I could use some help

[A Former User]

@mac

[fcwilt]

@mac said in I could use some help:

On the other side: (the red wheel is up on the left), the casing says NC (far left) NO (center), and O (right side).

That O is actually a C for COMMON. The NC is for NORMALLY CLOSED. The NO is for NORMALLY OPEN.

The GREEN WIRE is in the middle, it is connected to the NO post on this side, and it is numbered 3 on the other side.
The WHITE WIRE is on the RIGHT (below the end of the metal arm), it is labeled O on this side, and 1 on the other.

Which is perfectly consistent with how we had to set the M574 commands.
...

I really want to get your printer up and running so would you please find a way to measure the Y axis movement and verify that is moves the distance you command it to move.

We cannot move forward until we have verified the Y axis is moving as it should in regards to distance.

That likely will tell us what needs to be done to rectify homing problems with all of the axes.

Please.

Frederick

[A Former User]

@fcwilt I’ll turn everything on, and do that right now.

[A Former User]

@fcwilt 5 moves of Y+10 towards the front of the printer covered 46.8265mm.

[A Former User]

@fcwilt 5 moves of Y+10 covered 46.8265mm.

[A Former User]

@fcwilt so the accuracy is 93.65%?

[fcwilt]

@mac said in I could use some help:

@fcwilt so the accuracy is 93.65%?

That is rather strange. I expected a completely different outcome.

It should have moved very close to 50mm.

To compute the correct value in M92 for the Y stepper we just determine the ratio of the correct distance to the actual distance - 50.00 / 46.82 which is 1.0679.

The current value in M92 is 80? or was it 40?

In any case you take the current value and multiply by 1.0679.

80 x 1.0679 = 85.433

40 x 1.0679 = 42.716

But those values make no sense to me at all. Every printer I have built has had simple integer values in M92.

So take whatever the current M92 value for Y is and multiply by 1.0679 and use that new value in the M92.

Re-boot and re-test the Y movement and see if it comes out very close to 50.00.

I need to think about how these values might make sense.

Frederick

[A Former User]

@fcwilt I’ll do it right now.

[fcwilt]

@mac said in I could use some help:

@fcwilt I’ll do it right now.

That would be grand. I've got quite a bit of time at the moment to work with you.

Frederick

[A Former User]

@fcwilt well, here's the first problem, and I remember changing this to half of these numbers:

M92 X80.00 Y80.00 Z4000.00 E420.00

[fcwilt]

@mac said in I could use some help:

@fcwilt well, here's the first problem, and I remember changing this to half of these numbers:

M92 X80.00 Y80.00 Z4000.00 E420.00

All that matters is what they are now in the config.g file because those are the values that you have been using everything you have re-booted the printer.

If what is there now for Y now is 80 then just replace the 80 with 85.433, re-boot and re-test Y movement.

Thanks.

Frederick

[A Former User]

@fcwilt I'm been redoing the measurement to see if it's the same each time. I'm more comfortable with 1.5625 inches, which is 39.6875 mm.

50 divided by 39.6875 is 1.2598.
80 times 1.2598 is 100.784.

That sounds like 100 to me.

I think those are better numbers, don't you?

[fcwilt]

@mac said in I could use some help:

@fcwilt I'm been redoing the measurement to see if it's the same each time. I'm more comfortable with 1.5625 inches, which is 39.6875 mm.

50 divided by 39.6875 is 1.2598.
80 times 1.2598 is 100.784.

I think those are better numbers, don't you?

Now that is starting to make sense. 100 is a value that is common in "printer land".

So assuming X and Y use the same hardware setup (belts, pulleys, etc) then you should enter 100 for X and Y.

I bet that will work out just fine.

Especially once we find the issue that is causing the X stepper to malfunction. Any evidence yet to indicate an intermittent wiring problem?

Oh yes. After you have 100 in place for Y, at least, re-boot and try homing Y and see if it triggers the Y endstop twice and returns to the center of the bed.

I have my fingers crossed.

Frederick

[A Former User]

@fcwilt Okay, I'm going to change X and Y to 100.00 each. Save, reboot, and then Home Y.

[fcwilt]

@mac said in I could use some help:

@fcwilt Okay, I'm going to change X and Y to 100.00 each. Save, reboot, and then Home Y.

Fingers still crossed.

Frederick

[A Former User]

@fcwilt Okay, Y started out very slowly, and went towards HOME (the rear of the printer), but stopped 89mm from the end-stop.

I'm sorry, Frederick, it's just not happening.

[fcwilt]

@mac said in I could use some help:

@fcwilt Okay, Y started out very slowly, and went towards HOME (the rear of the printer), but stopped 89mm from the end-stop.

I'm sorry, Frederick, it's just not happening.

And yet jogging Y is now yielding correct distances?

Frederick

[A Former User]

@fcwilt The nozzle is 51mm west of the front of the bed (the back of the printer is pointed west).

[A Former User]

@fcwilt I haven't tried to find that out yet. I'll do that now.

[fcwilt]

@mac said in I could use some help:

@fcwilt The nozzle is 51mm west of the front of the bed (the back of the printer is pointed west).

OK back to my previous question.

With the new value of 100 are Y movements done via jogging moving the correct distances?

Frederick