Duet wifi v1.04, upgraded reprap firmware 2.03
-
Duet wifi v1.04,
Good day. I upgraded the duet2 wifi to reprap firmware 2.03 (2019-06-13b2). When I turn on the printout from ABS, the fans turn on 78%. How to turn it off?
The fans are turned off in the blowmistress. in config I have:
M106 P1 H-1 S0;
M106 P2 H-1 S0
The firmware was fine before the change -
Can you post your config.g?
-
; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2 on Sun Feb 24 2019 22:58:40 GMT+0100 (czas środkowoeuropejski standardowy); General preferences
M111 S0;
G21
G90 ; Send absolute coordinates...
M82 ; ...but relative extruder moves; Network
M550 P"GIANTS" ; Set machine name
M552 S1 ; Enable network
M587 S" ; Configure access point and IP addresses. You can delete this line once connected
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet; Drives
M569 P0 S1 ; Drive 0 os X
M569 P1 S0 ; Drive 1 os Y
M569 P2 S1 ; Drive 2 os Z
M569 P3 S1 ; Drive 3 os U
M569 P4 S1 ; Drive 4 os Y
M569 P5 S0 ; Drive 5 ekstruder lewy
M569 P6 S0 ; Drive 6 ekstruder prawy
M584 X0 Y1:4 Z2 U3 E5:6 ; U Dodatkowy silnik w osiX
M350 X32 Y32:32 U32 Z256 E64:64 I0 ; Configure microstepping
M92 X160.85 Y160.75:160.75 U160.85 Z25800 E370:370 ; Set steps per mm
M566 X300.00 Y300.00:300.00 U300.00 Z12.00 E120.00:120.00 ; Set maximum instantaneous speed changes (mm/min)
M572 D0 S0.015
M572 D1 S0.015
M203 X10000.00 Y10000.00:10000.00 U10000.00 Z200.00 E1200.00:1200.00 ; Set maximum speeds (mm/min)
M201 X3000.00 Y3000.00:3000.00 U3000.00 Z100.00 E250.00:250.00 ; Set accelerations (mm/s^2)
M906 X1400.00 Y1200.00:1200.00 U1400.00 Z1700.00 E1700.00:1700.00 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S0 ; Set idle timeout
M564 S1 H0 ; Set idle timeout
M208 X316 Y285 U317 Z250 ; Set axis maxima
M208 X-60 Y0 U0 Z0 S1 ; Set axis minima
M558 P0M574 X1 Y1 U2 Z1 S1 ;krancowka U na maksimum
; Heaters
M307 H0 B0 S1.00 ; Disable bang-bang mode for the bed heater and set PWM limit
M305 P0 T100000 B4635 C9.503333e-8 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S120 ; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4635 C9.503333e-8 R4700 ; Set thermistor + ADC parameters for heater 1
M143 H1 S253 ; Set temperature limit for heater 1 to 253C
M305 P2 T100000 B4635 C9.503333e-8 R4700 ; Set thermistor + ADC parameters for heater 2
M143 H2 S253 ; Set temperature limit for heater 2 to 253CM106 P0 S200 ; Wentylator chloszenia elektroniki, lewy przod
M106 P1 H-1 S0 ; Wentylator chlodzenie wydruku lewy
M106 P2 H-1 S0 ; Wentylator chlodzenia wydruku prawy
M106 P3 S1 I0 F500 H1 T45 ; Ustaw wartosc wentylatora 1, odwrocenie i czestotliwosc sygnału PWM. Sterowanie termostatyczne jest wlaczone
M106 P4 S1 I0 F500 H2 T45 ; Ustaw wartosc wentylatora 2, odwrocenie i czestotliwosc sygnału PWM. Sterowanie termostatyczne jest wlaczone
M106 P5 S200 ; Wentylator chlodzenia elektroniki, lewy tyl
M106 P6 S200 ; Wentylator chlodzenia elektroniki, prawy tyl
M106 P7 S200 ; Wentylator chlodzenia elektroniki, prawy przod
M106 P8 S80 ; Uruchom wentylator HEPA z limited predkosciaM563 P0 D0 H1 F1 ; narzedzie 0 uzywa wytlaczarki 0, grzejnika 1 i wentylatora 1
G10 P0 X0 Y0 Z0 S0 R0 ; ustaw korekcje narzedzia i temperaturyM563 P1 D1 H2 X3 F2 ; narzedzie 1 wykorzystuje wytlaczarke 1, podgrzewacz 2, wentylator 2 i odwzorowuje X na U
G10 P1 Y0.7 U0 Z0 S0 R0 ; ustaw przesuniecia 1 narzedzia i temperaturyM563 P2 D0: 1 H1: 2 X0: 3 F1: 2 ; narzedzie 2 wykorzystuje zarowno wytlaczarki, podgrzewacze ciepla i wentylatory, jak i odwzorowuje X na X i U
G10 P2 X40 Y0 U-40 Z0 S0 R0 ; ustawic korekcje narzedzi i temperaturyM567 P2 E1: 1 ; ustawic stosunek mieszania 100% na obu wytlaczarkach
; Automatic saving after power loss is not enabled
; Custom settings are not configured
; Automatic saving after power loss is not enabled
; Miscellaneous
M501
T0 ; Select first tool ; Select first tool -
If it's turning on during a print is the slicer turning it on?
Can you post the gcode you're trying to print? Or look through it for m106 commands.
-
; KISSlicer - PRO
; Windows
; version 2 a 0.4.4 Win64
; Built: Jul 7 2018, 11:14:03
; Running on 4 cores
;
; Saved: 2019-07-18 20:21:29
; 'PI3_mitsubishiL mitsubishiPP.gcode'
;
; Anti-shrink gain x=1.000000, y=1.000000, z=1.000000
;
; *** Printer Settings ***
;
; printer_name = Tryb kopii - ABS
; profile_date = 2019-07-18 20:20:59
; bed_STL_filename =
; extension = gcode
; cost_per_hour = 0
; g_code_prefix = 473231200A473930200A4D3832200A4732380A473120
; ^ 5A350A54320A54203C455854202B20313E0A4D3134302053203C4245
; ^ 443E200A4D313136200A4D3130342053203C54454D503E200A4D3130
; ^ 392053203C54454D503E200A4D3130342053203C54454D503E0A5432
; ^ 20
; > Decoded
; > G21
; > G90
; > M82
; > G28
; > G1 Z5
; > T2
; > T <EXT + 1>
; > M140 S <BED>
; > M116
; > M104 S <TEMP>
; > M109 S <TEMP>
; > M104 S <TEMP>
; > T2
; g_code_preheat = 3B20686561742074686520286E6578742C207468656
; ^ E2063757272656E742920657874727564657220776974686F7574207
; ^ 7616974696E670A3B4D31303420533C54454D503E20543C4558542B3
; ^ 03E0A3B20556E636F6D6D656E74207468652070726576696F7573206
; ^ C696E6520746F20656E61626C6520707265686561740A
; > Decoded
; > ; heat the (next, then current) extruder without waiting
; > ;M104 S<TEMP> T<EXT+0>
; > ; Uncomment the previous line to enable preheat
; g_code_warm = 3B204865616420746F20746865207374617274206F6620
; ^ 746865206E65787420706174680A3B473120583C4E455854583E2059
; ^ 3C4E455854593E2046363030300A3B47342050300A3B2053656C6563
; ^ 742074686520546F6F6C20286578747275646572290A3B543C455854
; ^ 2B303E0A3B20436F727265637420706F736974696F6E20666F72206D
; ^ 756C74692D6E6F7A7A6C650A3B473120583C4E455854583E20593C4E
; ^ 455854593E2046363030300A3B47342050300A3B205365742074656D
; ^ 7020616E64207468656E20776169740A3B4D31303420533C54454D50
; ^ 3E0A3B4D31303920533C54454D503E0A3B205055524745204F522050
; ^ 52494D45204845524520494620444553495245440A
; > Decoded -
Why does this record not turn off the fans?
M106 P1 H-1 S0
M106 P2 H-1 S0After all, it shows that the thermostat is turned off
-
That gcode section doesn't show enough to see if it's sending any M106 commands. I suggest you open the gcode file in a text editor and searching for M106
-
Problem solved.
I added M107 to the kisslicer
Thank you for your help