Upgrade from 1.22.6 to 1.24 Has Goosed *.local addressing.
-
Hi All,
Having issues with a duet v0.6 that has stopped talking to the network.
I've tried different leads and disconnected a dc42 IR probe that i had just swapped in on a different fault diagnostic. Here is the M122 response. Any ideas? I will try bossac loading the firmware again, and double check release note to ensure I hadn't missed anything between 1.22.6 and 1.24.
=== Diagnostics ===
RepRapFirmware for Duet version 1.24 running on Duet 0.6
Used output buffers: 2 of 16 (2 max)
=== System ===
Static ram: 44204
Dynamic ram: 42580 of which 3328 recycled
Stack ram used: 1080 current, 2452 maximum
Never used ram: 5740
=== Platform ===
Last reset 00:07:15 ago, cause: power up
Last software reset at 2019-07-27 07:22, reason: User, spinning module GCodes, available RAM 4300 bytes (slot 3)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0400f000 BFAR 0xe000ed38 SP 0xffffffff
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 21.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 37.9, current 58.2, max 58.6
Date/time: 1970-01-01 00:00:00
Slowest loop: 0.32ms; fastest: 0.10ms
I2C nak errors 24, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 24
=== Move ===
Hiccups: 0, FreeDm: 100, MinFreeDm: 100, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== DDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 2 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is ready with "M122" in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Free connections: 16 of 16
Free transactions: 24 of 24
Locked: 0, state: 4, listening: 20071bf4, 0, 0
ok -
Just seen this on startup. Bug?
Done!
RepRapFirmware for Duet is up and running.
Network up, IP=192.168.85.113
Bad command: Done!
ok
Bad command: RepRapFirmware for Duet is up and running.
ok
Bad command: etwork up, IP=192.168.85.113
ok -
Odd, my .local address doesn't work but the IP address does...
wesbrooks@shlapentop:~$ ping ormergog.local
ping: ormergog.local: Name or service not known
wesbrooks@shlapentop:~$ ping 192.168.85.113
PING 192.168.85.113 (192.168.85.113) 56(84) bytes of data.
64 bytes from 192.168.85.113: icmp_seq=1 ttl=255 time=0.159 ms
64 bytes from 192.168.85.113: icmp_seq=2 ttl=255 time=0.240 ms
64 bytes from 192.168.85.113: icmp_seq=3 ttl=255 time=0.197 ms
64 bytes from 192.168.85.113: icmp_seq=4 ttl=255 time=0.276 ms
64 bytes from 192.168.85.113: icmp_seq=5 ttl=255 time=0.230 ms
64 bytes from 192.168.85.113: icmp_seq=6 ttl=255 time=0.198 ms
64 bytes from 192.168.85.113: icmp_seq=7 ttl=255 time=0.226 ms
64 bytes from 192.168.85.113: icmp_seq=8 ttl=255 time=0.211 ms
64 bytes from 192.168.85.113: icmp_seq=9 ttl=255 time=0.228 ms
^C
--- 192.168.85.113 ping statistics ---
9 packets transmitted, 9 received, 0% packet loss, time 8200ms
rtt min/avg/max/mdev = 0.159/0.218/0.276/0.033 ms
wesbrooks@shlapentop:~$ ^C
wesbrooks@shlapentop:~$ -
Network section of config.g:
; Network
M550 P"OrmerGog" ; Machine name (can be anything you like)
M540 P0xBE:0xEF:0xDE:0xAD:0xFE:0xF0 ; MAC Address
M552 P0 ; IP address (0 = use DHCP)
M555 P2 ; Set output to look like Marlin
M575 P1 B57600 S1 ; Comms parameters for PanelDue
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet -
Tried the following with no luck. Access via IP address still works fine, ormergog.local doesn't. Now rolling back to 1.22.6.
; Network
M550 POrmerGog ; Machine name (can be anything you like)
M540 PBE:EF:DE:AD:FE:F0 ; MAC Address
M552 P0 S1 ; IP address (P0 = use DHCP, S1 = Enable Networking)
M554 P192.168.85.1 ; Gateway
M553 P255.255.255.0 ; Subnet mask
M555 P2 ; Set output to look like Marlin
M575 P1 B57600 S1 ; Comms parameters for PanelDue
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet -
Currently running Duet Web Control 2.0.0-RC6.
-
.local addressing works fine on 1.23 (2018-12-24b1) .
-
The MDNS support in the LWIP TCP/IP library was crashing RRF on some user's machines. On investigation I found the that MDNS code was pile of junk, with error checking missing in multiple places, causing buffer overflows and/or null pointer dereferences - hence the problems. So MDNS support was removed in version 1.23. See https://forum.duet3d.com/topic/8352/duet-0-6-randomly-reboots/5.
Anyone interested in fixing RRF to reinstate this functionality should consider upgrading the version of LWIP used by RRF to version 2.
-
Argh! Ok, fair enough. I'll have to sort out the mac address IP reserves on the router again.
That is really easy to miss in the release notes if you had no idea what MDNS is.
-
I've updated the upgrade notes to mention ".local" addressing.
