Hard fault on printing
-
Hello everyone
I just got my duet 2 wifi installed. upgraded firmware to 3.0 stable.
M115 FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 3.0 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2020-01-03b3I'm getting a hard fault anytime i try to print something. The heat bed will try and heat - but for about 10 seconds before the board resets. Each and everytime.
I was able to successfully PID tune both the hotend and heatbed, and both were able to get up to temperature correctly. The web interface, and everything else seems to be working correctly.
I've erased the flash and flashed with different versions of firmware using firmware fallback procedure 3 (bossa on Mac). v3.0 was the latest one. I've also flashed the firmware via web interface, no amount of firmware flashing/versions seems to solve this issue.
The hard faults only happen during attempts to print.
M122 === Diagnostics === RepRapFirmware for Duet 2 WiFi/Ethernet version 3.0 running on Duet WiFi 1.02 or later Board ID: 08DJM-9178L-L4MSN-6JKF8-3S46N-KS1UP Used output buffers: 1 of 24 (13 max) === RTOS === Static ram: 30516 Dynamic ram: 91764 of which 12 recycled Exception stack ram used: 264 Never used ram: 8516 Tasks: NETWORK(ready,640) HEAT(blocked,1240) MAIN(running,3676) IDLE(ready,156) Owned mutexes: === Platform === Last reset 00:00:20 ago, cause: software Last software reset at 2020-05-03 11:41, reason: Hard fault, spinning module GCodes, available RAM 8180 bytes (slot 1) Software reset code 0x0063 HFSR 0x40000000 CFSR 0x00008200 ICSR 0x0041f803 BFAR 0xbb6661c4 SP 0x20005c04 Task 0x4e49414d Stack: 0041c16b 00400666 61000000 00000000 0044b2b5 00000000 00000001 00000001 00000001 20007364 0044af57 0044af02 476a6000 00000140 4b00ea60 200000b8 00000014 00000000 004529e3 004528de 01000000 00000001 2000ba98 Error status: 0 Free file entries: 10 SD card 0 detected, interface speed: 20.0MBytes/sec SD card longest block write time: 0.0ms, max retries 0 MCU temperature: min 30.8, current 31.6, max 31.9 Supply voltage: min 24.1, current 24.2, max 24.4, under voltage events: 0, over voltage events: 0, power good: yes Driver 0: standstill, SG min/max not available Driver 1: standstill, SG min/max not available Driver 2: standstill, SG min/max not available Driver 3: standstill, SG min/max not available Driver 4: standstill, SG min/max not available Date/time: 2020-05-03 11:41:48 Cache data hit count 40388088 Slowest loop: 3.23ms; fastest: 0.09ms I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0 === Move === Hiccups: 0(0), FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms Bed compensation in use: none, comp offset 0.000 === MainDDARing === Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 === AuxDDARing === Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 === Heat === Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1 === GCodes === Segments left: 0 Stack records: 1 allocated, 0 in use Movement lock held by null http is idle in state(s) 0 telnet is idle in state(s) 0 file is idle in state(s) 0 serial is idle in state(s) 0 aux is idle in state(s) 0 daemon is idle in state(s) 0 queue is idle in state(s) 0 autopause is idle in state(s) 0 Code queue is empty. === Network === Slowest loop: 15.46ms; fastest: 0.00ms Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) HTTP sessions: 1 of 8 - WiFi - Network state is running WiFi module is connected to access point Failed messages: pending 0, notready 0, noresp 0 WiFi firmware version 1.23 WiFi MAC address 84:f3:eb:ea:30:ec WiFi Vcc 3.46, reset reason Turned on by main processor WiFi flash size 4194304, free heap 25464 WiFi IP address 192.168.1.135 WiFi signal strength -76dBm, reconnections 0, sleep mode modem Socket states: 0 0 0 0 0 0 0 0config.g
; Configuration file for Duet WiFi (firmware version 3) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v2.1.8 on Tue Apr 28 2020 23:02:32 GMT-0600 (Mountain Daylight Time) ; General preferences G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"Duet" ; set printer name M667 S1 ; select CoreXY mode ; Network M587 S"REDACTED" P"REDACTED" M551 P"REDACTED" ; set password M552 S1 ; enable network M586 P0 S1 ; enable HTTP M586 P1 S0 ; disable FTP M586 P2 S0 ; disable Telnet ; Drives M569 P0 S1 ; physical drive 0 goes forwards M569 P1 S1 ; physical drive 1 goes backwards M569 P2 S0 ; physical drive 2 goes forwards M569 P3 S1 ; physical drive 3 goes forwards M584 X0 Y1 Z2 E3 ; set drive mapping M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation M92 X200.00 Y200.00 Z400.00 E415 ; set steps per mm M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min) M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min) M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2) M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Axis Limits M208 X-11 Y10 Z0 S1 ; set axis minima M208 X300 Y300 Z200 S0 ; set axis maxima ; Endstops M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop M574 Y2 S1 P"ystop" ; configure active-high endstop for high end on Y via pin ystop M574 Z1 S2 ; configure Z-probe endstop for low end on Z ; Z-Probe M558 P1 C"zprobe.in+zprobe.mod" H5 F120 T6000 ; set Z probe type to unmodulated and the dive height + speeds G31 P500 X-2 Y-16.4 Z1.043 ; Set Z probe trigger value, offset and trigger height M557 X30:270 Y30:270 S80 ; Define mesh grid ; Heaters M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0 M143 H0 S120 ; set temperature limit for heater 0 to 120C M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit M140 H0 ; map heated bed to heater 0 M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1 M143 H1 S280 ; set temperature limit for heater 1 to 280C M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit ; PID tuning hotend M307 H0 A473.6 C164.2 D6.3 V24.1 B0 ; Fans M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on ; Tools M563 P0 D0 H1 F0 ; define tool 0 G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C ; Custom settings are not defined ; Miscellaneous M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss -
Additional info:
All drivers, endstops, thermistors, and z-probe are working and reporting correct values when testing individually. Board is also hooked up to a PanelDue 4.3.
The crash happens only when attempting to print my first print using the duet.
-
Please upgrade to firmware 3.01-RC11 and still if the problem still occurs.
-
@dc42 said in Hard fault on printing:
occurs
Upgrading the firmware, wifiserver and dwc allowed me to finally print. I guess I did not properly flash 3.0-RC11 when I was testing. But confirmed it is working now.
m115 FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 3.01-RC11 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2020-04-30b3
