hell of a bed or I missed a config step

[Martin S]

Hey Guys...
maybe you can give me a good hint on how to improve my bed situation....


[Martin S]

config:

; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2 on Sun Dec 23 2018 12:24:41 GMT+0100 (Mitteleuropäische Zeit)

; General preferences
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves
M665 R125 L333 B115 H270 ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0 ; Put your endstop adjustments here, or let auto calibration find them

; Network
M550 P"Kossel XL" ; Set machine name
M551 P"xxxxx": ; Set password
M552 P0.0.0.0 S1 ; Enable network and acquire dynamic address via DHCP
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet

; Drives
M569 P0 S1 ; Drive 0 goes forwards
M569 P1 S1 ; Drive 1 goes forwards
M569 P2 S1 ; Drive 2 goes forwards
M569 P3 S1 ; Drive 3 goes forwards
M350 X32 Y32 Z32 I0 ; Configure microstepping without interpolation
M350 E16 I1 ; Configure microstepping with interpolation
M92 X200.00 Y200.00 Z200.00 E663.00 ; Set steps per mm
M566 X1200.00 Y1200.00 Z1200.00 E1200.00 ; Set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z18000.00 E1200.00 ; Set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z1000.00 E1000.00 ; Set accelerations (mm/s^2)
M906 X1000.00 Y1000.00 Z1000.00 E800.00 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 Z0 S1 ; Set minimum Z

; Endstops
M574 X2 Y2 Z2 S1 ; Set active high endstops

; Z-Probe

M307 H3 A-1 C-1 D-1 ; Disable heater on PWM channel for BL Touch
M558 P9 H15 F2400 T1200 ; Set Z probe type to bltouch and the dive height + speeds
G31 P50 X-27 Y-10 Z0 ; Set Z probe trigger value, offset and trigger height
M557 R115 S20 ; Define mesh grid

; Heaters
M305 P0 T100000 B4138 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S120 ; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4138 R4700 ; Set thermistor + ADC parameters for heater 1
M143 H1 S280 ; Set temperature limit for heater 1 to 280C

; Fans
M106 P0 S0.3 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

; Automatic saving after power loss is not enabled

; Custom settings are not configured

[Phaedrux]

@martin-s said in hell of a bed or I missed a config step:

M558 P9 H15 F2400 T1200 ; Set Z probe type to bltouch and the dive height + speeds
G31 P50 X-27 Y-10 Z0 ; Set Z probe trigger value, offset and trigger height

You are probing way too fast for a BLTouch. Try F100 instead. You also don't have a Z trigger height set in your G31. That will need to be measured using: https://duet3d.dozuki.com/Wiki/Test_and_calibrate_the_Z_probe#Section_Calibrate_the_Z_probe_trigger_height

[dc42]

It looks to me that you haven't run delta calibration, or if you did then you didn't save the results. See https://duet3d.dozuki.com/Wiki/Calibrating_a_delta_printer.