"No known networks found" error

A Former User

It could be a faulty wifi module, or it could be a signal quality issue, or it could be an encryption issue.

Easiest way to check if the radio is okay is to put the Duet into access point mode imo.
https://duet3d.dozuki.com/Wiki/Gcode#Section_M589_Configure_access_point_parameters

JaredP

M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.05.1 running on Duet WiFi 1.02 or later
Board ID: 08DGM-917NK-F2MS4-7J1F8-3SD6R-KHT4F
Used output buffers: 1 of 24 (1 max)
=== RTOS ===
Static ram: 25712
Dynamic ram: 92740 of which 0 recycled
Exception stack ram used: 256
Never used ram: 12364
Tasks: NETWORK(ready,1876) HEAT(blocked,1232) MAIN(running,4752) IDLE(ready,160)
Owned mutexes:
=== Platform ===
Last reset 00:00:32 ago, cause: power up
Last software reset time unknown, reason: Heat task stuck, spinning module FilamentSensors, available RAM 11916 bytes (slot 3)
Software reset code 0x00ad HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0043380f BFAR 0xe000ed38 SP 0x20004aac Task 0x4e49414d
Stack: 0044d941 0044d940 61000000 00000000 3fdb4e81 3edb6db7 b7b4d800 3331bb4c 40000000 3f317200 b5ddea0e 388aa908 bb35fe81 3c4192f5 3f800000 00000000 3f800000 a0000000 00000000 60000010 0044d941 00000000 ffffffff
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 18.1, current 21.6, max 21.7
Supply voltage: min 0.0, current 0.4, max 0.5, under voltage events: 0, over voltage events: 0, power good: no
Driver 0: ok, SG min/max not available
Driver 1: ok, SG min/max not available
Driver 2: ok, SG min/max not available
Driver 3: ok, SG min/max not available
Driver 4: ok, SG min/max not available
Date/time: 1970-01-01 00:00:00
Cache data hit count 48878098
Slowest loop: 0.15ms; fastest: 0.05ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 160, MinFreeDm: 160, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== DDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is ready with "M122" in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 0.15ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 0 of 8

WiFi -
Network state is disabled
WiFi module is disabled
Failed messages: pending 2779096485, notready 2779096485, noresp 2779096485
Socket states: 0 0 0 0 0 0 0 0
ok

M589 S"test" P"test1234" I192.168.0.1
ok
M552 S2
ok
WiFi module is providing access point test, IP address 192.168.0.1
Error retrieving WiFi status message: bad reply format version
WiFi module is providing access point test, IP address 192.168.0.1

Blue light is on. The SSID "test" is being broadcast.

A Former User

@JaredP said in "No known networks found" error:

Blue light is on. The SSID "test" is being broadcast.

you can connect to it and it provides dhcp and connectivity in general?

JaredP

It gave me an IP address, 192.168.0.2.

And yes, I can connect to it and access the printer control panel.

A Former User

I'm guess the radio is okay then, hopefully its doable to sort out what is wrong with the firmware.

dc42

Three possible reasons for "No known networks found":

You have hidden the SSID in your router configuration. If you do that then you must specify the SSID you want to connect to in the M552 S1 command.
You have mistyped the SSID in the M587 command. Run M587 to list known networks and check that the one in the remembered list matches exactly the one that the router is transmitting on 2.4GHz.
The chosen network signal is too weak where the printer is. Move the printer into the same room as the router and try again. If that works, see https://duet3d.dozuki.com/Wiki/WiFi_disconnections_and_AJAX_timeout_errors.

A Former User

I read the thread as it having another Duet working under the same conditions; was I mistaken?

JaredP

I did have a clone board working from the same location previously. It went into another machine, and I bought a genuine Duet to replace it. My SSID is not hidden. I've tried quite a few times to connect, however I'll try moving closer temporarily.

Here is M587:

M587
Remembered networks:
TNCAPF2FD81 IP=192.168.1.14 GW=0.0.0.0 NM=0.0.0.0
Matt Damon IP=0.0.0.0 GW=0.0.0.0 NM=0.0.0.0
ok

A Former User

Thats what I thought; could you just make sure there isn't a difference in the rrf or wifi firmware between the two boards before/after making the swap?

JaredP

Here is my M115

M115
FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 2.05.1 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2020-02-09b1
ok

How can I check the wifi version? I have ran M997 S1 on version 1.23, I saw the whole install progression without any issues.

A Former User

@JaredP said in "No known networks found" error:

How can I check the wifi version? I

its part of the M122output, way down at the bottom.

JaredP

Okay, I suppose it errored out in the M112 i ran earlier.
Now that i'm in AP mode, I can see my wifi version is 1.23

=== Network ===
Slowest loop: 8446.02ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 0 of 8

WiFi -
Network state is running
WiFi module is providing access point
Failed messages: pending 0, notready 0, noresp 1
WiFi firmware version 1.23
WiFi MAC address 86:0d:8e:b3:b4:93
WiFi Vcc 3.34, reset reason Hardware watchdog
WiFi flash size 4194304, free heap 25616
WiFi IP address 192.168.0.1
Connected clients 0
Socket states: 0 0 0 0 0 0 0 0

So now that I know I'm on 1.23 & 2.05.1, what else can I do? I did a speed test from my phone where my printer is located and I am getting 108 mbps/18 ms, i'm positive it's not connection strength.

JaredP

Just figured it out. Nothing wrong with the board.

I had to reset my routing and AP configurations on my Ubiquiti network hardware due to a corruption or something, just recently. I didn't realize I had specified this time to separate my 2.4 and 5Ghz SSIDs. Now my 2.4Ghz SSID became named Matt Damon_IoT by default, while I was asking the board to try to connect to the 5Ghz exclusive SSID.

Specifying "Matt Damon_IoT" allowed me to connect with M552 S1.

I apologize to you guys for framing this as a duet issue, but at least this can perhaps be a new part of the questionnaire if guys pop up with this problem again, haha.

A Former User

@JaredP said in "No known networks found" error:

but at least this can perhaps be a new part of the questionnaire

it would have been it you'd said you changed any thing other than the Duet; anyways this probably why the Duet replacement is "difficult" - rarely anything wrong with the board;) All that ends well and all that jazz:)