Duet 3 SD 0 card not recognised

[Togmore]

I have just purchased a Duet3 mini ethernet and i cant get it to recognise the SD card in slot 0
Sending M122 responds with" Card0 not detected" i have also replaced the cared from my working Duet 2 and receive the same response. Reading additional information on the posts it appears that this is a faulty card any help would be appreciated

[droftarts]

@togmore please can you post the full M122 response?

Ian

[Togmore]

Thank you Ian new to this so i hope this is what you need

@droftarts === Diagnostics ===
RepRapFirmware for Duet 3 Mini 5+ version 3.2.2 running on Duet 3 Mini5plus Ethernet (SBC mode)
Board ID: Q0MXM-2296U-D65J0-40KM2-LT03Z-HG85Q
Used output buffers: 1 of 40 (1 max)
=== RTOS ===
Static ram: 98732
Dynamic ram: 92788 of which 0 recycled
Never used RAM 53696, free system stack 152 words
Tasks: Linux(ready,423) HEAT(blocked,362) CanReceiv(blocked,947) CanSender(blocked,372) CanClock(blocked,362) TMC(blocked,123) MAIN(running,610) IDLE(ready,20) AIN(blocked,269)
Owned mutexes: USB(MAIN)
=== Platform ===
Last reset 00:00:22 ago, cause: power up
Last software reset details not available
Error status: 0x00
Aux0 errors 0,0,0
Aux1 errors 0,0,0
Supply voltage: min 0.0, current 0.9, max 0.9, under voltage events: 0, over voltage events: 0, power good: no
Driver 0: position 0, ok, SG min/max not available, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0
Driver 1: position 0, ok, SG min/max not available, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0
Driver 2: position 0, ok, SG min/max not available, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0
Driver 3: position 0, ok, SG min/max not available, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0
Driver 4: position 0, ok, SG min/max not available, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0
Driver 5: position 0, ok, SG min/max not available, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0
Driver 6: position 0, ok, SG min/max not available, read errors 0, write errors 0, ifcnt 0, reads 0, writes 0, timeouts 0, DMA errors 0
Date/time: 1970-01-01 00:00:00
Cache data hit count 58519423
Slowest loop: 0.21ms; fastest: 0.00ms
=== Storage ===
Free file entries: 10
SD card 0 not detected, interface speed: 0.0MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is ready with "M122" in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== CAN ===
Messages queued 113, send timeouts 112, received 0, lost 0, longest wait 0ms for reply type 0, free buffers 16
=== SBC interface ===
State: 0, failed transfers: 0
Last transfer: 22510ms ago
RX/TX seq numbers: 0/1
SPI underruns 0, overruns 0
Number of disconnects: 0, IAP RAM available 0x113e0
Buffer RX/TX: 0/0-0
ok

[droftarts]

@togmore the interface speed means that the SD socket is disconnected:

SD card 0 not detected, interface speed: 0.0MBytes/sec

It should be replaced under warranty. Where and when did you purchase it? Also, can you take a picture of the area around the SD card socket?

Ian

[Togmore]

@droftarts I Ian purchased from Ooznest Tuesday delivered Wednesday picture attached
Steve

[droftarts]

@togmore I can’t see anything particularly wrong with the soldering, but it’s clearly not working.

Please send an email to warranty@duet3d.com and CC your reseller. Include a link to this forum thread and the details of your original purchase. You'll receive a reply with a form to fill out.

Sorry for the inconvenience.

Ian

[Phaedrux]

@togmore said in Duet 3 SD 0 card not recognised:

Duet 3 Mini5plus Ethernet (SBC mode)

Can you confirm that it's not actually connected to a raspberry Pi?