Print status percent incorrect

shirnschall

Hi,
I recently noticed that the print status percent is extremely off for some prints and I am unsure what this percentage is based on. I tend to run a simulation before starting the print to get an accurate print time estimate (Although the slicer estimation is very close for my printer). I have attached screenshots of two different prints, both with the issue described above. I guess this statistic it is based on "File Progress" as it is very wrong for all other stats available (layers, filament usage, slicer estimate, and simulation). I am not sure if there is a better way for doing this.
I am using a duet 2 wifi with firmware version 3.4.0.

Phaedrux

Can you share an example gcode file?

Can you confirm that your DWC version matches your firmware version?

shirnschall

@phaedrux Hi,
yes I am using DWC 3.4.0 as well.
Please download the gcode from github as it was too large to upload here.

Here is the M122 output (just in case).

M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.4.0 (2022-03-15 18:58:31) running on Duet WiFi 1.02 or later + DueX5
Board ID: 08DGM-9T6BU-FG3SN-6JKDJ-3S86N-98ZHF
Used output buffers: 3 of 24 (24 max)
=== RTOS ===
Static ram: 23868
Dynamic ram: 76252 of which 24 recycled
Never used RAM 11792, free system stack 118 words
Tasks: NETWORK(ready,15.5%,232) HEAT(notifyWait,0.0%,332) Move(notifyWait,0.0%,305) DUEX(notifyWait,0.0%,24) MAIN(running,84.3%,466) IDLE(ready,0.2%,30), total 100.0%
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:10:23 ago, cause: software
Last software reset at 2022-07-24 00:59, reason: User, GCodes spinning, available RAM 8144, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x04
Step timer max interval 0
MCU temperature: min 39.4, current 41.8, max 42.1
Supply voltage: min 1.0, current 24.4, max 24.6, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: standstill, SG min 0
Driver 1: standstill, SG min 0
Driver 2: standstill, SG min 0
Driver 3: standstill, SG min n/a
Driver 4: standstill, SG min 0
Driver 5: standstill, SG min n/a
Driver 6: standstill, SG min n/a
Driver 7: standstill, SG min 0
Driver 8: standstill, SG min n/a
Driver 9: standstill, SG min 0
Driver 10: 
Driver 11: 
Date/time: 2022-07-24 01:10:14
Cache data hit count 4294967295
Slowest loop: 69.92ms; fastest: 0.11ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 1.9ms, write time 120.6ms, max retries 0
=== Move ===
DMs created 83, segments created 6, maxWait 81367ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 89, completed 89, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 59], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1, chamber heaters 2 -1 -1 -1, ordering errs 0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== DueX ===
Read count 1, 0.10 reads/min
=== Network ===
Slowest loop: 233.93ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 2 of 8
- WiFi -
Network state is active
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.26
WiFi MAC address 84:f3:eb:41:aa:d2
WiFi Vcc 3.42, reset reason Power up
WiFi flash size 4194304, free heap 23920
WiFi IP address 192.168.0.111
WiFi signal strength -57dBm, mode 802.11n, reconnections 0, sleep mode modem
Clock register 00002002
Socket states: 0 0 0 0 0 0 0 0

Phaedrux

Please update to 3.4.1

shirnschall

@phaedrux OK. Thank you

dc42

@shirnschall to expand on the response from @Phaedrux, the release notes for DWC 3.4.1 at https://github.com/Duet3D/DuetWebControl/wiki/Changelog-DWC-3.x include this bug fix:

Job progress did not use filament information if available

shirnschall

@dc42 Thank you for the clarification
I have already updated to the new version.