YAT wouldn't respond

monster

Huh!
Information...

Guys, I do want to use Pi. I was more like complaining that big picture of result (what does what) and way to get there isn't very clear

Now while I'm flashing another card with "DuetPi (with GUI)"
I've inserted SD that came with Duet into Pi and I able to see that it did get IP on my router Progress

though that going with browser to that IP address doesn't get me anywhere. Is there a resource "What to do when Web UI is working?"

monster

I forgot to mention
My Pi has no monitor for it - I kinda hopping to get things done remotely...

A Former User

@monster said in YAT wouldn't respond:

I do want to use Pi

I kinda hopping to get things done remotely...

No problem. ~~put a file called ssh on the FAT32 partition of the Raspberry Pi image. Just ssh, no extension. That enables the ssh server so~~ you can log in with your favourite ssh client (putty if on windows).

When the image of your choice has been flashed, the Duet 3 can be connected to via the hostname "duet3". It comes preconfigured with mDNS enabled (via avahi), SSH activated and the standard credentials "pi" and "raspberry". To set up WiFi, you can edit "wpa_supplicant.conf" on the SD card (first partition).

if you need wireless network set up, you put another file on the card. wpa_supplicant.conf with your country code and wifi details in it, example below

ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=netdev
update_config=1
country=UK

network={
    ssid="your network name"
    psk="your network key"
}

monster

@monster said in YAT wouldn't respond:

card with "DuetPi (with GUI)"

Current status is this:
A - Original Duet card
When this card is in Pi - I got Web UI working (uploaded config.g generated by https://configtool.reprapfirmware.org ), can't yet move any motor.

B - Another SD card flashed with "DuetPi (with GUI)" and on top of that put file "ssh" in root, "wpa_supplicant.conf" in root.
When this card is in Pi - no IP address obtained from router...

I guess question of this topic is mostly solved - some way to connect is working
Thank you for your help!!!

P.S. Do I upload all files that configtool.reprapfirmware.org made to Web UI??? All to root? Or "sys" dir to root? Or?

Danal

@monster said in YAT wouldn't respond:

hat put file "ssh" in root

The card etched from the image should have a 'boot' partition (B Boot, not R Root). The two files go in that partition, no subdirectories.

@monster said in YAT wouldn't respond:

P.S. Do I upload all files that configtool.reprapfirmware.org made to Web UI??? All to root? Or "sys" dir to root? Or?

DO NOT UNZIP
Just upload the zip file itself via the "system" tab, "upload system files" button.

A Former User

@monster said in YAT wouldn't respond:

A - Original Duet card
B - Another SD card flashed with "DuetPi (with GUI)"

the simple solution is use card A; although they should be the same; and not need the ssh file (unless you use a vanilla raspbian image). and if card A worked without wpa_supplicant.conf I'm guessing you're not using wifi?

That the motors don't move is probaly down to configuration, as they won't move until homed.

(you can override with
https://duet3d.dozuki.com/Wiki/Gcode#Section_M564_Limit_axes
https://duet3d.dozuki.com/Wiki/Gcode#Section_G92_Set_Position
https://duet3d.dozuki.com/Wiki/Gcode#Section_G0_G1_Move (G0 H2) )

monster

@bearer said in YAT wouldn't respond:

@monster said in YAT wouldn't respond:

A - Original Duet card
B - Another SD card flashed with "DuetPi (with GUI)"

the simple solution is use card A; although they should be the same; and not need the ssh file (unless you use a vanilla raspbian image). and if card A worked without wpa_supplicant.conf I'm guessing you're not using wifi?

I would like to use WiFi! As this extra eithernet wire is... is an extra wire

That the motors don't move is probaly down to configuration, as they won't move until homed.

(you can override with
https://duet3d.dozuki.com/Wiki/Gcode#Section_M564_Limit_axes
https://duet3d.dozuki.com/Wiki/Gcode#Section_G92_Set_Position
https://duet3d.dozuki.com/Wiki/Gcode#Section_G0_G1_Move (G0 H2) )

Yes, when I attempt to use UI to move the motors it says that nothing is homed. And I guess in order to home axis's I'd need to marry end stops with their motors/axis's, right? Last night I was trying to find how - failed

Thank you for links - I'll study them today!

A Former User

@monster said in YAT wouldn't respond:

I would like to use WiFi!

if you can log in using ethernet just run sudo raspi-config as it may be simpler than to edit /etc/wpa_supplicant/wpa_supplicant.conf otherwise you'll just need to put the file on the correct partition, there should be a config.txt file on the correct partition (along with a bunch other files bcm27* and so on)

A Former User

@monster said in YAT wouldn't respond:

And I guess in order to home axis's I'd need to marry end stops with their motors/axis's, right?

correct
https://duet3d.dozuki.com/Wiki/Connecting_endstop_switches

monster

@bearer said in YAT wouldn't respond:

sudo raspi-config

A recall from yesterday.
Yesterday I've tried that - I get from config tool:

"Could not communicate with wpa_supplicant"

Tried again now - same result.

Then I used way of pain (AKA vim) to edit

/etc/wpa_supplicant/wpa_supplicant.conf

then rebooted, still no WIFI connection.
Obviously this is about partitions that you referred about. I must admit I'm not fully understand neither linux architecture not filesystem of it.

monster

@Danal said in YAT wouldn't respond:

@monster said in YAT wouldn't respond:

hat put file "ssh" in root

The card etched from the image should have a 'boot' partition (B Boot, not R Root). The two files go in that partition, no subdirectories.

@monster said in YAT wouldn't respond:

P.S. Do I upload all files that configtool.reprapfirmware.org made to Web UI??? All to root? Or "sys" dir to root? Or?

DO NOT UNZIP
Just upload the zip file itself via the "system" tab, "upload system files" button.

Done that! Thank you!

A Former User

@monster said in YAT wouldn't respond:

"Could not communicate with wpa_supplicant"

could be a lacking country code is preventing it bringing up the wifi interface (the country code is there for regulatory approval, no code, no wifi to, avoid using channels outside local regulatory approvals)

A Former User

@monster said in YAT wouldn't respond:

Then I used way of pain (AKA vim) to edit
/etc/wpa_supplicant/wpa_supplicant.conf

nano is a bit more user friendly if vi is troublesome

suspect the content is either wrong or incomplete.

i'd try the below, then sudo raspi-config after rebooting.

cat << EOF | sudo tee -a /etc/wpa_supplicant/wpa_supplicant.conf
ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=netdev
update_config=1
country=UK
EOF

monster

@bearer said in YAT wouldn't respond:

@monster said in YAT wouldn't respond:

"Could not communicate with wpa_supplicant"

could be a lacking country code is preventing it bringing up the wifi interface (the country code is there for regulatory approval, no code, no wifi to, avoid using channels outside local regulatory approvals)

Ahaa
True, my region settings were unchanged.
But still
If i go to config / P4 (Localization Options) / I4 (Change Wifi country) I still get:

Could not communicate with wpa_supplicant

monster

@bearer said in YAT wouldn't respond:

@monster said in YAT wouldn't respond:

Then I used way of pain (AKA vim) to edit
/etc/wpa_supplicant/wpa_supplicant.conf

nano is a bit more user friendly if vi is troublesome

suspect the content is either wrong or incomplete.

i'd try the below, then sudo raspi-config after rebooting.
cat << EOF | sudo tee -a /etc/wpa_supplicant/wpa_supplicant.conf
ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=netdev
update_config=1
country=UK
EOF

Manually edited country setting - no changes.

A Former User

hmm, something is amiss; still not sure why there is a difference.

given you have ethernet access you could use something like ngrok to get someone you trust to have a look at it for you. if its still unresolved tomorrow I could take a look (although providing access, and ultimately root access, to random strangers on the internet is isn't something i'd reccomend)

Danal

Yeah, this is really odd. If the SD was built from an image, the WPA stuff should work.

Depending on what you want to do... you might consider building an SD again, starting from the Duet image. Once you've done it at least once, it goes pretty quickly.

These are my self-notes for building a new card. Anything that does not start with a # is a potential copy/paste:

# Get your Pi booted and on your network:

# Download image (not lite) from https://duet3d.dozuki.com/Wiki/Getting_Started_With_Duet_3#Section_DuetPi
# Do not unzip it. 
# Etch image to SD card. (search google for balena etcher) 
# Ignore windows error messages for the next drive letter after your SD.  DO NOT format. 
# On the SD card, edit wpa_supplicant.conf for your network
# On the SD card, create a file named 'ssh'.  Empty is fine. 

# Insert SD in Pi and power up. First boot takes an extra minute or two. 
# Find IP address (varies a lot by router)  or try "duet3.local"
# From your PC, enter:
ssh pi@x.x.x.x

# Default password is raspberry  CHANGE IT after you connect for the first time!
# From the Pi command prompt:
passwd

#You now have a running Pi, but it is not completely built 
# to run a Duet 3 printer yet. 

#Set up OS options for Duet Software Framework:
sudo raspi-config 
# Navigate to 5 interface options, then P4 SPI, and 5 again, P3 VNC
# Verify via 
ls /dev/spidev* 
# Look for /dev/spidev0.0
# You may also wish to set country, time zone, etc. with raspi-config

# Now complete setup for duetsoftwareframework. 
wget -q https://pkg.duet3d.com/duet3d.gpg
wget -q https://pkg.duet3d.com/duet3d-unstable.list
sudo mv duet3d.gpg /etc/apt/trusted.gpg.d/
sudo mv duet3d-unstable.list /etc/apt/sources.list.d/duet3d-unstable.list
sudo chown root:root /etc/apt/trusted.gpg.d/duet3d.gpg
sudo chown root:root /etc/apt/sources.list.d/duet3d-unstable.list

sudo apt-get update
sudo apt-get install apt-transport-https
sudo apt-get install duetsoftwareframework

# Verify you can connect to DWC via web server. 
# If you have configuration files (config.g, tool macros, etc) use DWC to upload them now. 

# Update the Pi itself:

sudo apt-get update
sudo apt-get upgrade  (this may take 15 to 60 minutes)

# Reboot is not absolutely required... but... 
sudo reboot


#########################################
# End of required install for Duet 3 Pi #
#########################################

monster

@bearer said in YAT wouldn't respond:

@monster said in YAT wouldn't respond:

I would like to use WiFi!

otherwise you'll just need to put the file on the correct partition, there should be a config.txt file on the correct partition (along with a bunch other files bcm27* and so on)

That helped! Got WiFi working!

A Former User

out of curiosity - which operating system are you running; not windows presumably or?

monster

@bearer said in YAT wouldn't respond:

out of curiosity - which operating system are you running; not windows presumably or?

I feel deeply sorry for not understanding the question
Running what? We were talking about Duet 3 and Pi 4. In this context I'd think you asking about Pi. But that is running onder card I received with Duet 3, so I guess it is some version of Debian.
Running laptop from which I used console to Pi, WebUI or this forum? That is Windows, but that wouldn't interest you I'd guess
Do I miss some part of equation?