1.19beta7 and WiFi connect

dc42

I've just released DuetWiFiServer 1.18beta8. Please try it in case it helps. It disables persistence and auto-connect at startup. At the very least, it should provide a more detailed error message (to PanelDue and USB) if it fails to connect when you send M552 S1.

The P parameter of M552 isn't used on the Duet WiFi.

juniormajpr

just uploaded WiFiServer beta8 and everything works as expected.
only get an error once while trying connect/disconnect/change mode now for 30+ times.
the error was:

[[language]]
WiFi reported error: Unexpected WiFi state 'idle' while trying to connect to

unfortunately i hurried to much, and i resettet the Duet, so i can't say if the above error is "self-healing" or not (retry after a timeout or something like this).
but it didn't occur a second time

@dc42: thx!

juniormajpr

upps… did it again...
after some hours online a reboot was needed, and afterwards no WiFi connection was establised.

[[language]]
>>> M552
SENDING:M552
WiFi module is idle
>>> M552 S1
SENDING:M552 S1
WiFi reported error: Unexpected WiFi state 'idle' while trying to connect to
Wifi module is idle

And no, it isn't an error of me that the "currentSsid" which should come after "… connect to ..." is missing.
So i think the config couldn't be read although M587 did list the known SSIDs

[[language]]
>>> M587
SENDING:M587
Remembered networks:
xxxx yyyy z.z

dc42

Thanks, that gives me something to go on. If you try sending M552 S1 a few more times, does it connect eventually? If not, try M552 S-1 followed by M552 S1.

juniormajpr

nope… this time no changes...

[[language]]
>>> M552 S1
SENDING:M552 S1
WiFi reported error: Unexpected WiFi state 'idle' while trying to connect to
Wifi module is idle
>>> M552 S1
SENDING:M552 S1
WiFi reported error: Unexpected WiFi state 'idle' while trying to connect to
Wifi module is idle
>>> M552 S1
SENDING:M552 S1
WiFi reported error: Unexpected WiFi state 'idle' while trying to connect to
Wifi module is idle
>>> M552 S1
SENDING:M552 S1
WiFi reported error: Unexpected WiFi state 'idle' while trying to connect to
Wifi module is idle
>>> M552 S1
SENDING:M552 S1
WiFi reported error: Unexpected WiFi state 'idle' while trying to connect to
Wifi module is idle
>>> M552 S1
SENDING:M552 S1
WiFi reported error: Unexpected WiFi state 'idle' while trying to connect to
Wifi module is idle
>>> M552 S1
SENDING:M552 S1
WiFi reported error: Unexpected WiFi state 'idle' while trying to connect to
Wifi module is idle
>>> M552 S-1
SENDING:M552 S-1
WiFi module stopped
>>> M552 S1
SENDING:M552 S1
WiFi module started
WiFi reported error: Unexpected WiFi state 'idle' while trying to connect to
Wifi module is idle
>>> M552 S1
SENDING:M552 S1
WiFi reported error: Unexpected WiFi state 'idle' while trying to connect to
Wifi module is idle
>>> M552 S1
SENDING:M552 S1
WiFi reported error: Unexpected WiFi state 'idle' while trying to connect to
Wifi module is idle
>>> M552 S-1
SENDING:M552 S-1
WiFi module stopped
>>> M552 S1
SENDING:M552 S1
WiFi module started
WiFi reported error: Unexpected WiFi state 'idle' while trying to connect to
Wifi module is idle

15-30 seconds between each try.

juniormajpr

ok tested a little bit more… there seems to be a bug with EEPROM put/get.

szenario: all known SSIDs are deleted with M588 S"" and all AP configurations are deleted also with M589 S"".

[[language]]
M588 S"*"
ok
M589 S"*"
ok
M587
No remembered networks
ok

after that i established an AP config which is listed correctly with M587

[[language]]
M589 S"duet" P"duet" I192.168.1.1
ok
M587
Remembered networks:
duet
ok

when i try to start AP mode -> error, but AP config seems to be still stored

[[language]]
M552 S2
ok
WiFi reported error: Failed to start access point
Wifi module is idle
M587
Remembered networks:
duet
ok

add an client config and list again known configs the AP config is gone

[[language]]
M587 S"test" P"test"
ok
M587
Remembered networks:
test

dc42

M587 should not list the AP name as a remembered network if you are using beta 8 of DuetWiFiFirmware. Please check which version you are running. Tomorrow I'll check for coding errors in that area.

juniormajpr

WifiServer beta8 and RRF beta8. see below:

[[language]]
M122
=== Diagnostics ===
Used output buffers: 1 of 32 (1 max)
=== Platform ===
RepRapFirmware for Duet WiFi version 1.19beta8 running on Duet WiFi 1.0
Board ID: xxxx
Static ram used: 20900
Dynamic ram used: 96084
Recycled dynamic ram: 1800
Stack ram used: 3960 current, 4784 maximum
Never used ram: 7504
Last reset 00:00:47 ago, cause: power up
Last software reset reason: User, spinning module GCodes, available RAM 7180 bytes (slot 2)
Software reset code 0x0003, HFSR 0x00000000, CFSR 0x00000000, ICSR 0x00400000, BFAR 0xe000ed38, SP 0xffffffff
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms
MCU temperature: min -210.4, current 41.4, max 41.5
Supply voltage: min 0.1, current 0.5, max 0.8, under voltage events: 0, over voltage events: 0
Driver 0: ok
Driver 1: ok
Driver 2: ok
Driver 3: ok
Driver 4: ok
Date/time: 1970-01-01 00:00:00
Slowest main loop (seconds): 0.001695; fastest: 0.000027
=== Move ===
MaxReps: 0, StepErrors: 0, MaxWait: 0ms, Underruns: 0, 0
Scheduled moves: 0, completed moves: 0
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
Probe change coordinates:
=== Heat ===
Bed heater = 0, chamber heater = -1
=== GCodes ===
Segments left: 0
Stack records: 2 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is ready with "M122" in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
Code queue is empty.
Network state is running
WiFi module is idle
WiFi firmware version 1.19beta8
WiFi MAC address aa:bb:cc:dd:ee:ff
WiFi Vcc 3.10, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 41104
HTTP sessions: 0 of 8
Socket states:  0 0 0 0 0 0 0 0
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
ok

dc42

OK, I found the bug, it's purely a reporting issue. If you have no remembered networks but you have specified an access point name, then when you list remembered networks it prints the access point name. After you have added a remembered network, you can still retrieve the own access point name by sending M589. The fix will be in the next beta.

I still haven't worked out why it's trying to connect to an empty SSID. I'll look at that later today.

juniormajpr

@dc42: as per definition the passphrase within the AP mode hast to be at least 8 chars long, i think it would be reasonable to check for valid M589 input (i think ssid min 0 max 32 chars and passphrase min 8-64 chars).
try:

[[language]]
M552 S0
ok
WiFi module started

M589 S"test" P"test" I192.168.1.1
ok
M552 S2
ok
WiFi module started
WiFi reported error: Failed to start access point
Wifi module is idle

M589 S"test" P"testtest" I192.168.1.1
ok
M552 S2
ok
Wifi module is providing access point test, IP address 192.168.1.1

dc42

Thanks for the suggestion, I'll implement it in the next beta.

I can't reproduce the problem with failing to connect and not displaying the SSID name, but I've built a new DuetWiFiServer.bin with some changes that may help and put it at https://dl.dropboxusercontent.com/u/19369680/DuetWiFiServer.bin. Please try it.

juniormajpr

will give it a try. will give feedback tomorrow.
is there the possibility to erase the ESP (incl. flash) completly from SAM/RRF? or only via ISP?

juniormajpr

@dc: i think i found the reason, why an empty config was read…

SocketServer.cpp - row 64

[[language]]
for (size_t i = 1; i <= MaxRememberedNetworks; ++i)

shouldn't it be```
[[language]]
for (size_t i = 0; i <= MaxRememberedNetworks; ++i)

same in row 83

or better (i think) not to waste one slot at the beginning (row 64, 83, 112, 521,…)

[[language]]
for (size_t i = 0; i < MaxRememberedNetworks; i++)

dc42

The first entry is the configuration for the WiFi module as an access point. So the count starts from 1 when it is searching for a remembered SSID.

juniormajpr

hmmm… once again:

[[language]]
for (int8_t i = 0; i < num_ssids; ++i)
{
	if ((strongestNetwork < 0 || WiFi.RSSI(i) > WiFi.RSSI(strongestNetwork)) && RetrieveSsidData(WiFi.SSID(i).c_str(), ssidData))
	{
		strongestNetwork = i;
	}
}

WiFi.RSSI's and WiFi.SSID's parameters are a zero based index from prior discovered SSIDs by blocking WiFi.scanNetworks(false, true)
At this point we are looking at the wrong index. aren't we? ++i -> i++

juniormajpr

@dc: 1.19beta8+1 doesn't change the WiFi behaviour. but can you plz. confirm/check the above post?

dc42

Using ++i or i++ does exactly the same thing if the operand has primitive type and you don't use the value within the same expression, as in this case.

Zest

I just got a Duet Wifi and I'm having a hell of a time with the WIFI setup. I have tried flashing 1.18 stable as well as 1.19 beta 8. I first attempted upgrades via M997 but eventually tried the erase/reset/reload via samba. I have gotten it to connect once or twice but it seems whenever I edit config.g to uncomment M552 S1 it fails to connect again after reboot. I have fiddled with it quite a bit since then and haven't been able to get it to talk to my router again.

I've noticed a couple things

when using 1.18 M552 will say that the board is in AP mode but I can't see it in my list of WIFI networks.
when it does this it also says hostname is some bunch of gibberish ascii characters
when using 1.19 Beta 8 M587 returns the two remembered networks I have configured in my SetNetwork macro however when I do a M552 S1 I get

M587
SENDING:M587
Remembered networks:
seawest
seawest 5G
M552 S1
SENDING:M552 S1
WiFi reported error: no known networks found
Wifi module is idle

I'm starting to think the board is faulty. Is there anything else I can try? It's almost as if the WIFI module is retaining some kind of garbage. Is there a way to purge everything so I'm starting fresh? SD Card, memory, everything?

dc42

The "no known networks found" message means that it did a network scan and didn't find either of the SSIDs you configured. How strong is the signal from your router where the Duet is? Is the Duet surrounded by metalwork that would attenuate the signal?

The Duet WiFi does 2.4GHz only, and I presume seawest 5G is a 5GHz access point.

I think access point names are case sensitive. Is 'seawest' exactly how your access point name appears when you connect to it from a smartphone, tablet etc. ?

Zest

wow thanks for the quick reply. seawest is the name of my 2.4 Ghz network and my seawest 5G is my 5 Ghz network. Both are off of the same ASUS router that sits about 10 feet away. The names are case sensitive and exactly as they're seen from my iphone. My password is alphanumeric and only contains letters and a number.

The thing that makes me suspicious that the board is bad is the fact that I don't see "Duet WIFI" when the board thinks it's in AP mode when using 1.18. Are there any debug commands I can use to test the functionality of the WIFI module itself? I was able to get the board to connect a handful of times and it seemed tied to loading a new WIFI firmware. However, I have tried reloading firmware several times since then and I haven't been able to re-establish a connection.

I WAS able to connect to the "Duet WIFI" SSID but only once. When that occurred I could see my neighbor's APs as well as my own. I was also able to get into the web interface but as soon as I uncommented "M552 S1" and rebooted I had the same problems all over again and could not reconnect.