Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Moved printer, attempting print damaged board, blew another

    Scheduled Pinned Locked Moved
    Duet Hardware and wiring
    6
    17
    1.2k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Stephen6309undefined
      Stephen6309 @bass4aj
      last edited by

      @bass4aj Looks like U3 has blown.

      bass4ajundefined 1 Reply Last reply Reply Quote 0
      • bass4ajundefined
        bass4aj @Stephen6309
        last edited by

        @stephen6309 What does U3 control, and what could cause it to blow? I have yet to test it, but I am wondering if maybe there is a short in the PCB bed? there is no visible burning or damage, but I did notice it was heating unevenly before I blew the board.

        1 Reply Last reply Reply Quote 0
        • Arkadiuszundefined
          Arkadiusz
          last edited by

          If it occurred twice with 2 boards that would indicate there is some fault with your hardware. Problem happens when you are trying to print, so lets narrow it down to heaters.

          bass4ajundefined 1 Reply Last reply Reply Quote 1
          • bass4ajundefined
            bass4aj @Arkadiusz
            last edited by

            @arkadiusz good idea. do you know what I should look for with a multimeter? I agree its likely hardware but I am not sure how/what to look at.

            1 Reply Last reply Reply Quote 0
            • Vetiundefined
              Veti
              last edited by

              check the resistance of the heater.
              then check the resistance of between the heater and the thermistor.

              do this with the bed and hotend.

              there should be a little bit of resistance for the heater and no resistance between heater and thermistor.
              do wiggle the wires while testing.

              bass4ajundefined 1 Reply Last reply Reply Quote 1
              • bass4ajundefined
                bass4aj @Veti
                last edited by

                @veti resistance between heater and thermistor? The heater is a pcb bed and the thermistor is a cartridge style pt1000 attached by Kapton tape. Or are they linked through the board somehow?

                1 Reply Last reply Reply Quote 0
                • Vetiundefined
                  Veti
                  last edited by

                  they should not, but the there could be a short on the hotend. when you power the hotend that would send vin to the thermistor connector.

                  bass4ajundefined 2 Replies Last reply Reply Quote 0
                  • bass4ajundefined
                    bass4aj @Veti
                    last edited by

                    @veti Ah gotcha. I will get those checked and post back. Thanks

                    1 Reply Last reply Reply Quote 0
                    • dc42undefined
                      dc42 administrators
                      last edited by

                      What PSU are you using, and have you checked that it is outputting the correct voltage? Over-voltage at the input could cause U3 to fail.

                      Duet WiFi hardware designer and firmware engineer
                      Please do not ask me for Duet support via PM or email, use the forum
                      http://www.escher3d.com, https://miscsolutions.wordpress.com

                      bass4ajundefined 1 Reply Last reply Reply Quote 0
                      • bass4ajundefined
                        bass4aj @Veti
                        last edited by

                        @veti there is no resistance between either heater/thermistor. Both heaters have some resistance. Looks normal. @dc42 Its some generic supply that M3D put on the Promega printer. Its a 24V supply. DWC reads a constant 23.7V or so, and a check with the multimeter (after detaching from the board) shows 24.1V.

                        1 Reply Last reply Reply Quote 0
                        • bass4ajundefined
                          bass4aj @dc42
                          last edited by

                          @dc42 I also just confirmed, its not U3 that blew. L2 blew. I was touching it with a pick and the whole part just fell off lol

                          1 Reply Last reply Reply Quote 0
                          • bass4ajundefined
                            bass4aj
                            last edited by bass4aj

                            @dc42, what kind of things could cause L2 to fail? I should also mention I saw a different thread in the forum with a similar bed issue (but not quite the same). In that post, you suggested to disconnect the bed ground and tape it to the frame. On the first board when I did that, the bed heat light stayed on, but the bed stopped heating up on start-up if that helps.

                            1 Reply Last reply Reply Quote 0
                            • dc42undefined
                              dc42 administrators
                              last edited by

                              L2 masy blow if either U3, C6 or C12 fails. Unless C6 or C12 looks damaged, my guess is U3.

                              Duet WiFi hardware designer and firmware engineer
                              Please do not ask me for Duet support via PM or email, use the forum
                              http://www.escher3d.com, https://miscsolutions.wordpress.com

                              1 Reply Last reply Reply Quote 1
                              • First post
                                Last post
                              Unless otherwise noted, all forum content is licensed under CC-BY-SA