@dc42 ok I will make it smaller I wasn’t sure if was asking for the nozzle position at 280 , so when in g30’s commands the offset of the probe is now let’s say zero
Latest posts made by mikeboyle24
-
RE: m671 dual lead screw bed.g
-
RE: m671 dual lead screw bed.g
here is my config with the m671 at the end, just not sure if im setting the bed.g coordinates wrong . RepRapFirmware for Duet 2 WiFi/Ethernet version 2.03```
code_text; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v2.0.0 on Thu Aug 29 2019 22:47:39 GMT-0700 (Pacific Daylight Time) ; General preferences G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"CR10MINI" ; set printer name ; Network M552 S1 ; enable network M586 P0 S1 ; enable HTTP M586 P1 S0 ; disable FTP M586 P2 S0 ; disable Telnet ; Drives M569 P0 S1 ; physical drive 0 goes forwards M569 P1 S0 ; physical drive 1 goes forwards M569 P2 S1 ; physical drive 2 goes forwards M569 P3 S1 ; physical drive 3 goes forwards M569 P4 S0 ; dual z drive M584 X0 Y1 Z2:4 E3 ; set drive mapping M350 X16 Y16 Z16 E16 U16 I1 ; configure microstepping with interpolation M92 X80.00 Y80.00 Z1600.00 E402.00 U1600.00 ; set steps per mm M566 X900.00 Y900.00 Z12.00 E120.00 U12.00 ; set maximum instantaneous speed changes (mm/min) M203 X6000.00 Y6000.00 Z180.00 E1200.00 U180.00 ; set maximum speeds (mm/min) M201 X500.00 Y500.00 Z20.00 E250.00 U20.00 ; set accelerations (mm/s^2) M906 X800 Y800 Z800 E800 U800 I30 ; set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Axis Limits M208 X0 Y0 Z0 S1 ; set axis minima M208 X300 Y230 Z285 S0 ; set axis maxima ; Endstops M574 X1 Y1 S1 ; set active high endstops ; Z-Probe M574 Z1 S2 ; set endstops controlled by probe M558 P5 H5 I1 F120 T6000 ; set Z probe type to switch and the dive height + speeds G31 P500 X-45.4 Y-13 Z0.72 ; set Z probe trigger value, offset and trigger height M557 X15:215 Y15:195 S20 ; define mesh grid ; Heaters M305 P0 T100000 B4138 R4700 ; set thermistor + ADC parameters for heater 0 M143 H0 S120 ; set temperature limit for heater 0 to 120C M305 P1 T100000 B4138 R4700 ; set thermistor + ADC parameters for heater 1 M143 H1 S280 ; set temperature limit for heater 1 to 280C ; Fans M106 P0 S0 I0 F500 H-1 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off M106 P1 S1 I0 F500 H1 T45 ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on ; Tools M563 P0 D0 H1 F0 ; define tool 0 G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C ; bed leveling lead screw coordinates M671 X-30.0:334.0 Y115:115 S0.5 ; lead screw positions ; Custom settings are not defined ; Miscellaneous M501 ; load saved parameters from non-volatile memory
-
m671 dual lead screw bed.g
i just finish upgrading my cr10mini with a duet wifi
and ran a g32 it did everything fine intell it got to the end of my bed.g file where i entered in the x y coordinates for example and it ends up hitting X max? if i type it in manual it stops exactly were i want it ```
code_text; called to perform automatic bed compensation via G32 ; ; generated by RepRapFirmware Configuration Tool v2.0.0 on Thu Aug 29 2019 22:47:39 GMT-0700 (Pacific Daylight Time) M561 ; clear any bed transform G29 ; probe the bed and enable compensation G30 P0 X60 Y115 Z-99999 ; left lead screw G30 P1 X280 Y115 Z-99999 S2 ; right lead screw