Sanity check on Fan setup for laser
-
For the last two days I have been fighting getting my laser to work with my Duet2 WiFi.
Now I am wondering if I have a bigger problem with my fans.
I just converted from 2.0.5 to 3.1.1. I thought things went well overall - even printed a couple of items. But then looking at it more critically I find that the Fan1 (extruder heat sink fan) is on all the time rather than when temp reaching 45 as it should. Fan 0 (parts fan) is not coming on at all even though the slicer calls for it to come on at layer 3 and increase to higher rpm at layer 6. And of course my laser connected to Fan2 does not adjust via laser commands (M3 Sxxx) or turn on or off (M3 S0 or M5). I could really use some help in diagnosing this. I haven't used my printer for about 6 months so I'm really re learning a lot of this. Anyway here are some of the info:Power supply 24 volts
Duet 2 WiFi 1.02
Firmware 3.1.1Here is the config file
; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.3 on Mon Jun 15 2020 11:14:50 GMT-0600 (Mountain Daylight Time); General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"My Printer" ; set printer name
M669 K1 ; select CoreXY mode; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet; Drives
M569 P0 S0 ; physical drive 0 goes backwords
M569 P1 S0 ; physical drive 1 goes backwards
M569 P2 S0 ; physical drive 2 goes backwards
M569 P3 S1 ; physical drive 3 goes forwards
M569 P4 S0 ; physical drive 4 goes backward
M584 X0 Y1 Z2:4 E3 ;two Z Motors connected to driver outputs A and E1
M671 X-20:310 Y0:0 S2 ;Leadscrew at left (connected to Z) and right connected to E1) of X axis
M350 X16 Y16 Z16 E16 U16 I1 ; configure microstepping with interpolation
M92 X101.84 Y104.96 Z402.42 U402.42 E2892.00 ; set steps per mm
M566 X500.00 Y500.00 Z100.00 U100.00 E60.00 ; set maximum instantaneous speed changes (mm/min)
M203 X10000.00 Y10000.00 Z6000.00 U6000.00 E8000.00 ; set maximum speeds (mm/min)
M201 X800.00 Y800.00 Z30.00 U30.00 E120.00 ; set accelerations (mm/s^2)
M906 X1200.00 Y1200.00 Z800.00 U800.00 E500.00 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 X-25 Y-15 Z0 S1 ; set axis minima
M208 X330 Y340 Z300 S0 ; set axis maxima; Endstops
M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S2 ; configure Z-probe endstop for low end on Z; Z-Probe
M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H3 F120 T4800 ; set Z probe type to bltouch and the dive height + speeds
G31 P25 X30 Y-10 Z.48 ; set Z probe trigger value, offset and trigger height
M557 X15:285 Y15:275 P5:5 ; define mesh grid ; define mesh grid
M376 H10; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 R4700 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
M950 F2 C"!fan2" Q1000 ; create fan 2 on pin fan1 and set its frequency
M106 P2 S0 H-1 ; set fan 2 value. Thermostatic control is turned off; Tools
M563 P0 S"E3D_V6" D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C; Custom settings are not defined
M501 ; Load saved parameters from non-volatile memoryHere is a pic of my fan jumpers:
Thanks for looking
George -
The config looks ok for what you describe.
Are you able to control the part cooling fan with the slider in DWC?
Do you have any additional fan commands elsewhere that might be overriding what you have in config.g?
Send M106 P# to get a read back of the current configuration for each fan.
Can you also send M122 and report back.
And send M98 Pconfig.g and report back with any error messages.
-
@Phaedrux said in Sanity check on Fan setup:
M98 Pconfig.g
Thank you for replying.
First off I redid some of the wiring for the fans. Instead of using VIN power I am now supplying the power from a buck to reduce the 24v to 12v via the middle pin on the V Fan Jumper. I also found a loose connection on the Fan0.
So after that Fan0 and Fan1 are working as they are supposed to. However I am back at not getting Fan2 to control the laser. Even when I hook up a simple fan it does not work. Moving the slider on the Dashboard produces nothing. And when I send m106 commands the slider moves but the fan does not. (By the way I checked with two different fans, both know to be working).M98 produces nothing
Here are the m106 status6/17/2020, 5:41:58 PM m106 p0
Fan 0, speed: 0%, min: 10%, max: 100%, blip: 0.10
6/17/2020, 5:41:54 PM m106 p1
Fan 1, speed: 100%, min: 10%, max: 100%, blip: 0.10, temperature: 45.0:45.0C, sensors: 1, current speed: 0%:
6/17/2020, 5:41:50 PM m106 p2
Fan 2, speed: 0%, min: 10%, max: 100%, blip: 0.10And here is the fan part of my config.g
; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
M950 F2 C"!fan2" Q1000 ; create fan 2 on pin fan1 and set its frequency
M106 P2 S0 H-1 ; set fan 2 value. Thermostatic control is turned offLastly here is the M122:
6/17/2020, 5:36:13 PM === Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.1.1 running on Duet WiFi 1.02 or later
Board ID: 08DGM-9T6BU-FG3SJ-6JKD4-3S46L-TUW7D
Used output buffers: 3 of 24 (20 max)
=== RTOS ===
Static ram: 27980
Dynamic ram: 93984 of which 60 recycled
Exception stack ram used: 264
Never used ram: 8784
Tasks: NETWORK(ready,368) HEAT(blocked,1216) MAIN(running,1816) IDLE(ready,80)
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:00:41 ago, cause: power up
Last software reset at 2020-06-17 10:03, reason: User, spinning module GCodes, available RAM 8784 bytes (slot 2)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task MAIN
Error status: 0
MCU temperature: min 31.8, current 36.0, max 36.0
Supply voltage: min 23.7, current 23.8, max 24.0, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2020-06-17 17:35:47
Cache data hit count 66412690
Slowest loop: 7.78ms; fastest: 0.14ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 16.4ms, write time 0.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 23.25ms; fastest: 0.00ms
Responder states: HTTP(2) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 2 of 8- WiFi -
Network state is active
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.23
WiFi MAC address cc:50:e3:6a:85:90
WiFi Vcc 3.35, reset reason Unknown
WiFi flash size 4194304, free heap 24448
WiFi IP address 192.168.1.73
WiFi signal strength -67dBm, reconnections 0, sleep mode modem
Socket states: 4 0 0 0 0 0 0 0
I don't see where I am off.
George
- WiFi -
