• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login

Duet3 6HC and TOOL1RR Heightmap

Scheduled Pinned Locked Moved
Duet Hardware and wiring
2
6
142
Loading More Posts
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • undefined
    jhanda
    last edited by 29 Dec 2024, 19:20

    I just swapped my toolhead for the Roto with the Duet Roto toolboard. I have. a BL Touch for main z probe and the SZP. When I run the SZP heightmap I always get the error "Warning: the height map has a substantial Z offset. Suggest use Z-probe to establish Z=0 datum, then re-probe the mesh." It seems like the whole map iss offset by about -.3mm or so. I set Z using the BLtouch and calibrated the SZP at z=2. Any ideas? I'm stuck.

    undefined undefined 2 Replies Last reply 29 Dec 2024, 19:21 Reply Quote 0
    • undefined
      jhanda @jhanda
      last edited by 29 Dec 2024, 19:21

      heres my mesh.g

      M557 X30:260 Y35:250 P20 ; Define grid for mesh bed compensation,
      G29 S2 ; Disable mesh bed compensation
      G28 Z ; Home Z
      G1 Z6 ; To avoid backlash move to point higher than start of calibration
      M558.1 K1 S1.3 ; Calibrate probe
      G1 Z6 ; Move up at end of calibration
      G29 S0 K1 ; Scan bed and create mesh
      undefined 1 Reply Last reply 29 Dec 2024, 19:23 Reply Quote 0
      • undefined
        jhanda @jhanda
        last edited by 29 Dec 2024, 19:23

        config.g

        ;M111 S0 ; Debug off
        ;M555 P2 ; Set output to look like Marlin
        M950 P9 C"out1" ; Create Tool Board output
        M42 P9 S1 ; Turn on Tool Board
        G4 S2 ; wait for expansion boards to start
        G21 ; Work in millimetres
        G90 ; Send absolute coordinates...
        M83 ; ...but relative extruder moves
        ; Axis and motor configuration
        M669 K1 ; CoreXY mode
        M569 P0.0 S0 ; Drive 0 goes forwards Z (Left Front)
        M569 P0.1 S0 ; Drive 1 goes backward Z (Right)
        M569 P0.2 S0 ; Drive 2 goes forwards Z (Left Rear)
        M569 P0.3 S1 ; Drive 3 goes forwards Y
        M569 P0.4 S0 ; Drive 4 goes forwards X
        M569 P0.5 S1 ; Drive 5 goes forwards Unused
        ;M569 P20.0 S1 ; etruder
        ;M584 X4 Y3 Z2:0:1 E20.0 ; Drive Mapping
        M584 X4 Y3 Z2:0:1 E5 ; Drive Mapping
        M350 X16 Y16 Z16 E16 I1 ; 16x microstepping with interpolation
        M92 X200.00 Y200.00 Z1600.00 E393 ; Set steps/mm
        M566 X1600 Y1600 Z200 E1500 ; Set maximum jerk
        M203 X6000 Y6000 Z900 E3600 ; Set maximum speeds (mm/min)
        M201 X1750 Y1750 Z250 E1500 ; Set maximum acceleration (mm/s^2)
        M906 X1200 Y1200 Z800 E1000 I30 ; Set motor currents (mA)
        M84 S30
        ;Leadscrew locations
        M671 X-23.6:-23.6:343.6 Y-3.5:251.2:124.4 S7.5 ;
        ; Axis Limits
        M208 X0 Y0 Z-0.5 S1 ; Set axis minima
        M208 X270 Y250 Z250 ; Set axis maxima
        ; Endstops
        M574 X2 S1 P"io0.in" ; Configure active-high endstop for high end on X via pin io0.in
        M574 Y1 S1 P"io1.in" ; Configure active-high endstop for low end on Y via pin io1.in
        ; Z-Probe
        M950 S2 C"21.io0.out" ; Create servo pin on toolboard pin 0 for BLTouch
        M558 P9 C"21.io0.in" H8 F100 T2000 ; Set Z probe type to bltouch and the dive height + speeds
        M280 P2 S160 ; Release alarms and retract pin.
        ;G31 X0 Y20 Z2.286 P25 ; Set Z probe trigger value, offset and trigger height 3.63 E3d .4 3.67 Slice .4 3.118 Micro, 3.980 Mosquito
        G31 X28.8 Y24.3 Z2.044 P25 ; Set Z probe trigger value, offset and trigger height Revo Roto
        ;M557 X40:280 Y21:241 S20 ; define mesh grid
        ; Scanning Z probe
        M558 K1 P11 C"21.i2c.ldc1612" F36000 T36000
        M308 A"SZP coil" S10 Y"thermistor" P"21.temp2" ; thermistor on coil
        G31 K1 Z2 X26 Y9
        M558.2 K1 S16 R134318
        M955 P21.0 I16 ; Add accelerometer on Roto with CAN address 21 and specify orientation
        ; Heaters
        M308 S0 P"temp0" Y"thermistor" A"Bed" T100000 B4725 C7.06e-8; Configure sensor 0 as thermistor on pin temp0
        M950 H0 C"pson" T0 Q10 ; Create bed heater output on pson and map to sensor 0
        M143 H0 S120 ; Set temperature limit for heater 0 to 120C
        ;M307 H0 A77.6 C278.8 D11.9 V24.1 B0 ; Bed Heater PID Calibration
        M307 H0 R0.296 C345.2 D21.13 S1.00 ; Bed Heater PID Calibration
        M140 H0 ; Map heated bed to heater 0
        ;M308 S1 P"20.temp0" Y"thermistor" A"Hotend" T100000 B4725 C7.06e-8; Configure sensor 1 as thermistor on pin temp1
        M308 S1 P"temp2" Y"thermistor" A"Hotend" T500000 B4723 C1.196220e-7; Configure sensor 1 as thermistor on pin temp2 (Slice Engineering)
        ;M950 H1 C"20.out0" T1 ; Create nozzle heater on toolboard out1, map it to sensor 1
        M950 H1 C"out2" T1 ; Create nozzle heater on toolboard out1, map it to sensor 1
        ;M143 H1 S290 ; Set temperature limit for heater 1 to 280C
        M143 H1 S350 ; Set temperature limit for heater 1 to 350C Mosquito
        ;M307 H1 B0 S1.00 ; Disable bang-bang mode for heater and set PWM limit
        ;M307 H1 R2.423 C242.8:143.5 D7.43 S1.00 V24.1
        M307 H1 R2.436 C166.7 D7.27 S1.00 V24.1
        ; Fans
        M950 F0 C"out8" Q500 ; Create fan 0 on toolboard and set its frequency (Layer)
        M106 P0 C"Part Cooling" S0 H-1 ; Set fan 0 value. Thermostatic control is turned off
        M950 F1 C"out9" Q500 ; Create fan 1 on toolboard and set its frequency (Mosquito)
        ;M950 F1 C"20.out1" Q500 ; Create fan 1 on toolboard and set its frequency (Hemera)
        M106 P1 S1 H1 T45 ; Set fan 1 value. Thermostatic control is turned on
        ; Tools
        ;M563 P0 S"Hemera" D0 F1 H1 ; Define tool 0
        ;M563 P0 S"Mosquito" D0 F1 H1 ; Define tool 0
        M563 P0 S"Revo" D0 F1 H1 ; Define tool 0
        G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
        G10 P0 S0 R0 ; Set initial tool 0 active and standby temperatures to 0C
        ;M572 D0 S0.06 ; .06 Pressure advance Amazon Basics PETG
        ;M207 S0.4 F3600 R0.2 T2400 Z0.18 ; Retractions this one worked
        ;M207 S0.7 F3600 R0 T3600 Z0.18
        ; Miscellaneous
        T0 ; select first tool
        undefined 1 Reply Last reply 29 Dec 2024, 19:24 Reply Quote 0
        • undefined
          jhanda @jhanda
          last edited by 29 Dec 2024, 19:24

          bed.g

          M561 ; clear any existing bed transform
          G1 Z5 ; _RRF3_ remove S2
          G30 P0 X35 Y45 Z-99999
          G30 P1 X35 Y250 Z-99999
          G30 P2 X270 Y250 Z-99999
          G30 P3 X270 Y45 Z-99999 S3
          G1 X0 Y0 F5000 ; move the head to the corner (optional)
          undefined 1 Reply Last reply 29 Dec 2024, 19:26 Reply Quote 0
          • undefined
            jhanda @jhanda
            last edited by 29 Dec 2024, 19:26

            homez.g

            G91
            G1 Z5 F800 H2 ;_RRF3_ change S2 to H2
            G90
            ;G1 X104.5 Y79.5 F2400
            ;G1 X64.2 Y90.7 F2400
            G1 X66.3 Y91.6 F2400
            G30
            G29 S1
            G1 Z2 F200
            1 Reply Last reply Reply Quote 0
            • undefined
              droftarts administrators @jhanda
              last edited by 31 Dec 2024, 13:49

              @jhanda I’m on my phone, so it’s difficult to spot errors in your config and macros. I can have a better look in the New Year. However, generally, it sounds like the Z offset of the BLTouch and the SZP are referencing the same Z0. You’re not the first to struggle with this, and I’m going to review the SZP instructions in the New Year: https://docs.duet3d.com/en/User_manual/Tuning/scanning_z_probe_calibration

              Initially, you need to set Z0 with the BLTouch (assuming this sets the nozzle height correctly), then use this to calibrate the SZP Z offset. Note that:

              • make sure that no heightmap is applied when homing Z with the BLTouch or calibrating the SZP. Add M561 and/or G29 S2 before the SZP calibration to make sure any mesh is disabled.
              • SZP calibration changes with temperature. You will need to recalibrate it before scanning if the temperature changes. As you have a BLTouch, you can do this in a macro, and can be done before every scan.

              Ian

              Bed-slinger - Mini5+ WiFi/1LC | RRP Fisher v1 - D2 WiFi | Polargraph - D2 WiFi | TronXY X5S - 6HC/Roto | CNC router - 6HC | Tractus3D T1250 - D2 Eth

              1 Reply Last reply Reply Quote 0
              3 out of 6
              • First post
                3/6
                Last post
              Unless otherwise noted, all forum content is licensed under CC-BY-SA