Macros don't show up on the PanelDue

PayTor

I checked the firmware and it is 1.15c. Also, this the line I use in the config file to create U and V :

M584 X0 Y1 Z2 U3 V4 E5:6:7:8:9 ; Create U and V axes

I can see the the U and V homing buttons on the web interface, but not on the PanelDue.

dc42

Does the machine name show up on PanelDue?

Please try PanelDue firmware version 1.16beta2.

PayTor

I upgraded the firmware. Still the same issue. Here are some pictures of the PanelDue and the web interface:

dc42

Your temperature readings look odd and i am wondering whether your configuration is resulting in a status message that PanelDue is failing to parse. Please share your config.g file.

PayTor

I've disabled the heaters in the config file. Please take a look:

; General preferences
M111 S0 ; Debugging off
G21 ; Work in millimetres
G90 ; Send absolute coordinates…
M555 P1 ; Set firmware compatibility to look like RepRapFirmare

M584 X0 Y1 Z2 U3 V4 E5:6:7:8:9 ; Create U and V axes
M208 X0 Y0 Z-10 U-10 V-10 E0:0:0:0:0 S1 ; Set axis minima
M208 X250 Y615 Z50 U400 V400 E1:1:1:1:1 S0 ; Set axis maxima

; Endstops
M574 X1 Y1 Z1 U1 V1 E1:1:1:1:1 S0 ; Define active S0=LOW or S1=HIGH microswitches

; Drives
M569 P0 S0; Drive 0 goes forwards
M569 P1 S0; Drive 1 goes forwards
M569 P2 S1; Drive 2 goes forwards
M569 P3 S0; Drive 3 goes forwards
M569 P4 S0; Drive 4 goes forwards
M569 P5 S1; Drive 5 goes forwards
M569 P6 S1; Drive 6 goes forwards
M569 P7 S1; Drive 7 goes forwards
M569 P8 S1; Drive 8 goes forwards
M569 P9 S1; Drive 9 goes forwards

M350 X16 Y16 Z16 U16 V16 E16:16:16:16:16 I1 ; Configure microstepping with interpolation
M92 X320 Y320 Z640 U1066.66 V1066.66 E100100100 ; Set steps per mm
M566 X500 Y500 Z1000 U300 V300 E1000:1000:1000:1000:1000 ; Set maximum instantaneous speed changes (mm/min)
M203 X5000 Y5000 Z1000 U1000 V1000 E1000:1000:1000:1000:1000 ; Set maximum speeds (mm/min)
M201 X200 Y200 Z200 U200 V200 E200:200:200:200:200 ; Set accelerations (mm/s^2)
M906 X1200 Y1900 Z800 U1600 V1600 E800:800:800:800:800 I20 ; Set motor currents (mA) and motor idle factor in per cent
M84 S60 ; Set idle timeout

; Heaters
M307 H0 A-1 C-1 D-1
M307 H1 A-1 C-1 D-1
M307 H2 A-1 C-1 D-1
M307 H3 A-1 C-1 D-1
M307 H4 A-1 C-1 D-1
M307 H5 A-1 C-1 D-1
M307 H6 A-1 C-1 D-1
M307 H7 A-1 C-1 D-1

; Detach Fans
M106 P0 H-1
M106 P1 H-1
M106 P2 H-1
M106 P3 H-1
M106 P4 H-1
M106 P5 H-1
M106 P6 H-1
M106 P7 H-1

; Network
M550 PAAA ; Set machine name
M551 Paaa ; Set password
M552 P0.0.0.0 S1 ; Enable network and acquire dynamic address via DHCP

dc42

Thanks, using your config.g file I can replicate the problem. Investigating now.

dc42

It's a bug in DuetWiFiFirmware. Will be fixed in 1.18RC2.

PayTor

Awesome. Thanks for your time and your responsiveness. I'm just wondering when you are planning to release 1.18RC2?

dc42

@PayTor:

Awesome. Thanks for your time and your responsiveness. I'm just wondering when you are planning to release 1.18RC2?

Tomorrow I hope.

dc42

I have just released version 1.18RC2.

PayTor

I just updated the firmware to 1.18RC2 and the issue is fixed. Thank you so much for the help!