How to ping Z-probe state

Veti

i dont see the probe status in the object model

https://duet3d.dozuki.com/Wiki/GCode_Meta_Commands

NexxCat

if sensors.endstops[3].triggered
    M106 P2 S255 ;increase power of light to full power

Just change the "3" to the correct end-stop number for your z-probe. This likely won't work with the BLTouch because it is only triggered briefly, but for an inductive sensor or the likes, it would work.

code7

@NexxCat When I run what you have suggested I receive the following error. Do you know what I may be overlooking?

Error: in file macro line 1 column 4: meta command: array index out of bounds

NexxCat

@code7 What Z-Probe are you using?

code7

I'm using a conductive Z-probe that triggers when the nozzle makes contact with the bed.

NexxCat

@code7 ~~Does it show as an end stop in DWC under "Machine Specific"? There's a readout of the end stops on the right hand side, labelled beginning 0.~~

~~EDIT: Disregard the above. Z-Probes are elsewhere in the object model it seems. I'm not 100% sure as I'm not at my printer right now, but maybe try looking at sensors.zprobes[0].value~~

~~That's a guess based on looking at the code.~~

EDIT 2: Try this:

if sensors.probes[0].value[0] > 1
    M106 P2 S255 ;increase power of light to full power

code7

@NexxCat Thanks. I'll test it out. This is my first attempt using meta commands.

If I wanted to trigger another event when the probe is not triggered would I just swap the direction of the carrot ">" to "<" ?

Also, can you give me an idea of how I can implement the "else" syntax or another syntax in another macro to stop this routine?

NexxCat

@code7 You could try something similar to this, which is also a bit neater

if sensors.probes[0].value[0] != 0
    ; Z-Probe triggered
else
    ; Z-Probe not triggered

; Non conditional gcode continues here

This would be the reverse, checking for the probe not being triggered:

if sensors.probes[0].value[0] == 0
    ; Z-Probe not triggered
else
    ; Z-Probe triggered

; Non conditional gcode continues here

dc42

@code7 said in How to ping Z-probe state:

What command can I send from the console to check the current Z-probe state?

You mean the triggered/not triggered status?

22/09/2020, 12:11:06 	echo sensors.probes[0].value[0]>=sensors.probes[0].threshold
false

code7

@NexxCat Thanks. This works great.

Is is possible to continually run this code in real time while printing?

@dc42 Yes that is what I meant. Thanks.

NexxCat

@code7 You can use daemon.g for that, but I have no experience with using it. Check this thread: https://forum.duet3d.com/topic/14701/daemon-g-usage-cases

code7

@dc42 Do you see any issues with me using daemon.g to continually check the state of the probe only during print moves? I currently have a macro that runs when the filament is retracted and ends when the filament is un-retracted. I need a way to turn down a power supply within 1 second of the probe losing contact with the conductive metal print.

dc42

@code7 said in How to ping Z-probe state:

@dc42 Do you see any issues with me using daemon.g to continually check the state of the probe only during print moves? I currently have a macro that runs when the filament is retracted and ends when the filament is un-retracted. I need a way to turn down a power supply within 1 second of the probe losing contact with the conductive metal print.

You can do that using a loop in daemon.g, however I suggest you include a G4 delay in that loop of perhaps 500ms, to prevent it using too much CPU time.

code7

@dc42 OK. I'll give it a try.

In regards to running real-time loops in daemon.g, would it be possible to use a loop in daemon.g to call for a variable that can reduce the feedrate mid-print to 1% while a long single line segment is being printed? Ideally I would be able to pause mid deposition, but I know the current command needs to complete before a pause can be invoked.