One-press resume printing after power failure

Phaedrux

@resam well you don't have to move the bed at all really. If it hasn't dropped at all you can simply modify that macro before you print the resurrect file and change the G92 Z value to be the final z height from the time of power loss. You'd still have to dig it out yourself though.

resam

Yes - thats what I'm complaining about
I don't want to go digging around to find the Z value.

It would be nice to at least put it at the top of the file in a nice comment.

Even better would be some sort of integration / M291 magic - but this might be highly specific to each printer type, so I'm not putting my hopes up.

wilriker

@resam said in One-press resume printing after power failure:

I would propose to at least add a comment at the top of the file:
; Z height before power was lost: 12.5mm
; Z height after running the "auto save on loss of power" g-codes: 15.5mm

From what I can see in the source code at least the first line should be fairly easy to add.
I would be a little bit concerned with the second one as this is the height of Z if and only if there was enough power left to move Z - and this could even be only a partial movement.

Here we come to a point of uncertainty on my side as the code here is rather complex: AFAICT the file is written before running the M911 P part so at this time it is unknown whether this will succeed or not - and at the time it is known the file is closed and probably not enough power left to append this info either.
This might be confirmed by @dc42.

resam

Yes there is uncertainty - thats why I think adding both values would be good.
The user should check & verify the current Z height against these two values before proceeding.
I guess I could deduct the second value myself by looking at my M911 command list... but this would be yet another file to check...

wilriker

@resam said in One-press resume printing after power failure:

The user should check & verify the current Z height against these two values before proceeding.

But how do you reliably check whether Z has moved 2mm away or only 1.92mm - or any value in between. The nozzle of my printer is surrounded by stuff, so I would have no chance to get anything between the nozzle and the print to accurately measure this distance. Of course ball-park-numbers of full mm should be doable but finer then this... I don't see a chance.

What could be done with the first value (but that would still be extra manual work) would be to move the nozzle back manually onto the print (at best before heating up to not damage the print) and then set Z height based on what's in the comment. But at least the comment would help in that case.

I just had another look at the source code. The Z height is already in the file. It should be the third to last command

G0 F6000 Znnn <---
G1 Fnnn
M24

where nnn denotes the Z height at pausing.

dc42

I think the long-term solution will come when we support variables and parameters in GCode commands. Then we will be able to pass the Z height at which the print stopped to resurrect-prologue.g, and it can be used in a G92 command in that file.

dc42

Firmware 2.01 beta 2 puts a G92 command in resurrect.g, just before it calls resurrect-prologue.g.

resam

This is a step in the right direction!

As you clearly stated, this does not account for any Z movement in the command string when the print is stopped with M911.

Thinking about it some more, this means that people who can't home Z with a print on the bed should NOT perform any Z movement in the command string when the print is stopped with M911, because the G92 will not account for it, and you will end up 3mm too low (inside you print).

Since this would leave a hot hotend directly over your print, causing it to warp/melt, adding a Z-hop would still be beneficial.

@dc42 how about adding a new parameter to M911 that controls when and which G92 commands to insert. Something like:
M911 S19.8 R22.0 T0:0:2 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000"

With Tx:y:z being a single digit for each axis:

0: do not use G92 for this axis (there must be a G28 in resurrect-prologue.g for this axis!)
1: run G92for this axis with the last saved position before calling resurrect-prologue.g
2: run G92for this axis with the last saved position after calling resurrect-prologue.g

For my CoreXY machine, I would use T0:0:2, because I can home X and Y in the resurrect-prologue.g, but afterwards, I want to use G92 to set my Z height.
This allows people to not home at all, as well as doing a "partial" home for some axis.
Maybe this also helps people with absolute extruder coordinates, I'm not sure how this is currently handled?

Does this make sense, or am I missing anything?

wilriker

@resam I think you have a small mistake in your description of what "2" means because it is identical to what "1" means. I guess that 2 would mean setting G92 after resurrect-prologue.g, wouldn't it?

resam

@wilriker thanks - copy-paste error

dc42

@resam said in One-press resume printing after power failure:

This is a step in the right direction!

As you clearly stated, this does not account for any Z movement in the command string when the print is stopped with M911.

Thinking about it some more, this means that people who can't home Z with a print on the bed should NOT perform any Z movement in the command string when the print is stopped with M911, because the G92 will not account for it, and you will end up 3mm too low (inside you print).

Since this would leave a hot hotend directly over your print, causing it to warp/melt, adding a Z-hop would still be beneficial.

@dc42 how about adding a new parameter to M911 that controls when and which G92 commands to insert. Something like:
M911 S19.8 R22.0 T0:0:2 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000"

With Tx:y:z being a single digit for each axis:

0: do not use G92 for this axis (there must be a G28 in resurrect-prologue.g for this axis!)

1: run G92for this axis with the last saved position before calling resurrect-prologue.g

2: run G92for this axis with the last saved position after calling resurrect-prologue.g

For my CoreXY machine, I would use T0:0:2, because I can home X and Y in the resurrect-prologue.g, but afterwards, I want to use G92 to set my Z height.
This allows people to not home at all, as well as doing a "partial" home for some axis.
Maybe this also helps people with absolute extruder coordinates, I'm not sure how this is currently handled?

Does this make sense, or am I missing anything?

There is no guarantee that the Z hop in your power fail script will be completed, because the power reserve might run out first.

resam

@dc42 said in One-press resume printing after power failure:

There is no guarantee that the Z hop in your power fail script will be completed, because the power reserve might run out first.

Yes - I'm fully aware of that. But I feel like taking a risk today