Failed to get file list - Service Unavailable
-
Hi!
Upgraded my Duet 2 WiFi from a older 3.4 beta to latest and greatest today.
After uploading a file, be it in DWC or trough PrusaSlicer, it doesn't show up in the job list and when refreshing I get the error:
Not sure if it's DWC or where this comes from. After waiting a while, refreshing works again.
=== Diagnostics === RepRapFirmware for Duet 2 WiFi/Ethernet version 3.5.2 (2024-06-11 17:13:43) running on Duet WiFi 1.02 or later + DueX5 Board ID: 08DGM-956GU-DJMSN-6J1FJ-3SN6T-KTNHD Used output buffers: 16 of 26 (26 max) === RTOS === Static ram: 23384 Dynamic ram: 74276 of which 0 recycled Never used RAM 12364, free system stack 120 words Tasks: NETWORK(2,nWait 6,14.3%,195) HEAT(3,nWait 5,0.1%,319) Move(4,nWait 5,0.3%,298) DUEX(5,nWait 5,0.0%,23) MAIN(1,running,85.2%,717) IDLE(0,ready,0.1%,29), total 100.0% Owned mutexes: WiFi(NETWORK) === Platform === Last reset 02:11:20 ago, cause: software Last software reset at 2024-08-26 16:49, reason: User, Gcodes spinning, available RAM 11684, slot 1 Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a Error status: 0x14 MCU temperature: min 38.3, current 39.1, max 42.4 Supply voltage: min 23.9, current 24.3, max 24.6, under voltage events: 0, over voltage events: 0, power good: yes Heap OK, handles allocated/used 99/0, heap memory allocated/used/recyclable 2048/96/96, gc cycles 0 Events: 0 queued, 0 completed Driver 0: standstill, SG min 153 Driver 1: standstill, SG min 0 Driver 2: standstill, SG min 0 Driver 3: standstill, SG min n/a Driver 4: standstill, SG min 0 Driver 5: standstill, SG min 0 Driver 6: standstill, SG min 185 Driver 7: standstill, SG min n/a Driver 8: standstill, SG min 0 Driver 9: standstill, SG min 0 Driver 10: Driver 11: Date/time: 2024-08-26 19:00:51 Cache data hit count 4294967295 Slowest loop: 267.71ms; fastest: 0.17ms I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0 === Storage === Free file entries: 9 SD card 0 detected, interface speed: 20.0MBytes/sec SD card longest read time 12.2ms, write time 228.7ms, max retries 0 === Move === DMs created 83, segments created 11, maxWait 842538ms, bed compensation in use: mesh, height map offset 0.000, max steps late 0, min interval 0, bad calcs 0, ebfmin 0.00, ebfmax 1.00 no step interrupt scheduled Moves shaped first try 0, on retry 0, too short 0, wrong shape 0, maybepossible 0 === DDARing 0 === Scheduled moves 9696, completed 9696, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1 === Heat === Bed heaters 0 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0 Heater 0 is on, I-accum = 0.2 Heater 1 is on, I-accum = 0.3 === GCodes === Movement locks held by null HTTP is idle in state(s) 0 Telnet is idle in state(s) 0 File is idle in state(s) 0 USB is idle in state(s) 0 Aux is idle in state(s) 0 Trigger is idle in state(s) 0 Queue is idle in state(s) 0 LCD is idle in state(s) 0 Daemon is idle in state(s) 0 Autopause is idle in state(s) 0 Q0 segments left 0 Code queue 0 is empty === Filament sensors === check 2921242 clear 26867682 Extruder 0 sensor: no filament === DueX === Read count 0, 0.00 reads/min === Network === Slowest loop: 247.23ms; fastest: 0.07ms Responder states: HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) HTTP sessions: 1 of 8 === WiFi === Interface state: active Module is connected to access point Failed messages: pending 0, notrdy 0, noresp 0 Firmware version 2.1.0 MAC address 5c:cf:7f:76:66:58 Module reset reason: Turned on by main processor, Vcc 3.40, flash size 4194304, free heap 39528 WiFi IP address 192.168.1.205 Signal strength -55dBm, channel 8, mode 802.11n, reconnections 0 Clock register 00002002 Socket states: 0 0 0 0 0 0 0 0Regards, Andrei
-
@TypQxQ that's a long write time on the SD card. I would suggest refreshing the SD card (don't forget to back everything up) or replace the SD card for a newer one
