Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Temprature sensor error unknown temperature sensor channel

    Scheduled Pinned Locked Moved
    Firmware installation
    6
    91
    4.7k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • JTMundefined
      JTM @Phaedrux
      last edited by

      @Phaedrux its a huge file to cut and paste?

      1 Reply Last reply Reply Quote 0
      • JTMundefined
        JTM @Phaedrux
        last edited by

        @Phaedrux i assume you only need the start file?
        G90
        M82
        M106 S0
        M140 S110
        M190 S110
        M104 S285 T0
        M109 S285 T0
        G28 ; home all axes
        T0
        ; process Process1-1
        ; layer 1, Z = 0.225
        T0
        G92 E0.0000
        G1 E-8.0000 F5502
        ; feature skirt
        ; tool H0.225 W1.500
        G1 Z0.225 F1500
        G1 X41.799 Y46.303 F3900
        G1 E0.8000 F5502
        G92 E0.0000
        G1 X42.105 Y46.033 E0.0601 F2640

        Phaedruxundefined 1 Reply Last reply Reply Quote 0
        • JTMundefined
          JTM @Phaedrux
          last edited by

          @Phaedrux this is the last code:
          ; layer end
          M104 S0 ; turn off extruder
          M140 S0 ; turn off bed
          G91;
          G1 Z50;
          G92;
          M84 ; disable motors

          1 Reply Last reply Reply Quote 0
          • Phaedruxundefined
            Phaedrux Moderator
            last edited by

            I think this is an issue with simplify 3d targeting the right heaters.

            Try this, go to stay folder and create a new file called start.g inside it put T0 and save it.

            Z-Bot CoreXY Build | Thingiverse Profile

            JTMundefined 1 Reply Last reply Reply Quote 0
            • JTMundefined
              JTM @Phaedrux
              last edited by

              @Phaedrux In my config file?

              1 Reply Last reply Reply Quote 0
              • Phaedruxundefined
                Phaedrux Moderator
                last edited by

                Well you should have a T0 at the end of your config file as well.

                But I mean creating a new file in the sys folder called start.g with T0 in it as well.

                Start.g gets run when you start a print.

                Z-Bot CoreXY Build | Thingiverse Profile

                JTMundefined 1 Reply Last reply Reply Quote 0
                • JTMundefined
                  JTM @Phaedrux
                  last edited by

                  @Phaedrux Thanks so much mate, ill try it out

                  1 Reply Last reply Reply Quote 0
                  • Phaedruxundefined
                    Phaedrux Moderator @JTM
                    last edited by Phaedrux

                    @JTM said in Temprature sensor error unknown temperature sensor channel:

                    M104 S285 T0
                    M109 S285 T0

                    I would suggest editing your slicer start gcode to remove the T0 from the end of those commands. And put a T0 at the very start of your slicer start gcode.

                    Z-Bot CoreXY Build | Thingiverse Profile

                    JTMundefined 1 Reply Last reply Reply Quote 0
                    • JTMundefined
                      JTM @Phaedrux
                      last edited by

                      @Phaedrux I have tried changing the T0 around and no difference really. I keep getting a M140 error which is the heated bed which i don't have connected. I would start a print and ill get these errors which i close and resume print as its been paused automatically due to a heater fault. if i start the print it will run for 600 seconds and stop. the strange thing is once that occurs as long as i dont switch off the printer or reboot the board i can send a file to print and it does without a problem. Maybe i need to disable the heated bed?

                      Phaedruxundefined 1 Reply Last reply Reply Quote 0
                      • Phaedruxundefined
                        Phaedrux Moderator @JTM
                        last edited by

                        @JTM said in Temprature sensor error unknown temperature sensor channel:

                        I keep getting a M140 error which is the heated bed which i don't have connected.

                        Ok, so you don't have your heated bed connected? Well that would certainly cause an error since it will try to heat it, see that the temperature isn't rising, and through a heater fault.

                        If you don't have it connected remove the commands to heat it.

                        Z-Bot CoreXY Build | Thingiverse Profile

                        1 Reply Last reply Reply Quote 0
                        • JTMundefined
                          JTM
                          last edited by

                          so delete the M140 command?

                          1 Reply Last reply Reply Quote 0
                          • Phaedruxundefined
                            Phaedrux Moderator
                            last edited by

                            The easiest way would be to just tell the slicer you don't have a heated bed so that it doesn't generate commands to heat it.

                            Z-Bot CoreXY Build | Thingiverse Profile

                            1 Reply Last reply Reply Quote 0
                            • JTMundefined
                              JTM
                              last edited by

                              Thats gotta be it ! i never realized the slicer was sending a command to heat the bed. The printer i have been using must have the heated bed disabled in config as its a mains supply heated bed. I have a print running and in about an hour i will delete the heated bed command and see if that fixes the problem ! thanks so much for the help !

                              One thing that frustrates me is the homing of Z is really slow its showing as 2mm/sec how can i increase that speed? The initial raising of the bed is at 2mm/sec but after the probe has been activated the movement is much faster. It moves down then moves up to meet the nozzle faster than the initial z axis movement up. i looked in the config files M558 which shows

                              M558 P9 C"^zprobe.in" H5 F100 T2000 ; set Z probe type to bltouch and the dive height + speeds

                              Is the H5 the speed setting for the initial probing?

                              Thanks in advance 🙂

                              1 Reply Last reply Reply Quote 0
                              • Phaedruxundefined
                                Phaedrux Moderator
                                last edited by

                                You can modify your homeall.g files to add a faster probe first and then a slower probe afterwards.

                                Where you have a G30 to probe the bed, change it to add a M558 F command to change the feed rate, then probe. First fast, then slow. Like this:

                                M558 F400 A1
                                G30
                                M558 F100 A5
                                G30
                                

                                The A1 says just do it once, the A5 says probe until two consecutive results are basically the same up to 5 times.

                                Z-Bot CoreXY Build | Thingiverse Profile

                                1 Reply Last reply Reply Quote 0
                                • First post
                                  Last post
                                Unless otherwise noted, all forum content is licensed under CC-BY-SA