• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login

Cannot connect to new Duet V0.8.5

Scheduled Pinned Locked Moved
Firmware installation
2
13
1.9k
Loading More Posts
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • undefined
    dc42 administrators
    last edited by 10 Feb 2017, 18:01

    Assuming it's a Duet 085, see https://duet3d.com/wiki/What_to_do_if_your_Duet_or_Duet_WiFi_won%27t_respond.

    Duet WiFi hardware designer and firmware engineer
    Please do not ask me for Duet support via PM or email, use the forum
    http://www.escher3d.com, https://miscsolutions.wordpress.com

    1 Reply Last reply Reply Quote 0
    • undefined
      Robny
      last edited by 10 Feb 2017, 19:01

      Thanks for the quick reply

      When I check device manager it sees it as a USB serial device (COM4).

      The only thing I have done is flashed the firmware, so I dont know if there is anything else I need to do after that, I have been following lots of guides but seem t be going around in circles.

      1 Reply Last reply Reply Quote 0
      • undefined
        dc42 administrators
        last edited by 10 Feb 2017, 19:14

        Does the COM4 port appear when you connect to the USB cable tongue Duet, and disappear when you disconnect it? If so, you should be able to connect to COM4 with Pronterface.

        Which firmware version did you download, and how large was the binary? It it's a recent version, it should be nearly 200kbytes.

        Duet WiFi hardware designer and firmware engineer
        Please do not ask me for Duet support via PM or email, use the forum
        http://www.escher3d.com, https://miscsolutions.wordpress.com

        1 Reply Last reply Reply Quote 0
        • undefined
          Robny
          last edited by 10 Feb 2017, 19:19

          I downloaded the 1.17d, I do not have Pronteface on my computer do I need it? It was about 290k in size.

          Is there a step by step guide that I can follow?

          Thanks for replying
          Rob

          1 Reply Last reply Reply Quote 0
          • undefined
            Robny
            last edited by 10 Feb 2017, 19:21

            Do I need to also download the Duet Web Control and flash that?

            This is what I'm looking at:

            https://github.com/dc42/RepRapFirmware/tree/dev/Release/Duet-0.6-0.8.5/Stable

            1 Reply Last reply Reply Quote 0
            • undefined
              dc42 administrators
              last edited by 10 Feb 2017, 19:30

              On the Duet 085 the DuetWebControl files live on the SD card. See https://duet3d.com/wiki/SD_card_folder_structure.

              Unless you have a terminal emulator installed on your computer, I suggest you download and install Pronterface.

              Duet WiFi hardware designer and firmware engineer
              Please do not ask me for Duet support via PM or email, use the forum
              http://www.escher3d.com, https://miscsolutions.wordpress.com

              1 Reply Last reply Reply Quote 0
              • undefined
                Robny
                last edited by 10 Feb 2017, 20:17

                Sorry..what do I need Pronteface for? I have simplify 3d, will that do th same?

                1 Reply Last reply Reply Quote 0
                • undefined
                  dc42 administrators
                  last edited by 10 Feb 2017, 20:47

                  You can use s3d but make sure you set it to hardware flow control in its communication parameters.

                  Duet WiFi hardware designer and firmware engineer
                  Please do not ask me for Duet support via PM or email, use the forum
                  http://www.escher3d.com, https://miscsolutions.wordpress.com

                  1 Reply Last reply Reply Quote 0
                  • undefined
                    Robny
                    last edited by 10 Feb 2017, 20:48

                    Okay I'm really struggling with this, no matter what I do I cannot get connected to the web interface. As far as I can tell the firmware was flashed properly with the most recent update 1.17e. I've tried pinging the board and I do not get a response from it, I'm getting confused with varying guides from all over the internet.

                    I'm doing an upgrade from RAMPS so I'm not that new to this…I constantly get timed out messages, would be great if there was a guide to walk through step by step, I'm just picking up bits of info from everywhere..at the moment I'm just getting frustrated and the excitement is slowly dwindling...please help

                    Thnak you

                    1 Reply Last reply Reply Quote 0
                    • undefined
                      dc42 administrators
                      last edited by 10 Feb 2017, 20:53

                      You need to get Pronterface or s3d or Arduino Serial Monitor communicating with the Duet. See my previous reply about using s3d. Once you have established communication, you can send M552 to check the network status.

                      Duet WiFi hardware designer and firmware engineer
                      Please do not ask me for Duet support via PM or email, use the forum
                      http://www.escher3d.com, https://miscsolutions.wordpress.com

                      1 Reply Last reply Reply Quote 0
                      • undefined
                        Robny
                        last edited by 10 Feb 2017, 21:12

                        Hi

                        I did that and gor the following response:
                        Connecting…
                        Printer is now online.

                        M552
                        SENDING:M552
                        Network is enabled, configured IP address: 192.168.1.14, actual IP address: 192.168.1.14, HTTP port: 80

                        I entered that IP address into my browser and received this message:

                        This site can’t be reached

                        192.168.1.14 took too long to respond.
                        Try:
                        Checking the connection
                        Checking the proxy and the firewall
                        Running Windows Network Diagnostics
                        ERR_CONNECTION_TIMED_OUT

                        I seem to have communication with the board in Pronterface and in Arduino but I keep getting stuck at the above stage. I cannot connect to the interface but the board seems to be configured okay.

                        I appreciate your help.

                        1 Reply Last reply Reply Quote 0
                        • undefined
                          Robny
                          last edited by 10 Feb 2017, 21:40

                          Its Sorted 🙂

                          I really do appreciate your help and being in constant contact….thank you.

                          As it happens it turned out to be a bad Ethernet cable, I was using the wrong type of Ethernet cable, soon as I changed it, it loaded straight into the interface.

                          Thanks again, excited again 🙂
                          Rob

                          1 Reply Last reply Reply Quote 0
                          11 out of 13
                          • First post
                            11/13
                            Last post
                          Unless otherwise noted, all forum content is licensed under CC-BY-SA