Bltouch help
-
Hello,
back from vacation, I just set up the new bltouch. It works perfectly!I still have a problem, why and how to optimize the flatness of my bed?
-
What is your printing surface and bed construction?
-
it's glass
-
That height map would indicate a possible mechanical problem. Perhaps something is misaligned or bent.
How fast are you probing?
-
No, I do not think I have a mechanical problem.
Look at this bug when I run "auto delta calibration" I have this result.
But when I do "run mesh grid compensation", j'ai ce résultat.
This error message G29
D'ou vient le problème?
-
What are you using for your deployprobe.g and retractprobe.g macros?
-
; deployprobe.g
; called to deploy a physical Z probe
;
; generated by RepRapFirmware Configuration Tool on Thu Aug 02 2018 09:35:23 GMT+0200 (CEST)
;M280 P3 S160 I1
M280 P3 S10 I1; retractprobe.g
; called to retract a physical Z probe
;
; generated by RepRapFirmware Configuration Tool on Thu Aug 02 2018 09:35:23 GMT+0200 (CEST)
M280 P3 S90 I1 -
@rafb and how are you deploying and retracting in your bed.g? Are you manually calling it in your homing files or letting g30 handle it?
-
Are you manually calling it in your homing files or letting g30 handle it?
I do not know and do not understand; bed.g
; called to perform automatic delta calibration via G32
;
; generated by RepRapFirmware Configuration Tool on Thu Aug 02 2018 09:35:23 GMT+0200 (CEST)
M561 ; clear any bed transform
G28 ; home all towers
M190 S60
;M98 Pdeployprobe.g; déployer sonde mécanique de Z
; Probe the bed at 6 peripheral and 6 halfway points, and perform 6-factor auto compensation
; Before running this, you should have set up your Z-probe trigger height to suit your build, in the G31 command in config.g.
G30 P0 X0 Y132.28 H0 Z-99999
G30 P1 X121 Y69.86 H0 Z-99999
G30 P2 X129.9 Y-75 H0 Z-99999
G30 P3 X0 Y-150 H0 Z-99999
G30 P4 X-129.9 Y-75 H0 Z-99999
G30 P5 X-121 Y69.86 H0 Z-99999
G30 P6 X0 Y59.15 H0 Z-99999
G30 P7 X56.09 Y32.38 H0 Z-99999
G30 P8 X64.95 Y-37.5 H0 Z-99999
G30 P9 X0 Y-75 H0 Z-99999
G30 P10 X-64.95 Y-37.5 H0 Z-99999
G30 P11 X-56.09 Y32.38 H0 Z-99999
G30 P12 X0 Y0 H0 Z-99999 S6
; Use S-1 for measurements only, without calculations. Use S4 for endstop heights and Z-height only. Use S6 for full 6 factors
; If your Z probe has significantly different trigger heights depending on XY position, adjust the H parameters in the G30 commands accordingly. The value of each H parameter should be (trigger height at that XY position) - (trigger height at centre of bed)
;M98 Pretractprobe.g; rétracter la sonde mécanique Z
G29; homedelta.g
; called to home all towers on a delta printer
;
; generated by RepRapFirmware Configuration Tool on Thu Aug 02 2018 09:35:23 GMT+0200 (CEST)
G91 ; relative positioning
G1 S1 X705 Y705 Z705 F3600 ; move all towers to the high end stopping at the endstops (first pass)
G1 X-5 Y-5 Z-5 F3600 S2 ; go down a few mm
G1 S1 X10 Y10 Z10 F360 ; move all towers up once more (second pass)
G1 Z-5 F6000 ; move down a few mm so that the nozzle can be centred
G90 ; absolute positioning
G1 X0 Y0 F6000 ; move X+Y to the centre -
I do not find why I have this problem. I will start from scratch.
this bltouch seems not to be the best sensor for Duet
-
How do you have it wired?
Does it light up at all?
Can you send the servo commands to deploy and retract it?
-
the bltouch works great.
@rafb said in Bltouch help:
; deployprobe.g
; appelé à déployer une sonde de Z physique
;
; généré par l' outil de configuration RepRapFirmware le 02 août 2018 09:35:23 Jeu GMT + 0200 (CEST)
; M280 P3 S160 I1
M280 P3 S10 I1
; retractprobe.g
; appelé à se rétracter d' une sonde de Z physique
;
; généré par l' outil de configuration RepRapFirmware le 02 août 2018 09:35:23 Jeu GMT + 0200 (CEST)
M280 P3 S90 I1
