• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login

T0 Stopped working

Scheduled Pinned Locked Moved
General Discussion
3
13
1.3k
Loading More Posts
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • undefined
    mattbaker
    last edited by 24 Sept 2017, 13:54

    I've only had the board about 6 weeks. I bought it from Filastruder.

    1 Reply Last reply Reply Quote 0
    • undefined
      dc42 administrators
      last edited by 24 Sept 2017, 14:30

      Was that M122 report was done with the extruder connected to E1? if so, please do another one with the extruder connected to E0 and extruder mapped back to E0. The OK status suggests that the driver hasn't been commanded.

      Duet WiFi hardware designer and firmware engineer
      Please do not ask me for Duet support via PM or email, use the forum
      http://www.escher3d.com, https://miscsolutions.wordpress.com

      1 Reply Last reply Reply Quote 0
      • undefined
        mattbaker
        last edited by 24 Sept 2017, 14:47

        I had a stepper attached to the driver, and config setup was for two drives. I have run the m122, remapped and with a stepper attached to D0 and D1, the results were the same.

        1 Reply Last reply Reply Quote 0
        • undefined
          mattbaker
          last edited by 24 Sept 2017, 14:50

          Also, do you know a way from stopping the wifi dropping out. The printer is only about 15 feet from the router.

          1 Reply Last reply Reply Quote 0
          • undefined
            dc42 administrators
            last edited by 24 Sept 2017, 16:02

            Regarding the driver, please ask Filastruder to repair or replace the Duet under warranty.

            Regarding wifi dropping out, see https://duet3d.com/wiki/WiFi_disconnections_and_AJAX_timeout_errors.

            Duet WiFi hardware designer and firmware engineer
            Please do not ask me for Duet support via PM or email, use the forum
            http://www.escher3d.com, https://miscsolutions.wordpress.com

            1 Reply Last reply Reply Quote 0
            • undefined
              mattbaker
              last edited by 24 Sept 2017, 20:02

              Thanks for your help, I thought that must be the case.

              1 Reply Last reply Reply Quote 0
              • undefined
                mattbaker
                last edited by 25 Sept 2017, 00:10

                I must note a correction. It was more like 11 weeks from the time I received the board, and when I raised the issue with filastruder. With was by no means an attempt to mislead. Nor did I think I would benefit from the genuine mistake, as I thought it might be a config/firmware issue after seeking advice from filastruder.

                1 Reply Last reply Reply Quote 0
                • undefined
                  dc42 administrators
                  last edited by 25 Sept 2017, 07:07

                  No problem.

                  Duet WiFi hardware designer and firmware engineer
                  Please do not ask me for Duet support via PM or email, use the forum
                  http://www.escher3d.com, https://miscsolutions.wordpress.com

                  1 Reply Last reply Reply Quote 0
                  • undefined
                    mattbaker
                    last edited by 25 Sept 2017, 07:10

                    Hi dc42,

                    I have been advised buy Filastruder that I need to deal with you directly, as I live in Australia.

                    1 Reply Last reply Reply Quote 0
                    • undefined
                      Roland
                      last edited by 25 Sept 2017, 08:38

                      Hi Matt

                      Normally we would replace your Duet direct from the UK but won't be able to do so this week as we are at the TCT Show in Birmingham displaying our products. I will ask Filastruder to send you a replacement.

                      1 Reply Last reply Reply Quote 0
                      • undefined
                        mattbaker
                        last edited by 25 Sept 2017, 09:53

                        Thanks that would be awesome.

                        1 Reply Last reply Reply Quote 0
                        12 out of 13
                        • First post
                          12/13
                          Last post
                        Unless otherwise noted, all forum content is licensed under CC-BY-SA