one Z stepper getting very hot, other fine?
-
@veti said in one Z stepper getting very hot, other fine?:
@alanknight said in one Z stepper getting very hot, other fine?:
M584 X0 Y1 Z2:3 E4.5
E4.5 is wrong you want E4:5
my bad, I read that wrong, M584 is for z axis only, fixed it, I'll let it cool and set it printing again
thanks guys
-
printing now again... it's hot as hell again
-
Does anything show in M122?
I see you're running a pretty old firmware version. I don't think there were any bugs like this, but you never know. You could try upgrading to 2.02 and seeing if it makes any difference.
Just to clarify, you fixed the error Veti pointed out, does M906 and M913 report both Z motors now? Just want to verify that your extruder is the one getting 1600 and not the second Z motor.
-
M112 runs an emergency stop?
M913
Motor current % of normal - X:100, Y:100, Z:100, E: 100:100M906
Motor current (mA) - X:600, Y:600, Z:750, E:1600:1600, idle factor 30%are my extruder and Z axis somehow mixed up? the printer prints fine, just that one z motor getting hot
(I added a space after E: to avoid the smilie)
-
M112 is emergency stop.
M122 is diagnostic report.
Painfully close, I know.
-
sorry my bad
M122
=== Diagnostics ===
Used output buffers: 3 of 32 (11 max)
=== Platform ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 1.21 running on Duet WiFi 1.02 or later
Board ID: 08DGM-956GU-DJMSN-6J9F4-3SD6Q-1VRRG
Static ram used: 16152
Dynamic ram used: 100408
Recycled dynamic ram: 2224
Stack ram used: 1224 current, 4512 maximum
Never used ram: 7776
Last reset 00:14:34 ago, cause: software
Last software reset at 2019-05-02 22:53, reason: User, spinning module GCodes, available RAM 7776 bytes (slot 0)
Software reset code 0x0003 HFSR 0x00000000, CFSR 0x00000000, ICSR 0x0441f000, BFAR 0xe000ed38, SP 0xffffffff
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms
MCU temperature: min 34.5, current 35.7, max 35.9
Supply voltage: min 12.3, current 12.7, max 13.1, under voltage events: 0, over voltage events: 0
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2019-05-02 23:08:15
Slowest main loop (seconds): 0.014124; fastest: 0.000046
=== Move ===
MaxReps: 0, StepErrors: 0, LaErrors: 0, FreeDm: 240, MinFreeDm 240, MaxWait: 0ms, Underruns: 0, 0
Scheduled moves: 0, completed moves: 0
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
Heater 0 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Responder states: HTTP(1) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8- WiFi -
Network state is running
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.21RC4(08b3)
WiFi MAC address 5c:cf:7f:76:61:21
WiFi Vcc 3.31, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 17336
WiFi IP address 192.168.1.239
WiFi signal strength -50dBm, reconnections 0, sleep mode modem
Socket states: 2 0 0 0 0 0 0 0
=== Expansion ===
should I updates? - do I lose my settings if I do?
it used to print fine... so I'm assuming I accidentally broke something, but I'm lost
- WiFi -
-
updated
Firmware Name: RepRapFirmware for Duet 2 WiFi/Ethernet
Firmware Electronics: Duet WiFi 1.02 or later
Firmware Version: 2.02(RTOS) (2018-12-24b1)
WiFi Server Version: 1.22
Web Interface Version: 1.22.6I've added a fan to that stepper for tonight, printer is at work, it's 11.30pm, i need to go home! butr also need some things printing asap so I'll leave it going with then fan
I'll check back tomorrow, thanks for the help
Alan
EDIT: ran these again before I go
11:28:37 PMM906
Motor current (mA) - X:600, Y:600, Z:750, E:1600:0, idle factor 30%
11:28:30 PMM913
Motor current % of normal - X:100, Y:100, Z:100, E
100that stepper is still heating up, not sure if it's relevant but it's the one plugged into the driver, not the one plugged into the standard driver
EDIT3: 40mm fan is screaming but stepper is getting hotter than I expected... I'll hut the printer down, don't want it to overheat while I'm gone
-
@alanknight said in one Z stepper getting very hot, other fine?:
; Motor remapping for dual Z
M584 X0 Y1 Z2:3 E4.5So I think this was the root of your problem as Veti pointed out. Part of the problem was the period instead of colon, but there's more to it that just that. The command must come earlier in config.g than where you have it.
https://duet3d.dozuki.com/Wiki/Gcode#Section_M584_Set_drive_mapping
Order dependence
M584 must come earlier in config.g than any M350 and M906 commands. If it creates new axes, it must also be earlier than any M92, M201, M203, M208, M350, M566, M574 , M667 and M669 commands.
ExampleM584 X0 Y1 Z2:3 E4:5:6 ; Driver 0 controls the X motor, 1 controls Y, 2 and 3 control Z motors, 4 5 and 6 control E motors
VERY IMPORTANT! Assigning a drive using M584 does not remove its old assignment. Therefore, if you assign a drive that defaults to being an extruder drive, you should also assign the extruder drives explicitly as in the above example. Failure to do so may result in unexpected behaviour.You need to move your M584 command up above the M350 command. Sorry. I should have caught that sooner.
-
no need to say sorry, you're doing me a favour spending your time helping me, I owe you one
edited config file to this...
M569 P0 S0 ; X Drive 0 goes backwards
M569 P1 S0 ; Y Drive 1 goes backwards
M569 P2 S1 ; Z1 Drive 2 goes forwards
M569 P3 S1 ; Z2 Drive 3 goes forwards
M569 P4 S0 ; extr Drive 4 goes backwardsM584 X0 Y1 Z2:3 E4:5 ; Motor remapping for dual Z
M350 X16 Y16 Z16:16 E16 I1 ; Configure microstepping with interpolation
M92 X80 Y80 Z2555:2555 E93 ; Set steps per mm
M566 X900 Y900 Z6:6 E500 ; Set maximum instantaneous speed changes (mm/min)
M203 X6000 Y6000 Z90:90 E3000 ; Set maximum speeds (mm/min)
M201 X1000 Y1000 Z50:50 E500 ; Set accelerations (mm/s^2)
M906 X600 Y600 Z750:750 E1600 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 X0 Y0 Z0 S1 ; Set axis minima
M208 X200 Y180 Z200 S0and
AMM906 Motor current (mA) - X:600, Y:600, Z:750, E:1600:1600, idle factor 30%
AMM913 Motor current % of normal - X:100, Y:100, Z:100, E100I'll give it a go
thanks for all the help
EDIT: it's about an hour into a print, all steppers nice and cool, thanks again for the help
-
Glad that's sorted out.
-
What was happening is that when the M906 command was executed, the motor connected to E1 output was configured as an extruder, so it got 1600mA. That's why we say that M584 must come before M906. Similarly for M350.
-
no more hot motors... but I think I've messed something else up, the auto bed leveling doesn't work anymore (or maybe updating firmware broke something?)
to be fair, I was still fine tuning it, I think my bed has sagged a little in the middle, I'm using a buildtac bed (the magnetic one you can lift the tray off) which might throw it off a little too
when I try to run auto bed leveling, or mesh grid leveling the Z comes down, hits the bed and doesn't stop till the motors stall
it doesn't move X/Y at all, here's my config file
; Configuration file for Duet WiFi (firmware version 1.20 or newer)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool on Wed Jun 13 2018 17:00:33 GMT+0100 (British Summer Time); General preferences
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves; Network
M550 PMy printer ; Set machine name
M552 S1 ; Enable network
M587 S"tripe" P"m580umuu" I192.168.1.89 J192.168.1.254 K255.255.255.0 ; Configure access point and IP addresses. You can delete this line once connected
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet; Drives
; Define Drives
; Physical Drive connectionM569 P0 S0 ; X Drive 0 goes backwards
M569 P1 S0 ; Y Drive 1 goes backwards
M569 P2 S1 ; Z1 Drive 2 goes forwards
M569 P3 S1 ; Z2 Drive 3 goes forwards
M569 P4 S0 ; extr Drive 4 goes backwardsM584 X0 Y1 Z2:3 E4:5 ; Motor remapping for dual Z
M350 X16 Y16 Z16:16 E16 I1 ; Configure microstepping with interpolation
M92 X80 Y80 Z2555:2555 E93 ; Set steps per mm
M566 X900 Y900 Z6:6 E500 ; Set maximum instantaneous speed changes (mm/min)
M203 X6000 Y6000 Z90:90 E3000 ; Set maximum speeds (mm/min)
M201 X1000 Y1000 Z50:50 E500 ; Set accelerations (mm/s^2)
M906 X600 Y600 Z750:750 E1600 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 X0 Y0 Z0 S1 ; Set axis minima
M208 X200 Y200 Z200 S0 ; Set axis maxima; Endstops
M574 X1 Y1 Z1 S0 ; Set active low endstops;Z-Probe
M558 P1 H5 F120 T6000 ; Set Z probe type to unmodulated and the dive height + speeds
G31 P400 X40 Y0 Z-4 ; Set Z probe trigger value, offset and trigger height
M557 X40:160 Y40:160 S20 ; Define mesh grid; Heaters
M305 P0 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S120 ; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 1
M143 H1 S320 ; Set temperature limit for heater 1 to 280C; Fans
M106 P0 S0.85 I0 F500 H1 T45 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P1 S0.5 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S0.5 I0 F500 H1 T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C; Automatic saving after power loss is not enabled
; Custom settings are not configured
and bed.g
; bed.g
; called to perform automatic bed compensation via G32
;
; generated by RepRapFirmware Configuration Tool on Wed Jun 13 2018 17:00:32 GMT+0100 (British Summer Time)M561 ; clear any bed transform
; Probe the bed at 5 points
G30 P0 X30 Y30 H0 Z-99999
G30 P1 X30 Y185 H0 Z-99999
G30 P2 X185 Y185 H0 Z-99999
G30 P3 X185 Y30 H0 Z-99999
G30 P4 X100 Y100 H0 Z-99999 S
I'm looking again and again, googling etc. but can't figure it out
sorry to keep pestering you guys with questions!
Alan
-
@alanknight said in one Z stepper getting very hot, other fine?:
M558 P1 H5 F120 T6000 ; Set Z probe type to unmodulated and the dive height + speeds
G31 P400 X40 Y0 Z-4 ; Set Z probe trigger value, offset and trigger heightWhat type of Z probe are you using? The Z-4 parameter in your G31 line says that it triggers when the nozzle is 4mm below the bed, which surely isn't right. See https://duet3d.dozuki.com/Wiki/Test_and_calibrate_the_Z_probe to calibrate the trigger height.
-
IR probe, from the duet3d website
I'll swap that -4 to a 4, that's probably my mistake!
I fell on my head 3 years ago, left me with a bit of brain damage, I make silly mistakes like that and then can't see them no matter how much I look
thanks again for the help, it's printing right now, I'll give it a try when it's finished
Alan
EDIT: it's still printing, watching it print the z probe reads 535 when it's over what it's printing
I'm thinking that must be the perfect height? - it's reading the high of the last layer it's printing ontop of.... so I can set the z trigger to 535 and z height above nozzle to 0 ?
EDIT: it's not just a Z problem, X moves too far left and crashes into the end stop too... it ignores the end stop and tires to power through
-
I fixed it...I had z probe offset at 40 when it should have been -40
had to add some Y offset too
thanks
Alan
