available
Driver 5: position 0, standstill, SG min/max not available
Driver 6: position 0, standstill, SG min/max not available
Driver 7: position 0, standstill, SG min/max not available
Driver 8: position 0, standstill, SG min/max not available
Driver 9: position 0, temperature-shutdown! short-to-ground, standstill, SG min/max not available
Driver 10: position 0
Driver 11: position 0
Date/time: 2021-03-04 07:04:41
Cache data hit count 22518687
Slowest loop: 13.92ms; fastest: 0.29ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 9
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 2.4ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 25368ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 2, completed moves 1, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state 3
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = 2 -1 -1 -1
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Movement lock held by HTTP
HTTP is idle in state(s) 1 8, running macro
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 201.99ms; fastest: 0.09ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
Before the update it was running just fine on 2.05
I didn't touch anything of the wiring at all
I just tried to plug in 2 of the z-motos into X and Y but the problem remains the same.
M122.txt
Hi Frederick,
thank you for this hint. I'm currently running RRF 3.2.2 but I upgraded to 3.0 first
Andi
Hi I am new to this community and after many hours of trying to fix my problem on my own I landed here to ask for your expertise:
I upgraded to RRF3 lately and cant get my Motors to work. Maybe its an obvious problem but i cant figure it out.
Here is my config file:
; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Tue Mar 02 2021 20:27:45 GMT+0100 (Mitteleuropäische Normalzeit)
; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Angryprint V2" ; set printer name
M669 K1 ; select CoreXY mode
; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet
; --- z-axis stepper leveling configuration ---
M671 X-50:-50:370:370 Y330:-65:-65:330 S20 ; Z belts at 4 corners
; --- drive map ---
; _______
; | 6 | 7 |
; | ----- |
; | 5 | 8 |
; -------
; front
Drives
M569 P0 S1 ; X goes forwards
M569 P1 S1 ; Y goes forwards
M569 P2 R-1
M569 P3 S1 ; Extruder goes forwards
M569 P4 R-1
M569 P5 S1 ; Z1 goes forwards
M569 P6 S0 ; Z2 goes backwards
M569 P7 S1 ; Z3 goes forwards
M569 P8 S0
M569 P9 R-1
M584 X0 Y1 E3 Z6:5:8:7 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80 Y80 Z400 E716 ; set steps per mm
M566 X900.00 Y900.00 Z20.00 E1000 ; set maximum instantaneous speed changes (mm/min)
M203 X20000.00 Y20000.00 Z1000.00 E3600.00 ; set maximum speeds (mm/min)
M201 X2500.00 Y2500.00 Z500.00 E1800.00 ; set accelerations (mm/s^2)
M906 X1000 Y1000 Z1000 E500 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
; Axis Limits
M208 X5 Y-5 Z0 S1 ; set axis minima
M208 X310 Y308 Z410 S0 ; set axis maxima
; Endstops
M574 X2 S1 P"xstop" ; configure active-high endstop for high end on X via pin xstop
M574 Y2 S1 P"ystop" ; configure active-high endstop for high end on Y via pin ystop
; Z-Probe
M950 S0 C"duex.pwm5" ; create servo pin 0 for BLTouch
M574 Z1 S2 ; configure Z-probe endstop for low end on Z
M558 P9 C"^zprobe.in" H5 F600 T9000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X0 Y21 Z1.95 ; set Z probe trigger value, offset and trigger height
M557 X10:300 Y21:300 S55 ; define mesh grid
; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S130 ; set temperature limit for heater 0 to 130C
M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S320 ; set temperature limit for heater 1 to 320C
M308 S2 P"e1temp" Y"thermistor" T100000 B4138 ; configure sensor 2 as thermistor on pin e1temp
M950 H2 C"e1heat" T2 ; create chamber heater output on e1heat and map it to sensor 2
M307 H2 B1 S1.00 ; enable bang-bang mode for the chamber heater and set PWM limit
M141 H2 ; map chamber to heater 2
M143 H2 S60 ; set temperature limit for heater 2 to 60C
; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1:2 T45 ; set fan 1 value. Thermostatic control is turned on
M950 F2 C"fan2" Q0 ; create fan 2 on pin fan2 and set its frequency
M950 F3 C"duex.fan7" Q500
M950 F4 C"duex.fan8" Q500
M106 P1 S1 H1:2 T45
; --LED--
M950 P5 C"duex.fan4" Q500
M42 P5 S255
M950 P6 C"duex.fan5" Q500
M42 P6 S255
M950 P7 C"duex.fan6" Q500
M42 P7 S255
; Tools
M563 P0 S"Mosquito" D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
; Custom settings
; --- z-axis stepper leveling configuration ---
M671 X-50:-50:370:370 Y330:-65:-65:330 S20 ; Z belts at 4 corners
; --- drive map ---
; _______
; | 6 | 7 |
; | ----- |
; | 5 | 8 |
; -------
; front
; Miscellaneous
M575 P1 S1 B57600 ; enable support for PanelDue
M501 ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
T0 ; select first tool
The Error:
Warning: motor phase A may be disconnected reported by driver(s) 0 1
Warning: motor phase B may be disconnected reported by driver(s) 0 1
Can someone help me?