Bed Levelling with independent Z motors error
-
Hi All,
I'm trying to setup z gantry leveling in a cartesian printer with independent z motors.
I've read through https://duet3d.dozuki.com/Wiki/Bed_levelling_using_multiple_independent_Z_motors and I can't seem to get it to work. Can you see any errors in my config.g, bed.g homeall.g which may cause this?
I'm still working on getting my 3hc board working, but all the z drivers are connected to the main duet3 6hc board.
I get the following error
"Error: Number of calibration factors (2) not equal to number of leadscrews (4)."config.g
; Configuration file for Duet 3 (firmware version 3) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v3.2.3 on Wed Mar 31 2021 21:23:47 GMT+1100 (Australian Eastern Daylight Time) ; General preferences G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"duet" ; set printer name ; Network M552 P0.0.0.0 S1 ; enable network and acquire dynamic address via DHCP M586 P0 S1 ; enable HTTP M586 P1 S0 ; disable FTP M586 P2 S0 ; disable Telnet ; Drives M569 P0.0 S0 ; x physical drive 0.0 goes forwards: idex 1 M569 P0.1 S1 ; u physical drive 0.1 goes forward: idex 2 M569 P0.2 S0 ; y physical drive 0.2 goes backwards: y axis M569 P0.3 S0 ; Z axis 1 M569 P0.4 S0 ;z axis 2 M569 P0.5 S1 ;Extruder 1 M569 P1.0 S1 ; extruder 2 M584 X0.0 Y0.2 U0.1 Z0.3:0.4 E0.5:1.0 ; set drive mapping: x connected 0.0, u to 0.1, y 0.2, two z motors, one connected 0.3, the other to 1.0, Two extruders, one to 0.4, second to 0.5 M671 X-120:440 Y185:185 S1 ; leadscrews at left (connected to Z) and right (connected to E1) of X axis ; Axis Limits M208 x-100 u0 y0 z0 s1 ; set axis minima m208 x420 u524 y380 z400 s0 ; higher u moves extruder 2 to right M350 X16 U16 Y16 Z16 E16 i1 ; configure microstepping with interpolation M92 X80.00 U80 Y80.00 Z400.00 E394.20:394.2 ; set steps per mm M566 X700.00 U700 Y700.00 Z60.00 E120.00 ; set maximum instantaneous speed changes (mm/min) M203 X12000.00 U12000 Y12000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min) M201 X1500.00 U1500 Y1500.00 Z20.00 E250.00 ; set accelerations (mm/s^2) M906 X1000 u1000 Y1000 Z700 E800:800 I30 ; set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout M911 S21.0 R23.0 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; if voltage drops <21v ; Endstops M574 X1 S1 P"io2.in" ; configure active-high endstop for low end on X via pin io4.in M574 Y1 S1 P"io3.in" ; configure active-high endstop for high end on Y via pin io3.in M574 U2 S1 P"!io5.in" M915 U R0 F0 M574 Z1 S2 ; configure Z-probe endstop for low end on Z ; Z-Probe M950 S0 C"io7.out" ; create servo pin 0 for BLTouch M558 P9 C"io7.in" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds;G31 P500 X-41 Y5 Z2.5 ; set Z probe trigger value, offset and trigger height G31 P500 X32.5, Y-42 z.66 M557 X60:420 Y0:330 S50 ; define mesh grid M280 P0 S90 ; Heaters ;Bed M308 S0 P"temp0" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin temp0 - Heated BED M950 H0 C"out1" T0 ; create bed heater output on out2 and map it to sensor 0 M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit M140 H0 ; map heated bed to heater 0 M143 H0 S120; set temperature limit for heater 0 to 120C ;Extruder 1 M308 S1 P"temp1" Y"thermistor" T165000 B4725 c7.06e-8 R2200 ; configure sensor 1 as thermistor on pin temp1 - Extruder 1 M950 H1 C"out2" T1 ; create nozzle heater output on out1 and map it to sensor 1 M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit M143 H1 S280 ; set temperature limit for heater 1 to 280C ;Extruder 2 M308 S2 P"temp2" Y"thermistor" T100000 B4725 c7.06e-8 ; configure sensor 1 as thermistor on pin temp1 - Extruder 1 M950 H2 C"out3" T2 ; create nozzle heater output on out1 and map it to sensor 1 M307 H2 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit M143 H2 S280 ; set temperature limit for heater 1 to 280C ; Fans ; Extruder 1 - part fan M950 F0 C"out7" Q500 ; create fan 0 on pin out7 and set its frequency m106 p0 s0 ; set fan 0 value. Thermostatic control is turned on ; Extruder 2 - hot end fan M950 F1 c"out8" Q500 m106 p1 s1 h2 ; Extruder 2 - part fan ;Part fan M950 F2 c"out9" q500 ; create fan 1 on pin out8 and set its frequency M106 P2 S0 ; Custom settings are not defined ;''' Tool configuration section of config.g''' ;''' Create a tool that uses the low end (X) carriage''' M563 P0 S"Extuder A" D0 H1 F0 ; tool 0 uses extruder 0, heater 1 and fan 0 G10 P0 X0 Y0 Z0 S0 R0 ; set tool 0 offsets and temperatures M591 P1 C"io4.in" S1 D0 ; filament monitor connected to E0 endstop M591 P2 C"io1.in" S1 D1 ;''' Create a tool that uses the high end (U) carriage''' M563 P1 S"Extruder B" D1 H2 X3 F3 ; tool 1 uses extruder 1, heater 2, fan 2, and maps X to U G10 P1 Y2.5 U0 Z7.9 S0 R0 ;adjusts extrude 2 offset. larger number, the closer to bed, larger y moves to front M671 X80:460:460:80 Y300:300:-35:-35 P0.5 ; Miscellaneous M501 ; load saved parameters from non-volatile memory M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z2.7 E-5 F1000" ; set voltage thresholds and actions to run on power loss M207 S2.0 F2400 Z.6 M929 s1bed.g
; bed.g ; called to perform automatic bed compensation via G32 ; ; generated by RepRapFirmware Configuration Tool v3.2.3 on Wed Mar 31 ;2021 21:23:47 GMT+1100 (Australian Eastern Daylight Time) G28; home ;M401 ; deploy Z probe G30 P0 X80 Y150 Z-99999 ; probe near an adjusting screw G30 P1 X460 Y150 Z-99999 s2; probe near an adjusting screw ;M402 ; retract probehomeall.g
M400 ;M913 x70 ; drop motor current to 70% M400 G91; relative positioning G1 H2 Z10 F12000 ; lift Z relative to current position G1 H1 x-520.5 F8000 ; move quickly to X axis endstop and stop there (first pass) G1 H2 x5 F12000 ; go back a few mm G1 H1 x-520.5 F7000 ; move slowly to X axis endstop once more (second pass) G1 H2 Z-10 F6000 ; lower Z again G90 ; absolute positioning M400 ;M913 U70 ; drop motor current to 70% M400 G91; relative positioning G1 H2 Z10 F6000 ; lift Z relative to current position G1 H1 U520.5 F8000 ; move quickly to X axis endstop and stop there (first pass) G1 H2 U-5 F12000 ; go back a few mm G1 H1 U520.5 F7000 ; move slowly to X axis endstop once more (second pass) G1 H2 Z-10 F6000 ; lower Z again G90 ; absolute positioning M400 ;M913 U100 ; return current to 100% ;G91 ; relative positioning ;G1 H2 Z5 F6000 ; lift Z relative to current position ;G1 H1 Y-455 F1800 ; move quickly to Y axis endstop and stop there (first pass) ;G1 H2 Y5 F6000 ; go back a few mm ;G1 H1 Y0 F360 ; move slowly to Y axis endstop once more (second pass) ;G1 H2 Z-5 F6000 ; lower Z again ;G90 ; absolute positioning G91 ; relative positioning G1 H2 Z5 F6000 ; lift Z relative to current position G1 H1 Y-455 F1800 ; move quickly to Y axis endstop and stop there (first pass) G1 H2 Y5 F6000 ; go back a few mm G1 H1 Y0 F360 ; move slowly to Y axis endstop once more (second pass) G1 H2 Z-5 F6000 ; lower Z again G90 ; absolute positioning G91 ; relative positioning G1 H2 Z5 F6000 ; lift Z relative to current position G90 ; absolute positioning ;G1 X56 Y10 F6000 ; go to first probe point ;g28 u G1 X225 Y130 F6000 ;G30 s2 g30 G1 x -98 ;g10 l2 p1 u0 y2.2 z-.86 ;g10 l2 p1 u0 y-6 z11.5M122
9/3/2021, 10:34:54 AM M122 === Diagnostics === RepRapFirmware for Duet 3 MB6HC version 3.3 (2021-06-15 21:45:47) running on Duet 3 MB6HC v1.01 or later (standalone mode) Board ID: 08DJM-956L2-G43S8-6J1D6-3S46T-KU2QF Used output buffers: 3 of 40 (36 max) === RTOS === Static ram: 150904 Dynamic ram: 93228 of which 336 recycled Never used RAM 106868, free system stack 152 words Tasks: NETWORK(ready,27.1%,230) ETHERNET(notifyWait,0.2%,117) HEAT(notifyWait,0.0%,325) Move(notifyWait,0.0%,284) CanReceiv(notifyWait,0.0%,944) CanSender(notifyWait,0.0%,362) CanClock(delaying,0.0%,333) TMC(notifyWait,8.0%,93) MAIN(running,63.7%,1110) IDLE(ready,1.0%,29), total 100.0% Owned mutexes: === Platform === Last reset 00:11:17 ago, cause: software Last software reset at 2021-09-03 10:23, reason: User, GCodes spinning, available RAM 106868, slot 1 Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task MAIN Freestk 0 n/a Error status: 0x00 Step timer max interval 154 MCU temperature: min 46.5, current 46.8, max 47.8 Supply voltage: min 23.7, current 23.8, max 23.9, under voltage events: 0, over voltage events: 0, power good: yes 12V rail voltage: min 12.0, current 12.1, max 12.2, under voltage events: 0 Heap OK, handles allocated/used 99/0, heap memory allocated/used/recyclable 2048/12/12, gc cycles 0 Driver 0: position 34200, standstill, reads 22842, writes 21 timeouts 0, SG min/max 0/282 Driver 1: position 15360, standstill, reads 22841, writes 22 timeouts 0, SG min/max 0/328 Driver 2: position 2264, standstill, reads 22845, writes 19 timeouts 0, SG min/max 0/553 Driver 3: position 41920, standstill, reads 22845, writes 19 timeouts 0, SG min/max 0/88 Driver 4: position 0, standstill, reads 22845, writes 19 timeouts 0, SG min/max 0/107 Driver 5: position 0, standstill, reads 22850, writes 14 timeouts 0, SG min/max 0/0 Date/time: 2021-09-03 10:34:54 Slowest loop: 16.20ms; fastest: 0.05ms === Storage === Free file entries: 9 SD card 0 detected, interface speed: 25.0MBytes/sec SD card longest read time 7.7ms, write time 2.3ms, max retries 0 === Move === DMs created 125, maxWait 20881ms, bed compensation in use: none, comp offset 0.000 === MainDDARing === Scheduled moves 21, completed moves 21, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1 === AuxDDARing === Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1 === Heat === Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1 === GCodes === Segments left: 0 Movement lock held by null HTTP is idle in state(s) 0 Telnet is idle in state(s) 0 File is idle in state(s) 0 USB is idle in state(s) 0 Aux is idle in state(s) 0 Trigger is idle in state(s) 0 Queue is idle in state(s) 0 LCD is idle in state(s) 0 SBC is idle in state(s) 0 Daemon is idle in state(s) 0 Aux2 is idle in state(s) 0 Autopause is idle in state(s) 0 Code queue is empty. === Filament sensors === Extruder 0 sensor: ok === CAN === Messages queued 6086, received 0, lost 0, longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 49 (min 48), ts 3388/0/0 Tx timeouts 0,5,3387,5,0,2685 last cancelled message type 4514 dest 127 === Network === Slowest loop: 50.62ms; fastest: 0.02ms Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions HTTP sessions: 1 of 8 - Ethernet - State: active Error counts: 0 0 0 0 0 Socket states: 5 2 2 2 2 0 0 0 -
-
@fcwilt
Thanks fcwilt. the error still persists with the capital S. -
@akayoshi said in Bed Levelling with independent Z motors error:
@fcwilt
Thanks fcwilt. the error still persists with the capital S.Well it was a long shot at best since nothing else jumped out.
Must be missing something. I'll take another look.
Frederick
-
Ah... there it is.
You have a second M671 at line 105 of the config file list which is specifying 4 lead screws.
Frederick
-
@fcwilt You sir are a scholar! Thank you.
