I need SD card files for duet 3 6HC

Phaedrux

Is there anything on the PanelDue screen at all?

You may need to update the firmware.

https://duet3d.dozuki.com/Wiki/PanelDue_Firmware_update

For RRF 3.1.1 I would use 1.24 on the PanelDue.

dc42

Send M503 through USB to check that it can read the SD card.

Ironman777

@Phaedrux Screen didnt do anything. i uploaded firmware update via usb. Upload system files button in Duet Web Control. Check it is in the Duet's '0:sys' folder. If necessary, rename the file to 'PanelDueFirmware.bin'. still no luck

Ironman777

@dc42 M503 VIA USB no results. Do you have to have PanelDue to resume print after power failure?

Phaedrux

@Ironman777 said in I need SD card files for duet 3 6HC:

Do you have to have PanelDue to resume print after power failure?

No, you just need to be able to send the command to resume the print.

https://duet3d.dozuki.com/Wiki/Setting_up_to_resume_a_print_after_a_power_failure

@Ironman777 said in I need SD card files for duet 3 6HC:

@Phaedrux Screen didnt do anything. i uploaded firmware update via usb. Upload system files button in Duet Web Control. Check it is in the Duet's '0:sys' folder. If necessary, rename the file to 'PanelDueFirmware.bin'. still no luck

You'll need to follow the actual instructions for updating the paneldue firmware using USB and Bossa.

Ironman777

This post is deleted!

Ironman777

@Phaedrux I can’t get resume after power failure to work. This is in my config M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E5 F1000" ; set voltage thresholds and actions to run on power loss.

I also created a resurrect-prologue file M116 ; Wait for temps
G28 ; Home all
M83 ; relative extrusion
G1 D2 3600 ; undo retraction

It creates a resume.g file when I run M916 it says error file not found

At one point in time this worked for my duet2 has any of the commands changed? I print for 100-200 hours at a time so this is very important.

Phaedrux

@Ironman777 said in I need SD card files for duet 3 6HC:

It creates a resume.g file when I run M916 it says error file not found

Can you post the file that gets created when power is lost?

Post your resurrect.g and resurrect-prologue.g as well.

Ironman777

@Phaedrux This is what gets created after power failure ; resume.g
; called before a print from SD card is resumed
;
; generated by RepRapFirmware Configuration Tool v3.1.10 on Fri Dec 11 2020 20:02:22 GMT-0800 (Pacific Standard Time)
G1 R1 X0 Y0 Z5 F6000 ; go to 5mm above position of the last print move
G1 R1 X0 Y0 ; go back to the last print move
M83 ; relative extruder moves
G1 D2 F3600 ; extrude 10mm of filament

0:/sys/ressurect-prolague.g
M116 ; Wait for temps
G28 ; Home all
M83 ; relative extrusion
G1 D2 3600 ; undo retraction

This is in my config M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E5 F1000" ; set voltage thresholds and actions to run on power loss.

no ressurect.g file is created only resume.g

Phaedrux

@Ironman777 said in I need SD card files for duet 3 6HC:

0:/sys/ressurect-prolague.g

Does that typo exist in the actual file name?

G1 D2 3600 ; undo retraction

Or that one?

Ironman777

@Phaedrux the actual file name is ressurect-prolague.g
and yes G1 D2 3600 ; undo retraction D2 is my extruder pin there is no E on Duet3

Phaedrux

If that's the case then the spelling is wrong and that's why it can't find the file.