Problem with bed level with NO mesh compensation
-
Wait.. I'm trying to print, but the bed don't raise up.
When I try to lunch the print, the heater are correctly heating, the home is ok, but when the print start the head move in XY correctly but the bed remain in the bottom of printer.
Attach the part of config.g and homeall.g:
Config.g
; Axis Limits
M208 X0 Y0 Z0 U0 S1 ; set axis minima
M208 X390 Y420 Z390 U390 S0 ; set axis maxima; Endstops
M574 X1 Y1 S1 ; set active high endstops
M574 Z1 U1 S1 ; set active low endstops; Z-Probe
M574 Z1 U1 S1 ; set endstops controlled by probe
M558 P0 H370 F120 T6000 ; disable Z probe but set dive height, probe speed and travel speed
M557 X15:375 Y15:405 S15 ; define mesh gridHomeall.g
; homeall.g
; called to home all axesG91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 X-395 Y-425 F1800 ; move quickly to X or Y endstop and stop there (first pass)
G1 H1 X-395 ; home X axis
G1 H1 Y-425 ; home Y axis
G1 X5 Y5 F6000 ; go back a few mm
G1 H1 X-395 F360 ; move slowly to X axis endstop once more (second pass)
G1 H1 Y-425 ; then move slowly to Y axis endstop
G1 H1 Z-395 U-395 F360 ; move Z up stopping at the endstop
G90 ; absolute positioning
G92 Z0 U0 ; set Z to axis minimum (you may want to adjust this)(the U parameters are because I've two indipendent motors for Z)
I've try some options; the last one is change "G92 Z0 U0 " in "G92 Z-390 U-390" without resoults
Please help me
-
in the normal config both z motors need to be configured on z.
only during homing you spliy z up into 2 axis to home them independently and at the end you combine them again.
-
Yes but the split of motor Z work very well.. My problem is that when the print start, the bed don't raise up in the top of printer but remain in the bottom..
Why you speack about z motor split?
-
@alil2096 said in Problem with bed level with NO mesh compensation:
G1 H1 Z-395 U-395 F360 ; move Z up stopping at the endstop
this indicates that you configued your endstop to be at min.
that means z=0 is when the bed is at the bottom.
-
So, I must put "0" where there is "-395"?
-
i would suggest that you recreate the config in the configurator. there are more settings that need to be changed.
-
Ok.. if there are updates for firmware I can update, for a very clear installation
-
the configurator is here
https://configtool.reprapfirmware.org/Startand the information about the firmware update is here
https://duet3d.dozuki.com/Wiki/Installing_and_Updating_Firmwarefind the up to date releases here (for now you should go for 2.04 firmware)
https://github.com/dc42/RepRapFirmware/releases -
I can't rebuild the firmaware because there are too personals settings in others voices..
I just want fix this problem with endstop.. Do you have another ideas?
-
the location of th endstop is configured using
M574
https://duet3d.dozuki.com/Wiki/Gcode#Section_M574_Set_endstop_configurationthen you need to adjust all the movement parts in the homing script to account for a changed direction.
-
And this is clear.
I have X and Y endstop in 0;0, and I've copy the same impostaztion for Z axis, so now when I puch the "Home All" bottom, all axes go to home correctly. So, after home process, I have all axes in 0;0;0 and I can read this in the box in the top-left of duet web control.
My first test was that change the value of Z min from 0 to 390. So after homing I can read 0;0;390 in the box, but when the print start, Z axis go in Z-, and strains on the switch, because for my configuration Z+ in from top to bottom
Can I change this setting? So, if I try to put Z+ from bottom to top I can resolve the problem?
-
@alil2096 said in Problem with bed level with NO mesh compensation:
in the box, but when the print start, Z axis go in Z-,
if you axis goes in the wrong direction you need to change the corresponding M569 command.
also refer to this guide
https://duet3d.dozuki.com/Wiki/Choosing_and_connecting_stepper_motors -
So, after home process, I have all axes in 0;0;0 …
… where Z=0 is at the bottom of your printer, right? Well, in order to print, the bed must be near the nozzle, that is, the first layer is always printed at (or near) Z=0. For each additional layer, Z will be incremented, which translates into the bed moving down.
Of course you can have the Z end stop at the bottom of the printer, but this determines the maximum Z value (390 in your case?), whereas Z=0 must be at the top.
