PID Tuning Part Fan Not Turning On
-
Hi All,
Thanks in advance for the help! I'm trying to run the PID tuner for my extruder and I can't map the part fan to it. I've tried a couple options and haven't been able to find the answer.
The part fan is plugged into PWM Fan 0, below is my config.g.
When I try "M303 H1 S230" the extruder heats up as expected but the fan does not turn on. The fan works normal otherwise.
; Configuration file for Duet WiFi (firmware version 3.3) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v3.3.10 on Thu Feb 24 2022 18:43:24 GMT-0800 (Pacific Standard Time) ; General preferences M575 P1 S1 B57600 ; enable support for PanelDue G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"Zender" ; set printer name ; Network M552 S1 ; enable network M586 P0 S1 ; enable HTTP M586 P1 S0 ; disable FTP M586 P2 S0 ; disable Telnet ; Drives M569 P0 S1 ; physical drive 0 goes forwards M569 P1 S1 ; physical drive 1 goes forwards M569 P2 S1 ; physical drive 2 goes forwards M569 P3 S1 ; physical drive 3 goes forwards M584 X0 Y1 Z2 E3 ; set drive mapping M350 X128 Y128 Z128 E128 I0 ; configure microstepping without interpolation, was 128 M92 X700.55 Y700.55 Z3103.00 E1271 ; set steps per mm, was 200 M566 X6000.00 Y6000.00 Z600.00 E3000.00 ; set maximum instantaneous speed changes (mm/min) was 300 M203 X18000.00 Y18000.00 Z300.00 E1200.00 ; set maximum speeds (mm/min) e was 1200 M201 X500.00 Y500.00 Z20.00 E3000.00 ; set accelerations (mm/s^2) was 20 M906 X1500 Y1500 Z1200 E650 I30 ; set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout was 800 ; Axis Limits M208 X0 Y0 Z0 S1 ; set axis minima M208 X200 Y210 Z300 S0 ; set axis maxima ; Endstops M574 X1 S1 P"xstop" ; configure switch-type (e.g. microswitch) endstop for low end on X via pin xstop M574 Y2 S1 P"ystop" ; configure switch-type (e.g. microswitch) endstop for high end on Y via pin ystop M574 Z1 S2 ;configure Z-probe endstop for low end on Z ; Z-Probe M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch M558 P9 C"^zprobe.in" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds G31 P500 X0 Y30 Z1.15 ; set Z probe trigger value, offset and trigger height Z was 1.98 M557 X15:190 Y15:195 S40 ; define mesh grid ; Heaters M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0 M307 H1 B0 R2.384 C182.2 D4.43 S1.00 V12.2 ; disable bang-bang mode for the bed heater and set PWM limit, was M307 H0 B0 M140 H0 ; map heated bed to heater 0 M143 H0 S120 ; set temperature limit for heater 0 to 120C M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1 M307 H1 B0 R2.149 C134.4 D5.40 S1.00 V12.2 ; disable bang-bang mode for heater and set PWM limit, was M307 H1 B0 R2.565 C160.0 D4.58 S1.00 V12.2 M143 H1 S280 ; set temperature limit for heater 1 to 280C ; Fans M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency "Part cooling fan" M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned on at 45C M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency "extruder cooling fan" M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned off ; Tools M563 P0 D0 H1 F0 ; define tool 0, F was -1 now 0 G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C ; Custom settings are not definedThanks again!
-
@jdzender said in PID Tuning Part Fan Not Turning On:
M303 H1 S230
To get the fan to be part of the tuning process you must tune it as a tool using
M303 T0 S230instead.
